Trulyway Electronic Development J18 wireless earphone User Manual
- June 5, 2024
- Trulyway Electronic Development
Table of Contents
Trulyway Electronic Development J18 wireless earphone
Product specification
- Product name: J18
- Bluetooth version: 5.0
- Battery input: DC 5VM
- Earphone battery: 30mAh
- Charge case battery: 300mAh
- Working time: About 3-4hours
- Sensitive: 92t3dB
- Frequency: 20-2000OHz
- Impedance: 320
- Profile support: HSP/HFP/A2DP/AVRCP
Operation instructions
Binaural Function:
- Touch once: Play/Pause Answer/End a call
- Touch twice on L: Next song
- Touch twice on R: Previous song
- Touch three times on L: Volume
- Touch three times on R: Volume +
- Touch and hold 2 sec: Reject the call
- Touch and hold 2 sec then release: Wake up voice Assistant
Product schematic
- Charge Case
- Charge case indicator
- Charging Port
- Dustproof Mesh
- Touch Area
- MIC
- Earphone Charging Port
- Charge case button
Charging
- Charging with charge case: The case’s red LED flashes slowly.
- Charging with earbuds: The case’s green LED flashes slowly.
- When charging with the earphones: LED remains blue
- Charging time: about 40-60 minutes
Warning:
- To ensure the battery life of the earphone, the earphones and the charge case should be charged once in a month.
- If the earphones are placed in the charge case with being turned off, then press the button on the charge case to start charging
- When charging with charge case please use the 5V/1A charger. Please don’t use the fast charger which over 5V, to avoid damage on the charge case.
Pairing for operating
- Step1. Pick up the earphones from the charge case separately or long touch earphones to turn them on, they will be automatically paired.
- Step2. At this point, open the device’s Bluetooth to search for “118” and then click to connect with device successful, voice prompted ” Bluetooth connected”
When the earphones connect to the same device again, open the lid of charge case it will turn on automatically then reconnect with the device, voice prompt ” Bluetooth Connected”.
Turn on the earphone
- Method A. Touch and hold the area for 2 seconds.
- Method B. Take out earphones from the charge case, they will automatically power on, and enter automatic pairing.
Turn off the earphone
- Method A. Touch and hold the area for 5 seconds.
- Method B. Put earphones into the charge case, they will automatically shut down and enter charging.
*When the earphone disconnected for 3 minutes, it will automatically turn off.
Calling
When connected with mobile phone, the incoming call will be announced with an
English voice reminder, touch once any earphone to answer current callI. Long
touch for 2 seconds to reject the call. If you want to end the current call,
touch once anyY earphone to stop.
FAQ
When the earphones can’t be turned on
Check if the earphone has power (after the charge case is connected to the
USB, and the earphone is charged in the charge case for more than 1 hour).
When the earphones have only one side sound or earphones can’t pair successfully
- Make Sure that both earphones are powered and can be turned on normally.
- When the earphones are in the off state, press the earphones for 7seconds to restore the factory settings.
- Touch 2 seconds to turn on the earphones or take the earphone out of thecharge case(when the charge case is powered ) the earphone will power on voluntarily, then you can connect with the device.
When the mobile phone cannot find the device
- Confirm that the two earphones are turned on.
- Check if the earphone is connected to other devices.
- Change a clear area and reconnect it again.
When the earphone is stuck or disconnect while talking or playing music
- The earphone is low on battery
- The distance between the mobile phone and the earphone is more than 10 meters.
- There is large area of signal obstruction between the mobile phone and the earphone, such as a wall.
- The left and right ears are not paired and synchronized, and need to be shut down and re-paired.
Attention
- Please don’t change the built-in battery by yourself.
- Please don’t put the headset under wet or rainy place.
- Please don’t expose the headset under the blazing sun, event not close fire to avoid battery accident.
- Please don’t disassemble the headset if unprofessional.
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not Occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.