Glory Bright A808 Remote Control Drone Instruction Manual
- June 5, 2024
- Glory Bright
Table of Contents
AGES 14+
A808 (Setting height & Camera Version)
6-Axis Gyro System 2.4GHz SChannel
360°Flips
INSTRUCTION MANUAL
- Intelligent Hovering
- Headless mode
- One key flip
- One key spiral stunt
- One key balance recovery system
- One key return in Headless mode
- Steady Hovering
- New Control Mode with Trimming
Please read the Instruction Manual carefully before using it. Please keep it for your further reference.
SAFETY CAUTION TIPS:
- The drone is not a toy. Make sure to play it as per the instruction manual, any modification or improper use may cause unexpected danger or risk.
- This product is not suitable for kids under 14 years old. Make sure the drone is operated in safe surroundings.
- Please play this drone to fly away from a person or obstacle, at least 4 meters distance.
- This product can fly indoors or outdoor, do not fly it in unsafe places, such as heat sources, high-voltage power cables,s or no-fly zone.
- In order to avoid short-circuiting or battery damage, do not use other USB cables to charge the drone.
- Do not touch the drone while it is flying or moving.
- Do not mix old and new batteries.
- Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries
PACKING LIST
Drone and Controller details
How to install the battery into the controller
- Use a screwdriver to open the battery compartment cover (see Pic.1)
- Put the battery inside the battery compartment as per correct polarity(see Pic.2)
- Fix the battery compartment cover (see Pic.3)
WARNING
- Do not use different brands or types of batteries.
- Do not mix new and old batteries.
- Install the batteries with the correct polarity.
How to charge the drone
- Take out the battery compartment from the drone…
- Plug USB into a power source and then into the battery, the indicator light will be on while charging, and the indicator light will shoot off once fully charged.
- Fully charging time is approximately 60-70 minutes; flying time is approximately 5-6 minutes.
Pre-flight preparation
- Put the drone on the flat floor, and turn on the swift on the drone. When the indicator light is flashing, the drone is ready to fly.
- Turn on the swift on the transmitter, push the left joystick to the highest point and push to the lowest point, the drone’s indicator light changes to keep on lighting, which means that the frequency match successfully.
- After match frequency, please push the button “one-key correction” and then press the button lake off/landing”.
- Gyro correction and motor unlock
Push the left and right joystick as below picture for around 2 seconds, the indicator light of the drone keeps on and the propeller starts moving.
You can press the button take off/landing” or push both joysticks to the highest point to start to fly the drone.
How to operate the drone
| Push the left joystick up, the drone will fly up Push the left joystick
down. the drone will fly clown
---|---
|
Push the right joystick up, the drone will fly forward Push the light joystick
down. the drone will fly beard
|
Push the left joystick left, the drone will turn leftward Push the left
joystick right, the drone will turn rightward
| Push the right joystick left, the drone will fly to left side Push the right
joystick right. the drone will fly to right side
How to trim the drone
If
the drone flies skewing forward, please press the button “backward trimming”
If the drone flies skewing backward, please press the button “Forward
trimming”
If
the drone flies skewing leftward, please press the button “rightward trimming’
If the drone flies skewing rightward, please press the button “leftward
trimming”
Headless Mode
Headless Mode After taking off the drone, press the button “Headless mode”,
the indicator light on the drone flashes and the transmitter has a sound “Di
Dr; If you want to exit from “headless mode”, just press the button “headless
mode” again.
One Key Return
When the drone flies far away, the “one key return° button can recall the
drone. Press the button “one key return”, and the indicator light on the drone
flashing; If you want to exist from “one key return”, just press the button
°one key return” again. During returning, if push the right joystick up or
down, “returning” will stop.
Speed Switch
During flying, you can press the button “speed switch” to change the flight
speed. The beginning speed for the drone is low speed, press the button ‘speed
switch” and the transmitter has a sound of “di di”, the drone will be at
medium speed; press the button “speed switch” again and the transmitter has a
sound of “di di di “, the drone will be in high speed; press the button °speed
switch” again and the transmitter has a sound of “di”, the drone will be in
low speed again.
360° Flipping
Press the button “flip” and the transmitter has a sound of “di di”, push the
right joystick to “up”, ‘down”, “left”, and “right”, the drone will 360 degree
flip “forward”, “backward”, “leftward” and “rightward” respectively.
How to Start the drone
Option 1: After the frequency match, press the button “take-off/Landing”, and
the drone will fly up and hover in the air.
Option 2: After the frequency match, press the left and right joysticks as in
the shown picture, the propellers begin to move and then press the left
joystick upward, and the drone will fly up and hover in the air.
One Key Landing
Press the button “take off/landing”, and the drone will land slowly. During
landing, you can push the joystick to the assigned location, and the propeller
stops moving.
Urgency Stop
In case of any emergency during the flight, press the button “urgency stop”,
and the drone will land immediately.
WARNING: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. Suppose this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on. In that case, the user is encouraged to try
to correct the interference by one of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help. Remote
control FCC ID: 2AWUGA808 WIFI FCC ID: 2AWUGA808W
“This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1 this device may not cause harmful
interference, and (2 this device must accept any interference received,
including in reference that may cause undesired operation.”
MADE IN CHINA
VS FPV USER MANUAL
- Install the app “VS FPV” on the mobile device. Please scan the following QR code to download the app “VS FPV” and install it, or search it in Apple Appstore or Google Play through the app name “VS FPV”, then download and install it.
| |
---|---|---
https://itunes.apple.com/app/id1195776335| https://play.google.com/store/apps/details?id=et.song.vspfv| https://www.pgyer.com/xob4 - Connect to WiFi Camera. Power on the Drone to power on the WiFi camera. b, press the setting button of your mobile device to search WiFi AP named “VSLCAM m” and then connect it, as pic 1
- Run the App” VS FPV”, and Pic 2 should be shown on your mobile device.
- Press the button “CONNECT” to video and control interface like pic3
a, press button “Off” to open control interface like pic4
b, press the button to open the altitude hold mode control button. like pic5
c, press the Menu button to open the remaining control button like pith 5, Press the “?” button to enter help information.like pic7,pic8,pic9,pic10
