Brookstone 707559BRS RC SMART DRONE Instruction Manual

Brookstone 707559BRS RC SMART DRONE

In order to use it correctly and safely, please read this instruction manual carefully before use, and keep it for future reference.

ACCESSORIES LIST

Check carefully before assembly

THE INSTRUCTION ON LITHIUM BATTERY CHARGING

Remove the drone battery from the battery box; charge the battery with the special USB charger, and connect the 2.0 port of the dedicated USB charging cable with the power terminal (mobile phone charger, Computer, power bank, car charger, the USB indicator light is off at this time. Insert the battery plug into the USB charger correctly. The USB indicator light is on now, indicating that charging is in progress. After the charging is completed, the USB indicator is off, and the charging time is about 50 minutes

WARNING: If you do not want to play this aircraft. Please disconnect the battery wire from the circuit board.

TRANSMITTER BATTERY INSTALLATION

Install method of the batteries: Open the battery cover on the back of the transmitter, correctly, then load AA batteries correctly as per the polarity shown (Batteries are not included). Battery

FLYING PRACTICE

To master the aircraft, please try the following flying practices.

3D FLIP FLYING

After the current basic functions can be skillfully operated, you can play some thrilling rolling actions operate the throttle stick, and adjust the drone height to 3 meters above the ground, hover ready, and press the roll button on the remote control. At this time, the remote control will make a “Di” sound, push the direction handle at the same time, and push backward to roll backward. Press the roll button each time, it can only complete one roll. You can continue to roll after you know the drone well!

SPECIFICATIONS & EQUIPMENT

FCC STATEMENT: THIS DEVICE COMPLIES WITH WTH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. RETAIN THE PACKAGING FOR FUTURE REFERENCE. COLORS AND CONTENTS MAY VARY FROM THOSE ILLUSTRATED. THE BROOKSTONE TRADEMARKS, NAMES, AND LOGOS ARE OWNED BY BKST BRAND HOLDINGS, LLC. 2020. ALL RIGHTS RESERVED. MANUFACTURED, MARKETED, AND DISTRIBUTED BY INNOVATIVE DESIGNS, LLC UNDER LICENSE.

Innovative designs

INNOVATIVE DESIGNS, LLC 132 W. 36TH ST., 8TH FLOOR NEW YORK, NEW YORK 10018 212-695-0892
ITEM NUMBER:  707559BRS FACTORY CODE: F12906/20L707559

Remote control instructions

1. Frequency correction introduction: When the drone is turned on, the light flashes quickly to detect and correct the gyroscope. When the detection is completed, the light flashes slowly. When turning on the remote control and hearing a “Di” sound, the drone light changes to flash quickly. After 3 seconds, the remote control makes a “Di” sound again, and the light is always on, and then the drone light is always on too. The frequency correction is completed.
2. Take-off introduction: the drone must unlock first, without unlocking, the one-key ascending is not functional, push the left joystick to the upper to unlock the drone, then push the upper again or press the one-key ascending button, and the drone takes off.
3. Correction introduction: The left and right joysticks of the remote control simultaneously pull down right and left 45 for the gyroscope correction, and fine-tuning to the “0” position. When the correction is finished, the remote control will make a “Di” SOund and the drone light flashes quickly, the calibration is completed, and the drone light is always on.

Headless Mode Button: Press the button to enter Headless Mode. Press again to cancel Headless Mode. Hold the button for 3 seconds for automatic aircraft landing.

ASSEMBLY STEPS

• When assembling, follow the assembly steps one by one

1. Battery Installation
2. Propeller installation
3. Safety guards installation

Note: When installing the propeller, the corresponding blades should be consistent with the numbers on the body frame.

HOW TO CONTROL

NOTICE

If the aircraft is rotating in the air uncontrollably, adjust the rudder trimming buttons until the aircraft is stable.

FCC Statment

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television re can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: option, which

• Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
  (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>