MISSION TECHNOLOGY E18 Smart Watch User Guide
- June 5, 2024
- MISSION TECHNOLOGY
Table of Contents
Smartwatch
User Guide
Watch operators manual
Install the bracelet APP
Scan the following Qr code or go to the ;OP store to download an instill -Funkeep’
http://heinlink.com/heinDownload.html
Equipment requirements Android devices support android 5.0 and above, and mainstream android smartphones with Bluetooth 4.0 and above. Apple Devices Support los to or higher, and (PHONE 6 or higher.
Bluetooth ComeNion: After a successful match. the APP Automatically Saves the
Bracelet’s Bluetooth address, and when the APP is open or running in the
background, it automabcally searches for and connects to the bracelet.
Data synchronization: Manually pull down the sync data on the APP’s home page;
the bracelet can store 7 days of offline data. The more data there is. the
longer the sync time will be, up to about 2 minutes.
I The watch is hooked up to the phone
This wristband is a dual bluetooth call wristband. To use all the functions,
you need to bind two Bluetooth (APP Bluetooth and Native Audio Bluetooth)
1. APP Bluetooth Connection: Download Funkeep, open the phone’s Bluetooth,
access the APP’s device, device interface, search for E18 and cidc bind, which
sync the data, uses, and does everything but play music and talk. Do not
search for bindings directly on the System Bluetooth
Wristband Audio Bluetooth Open Mode
Click on the phone icon in the red box in the status bar of the main interface of the Bracelet to open the Audio Bluetooth.
Click on the phone icon in the red box in the status bar of the main interface of the Bracelet to open the Audio Bluetooth.
Charging
Aim The charger at the metal contacts on the back of the bracelet Connect the other end of the charger to the USB charging head.
The main interface slides down into the status bar
Main interface long press switch theme
Click on
the enter heart rate interface to start measuring, about 15 seconds later, the
current heart rate is displayed. The result of product measurement is for
reference only, not for diagnosis and treatment. Including running, cycling,
swimming, rope skipping and so on.
Music details
After connecting to the APP, the wristband controls the music playing on the
phone
Note: since the counting mode of each movement mode is different for more
accurate counting, please do the corresponding movement state.
Telephone details
- Ring Audio Bluetooth and Mobile Phone Bluetooth connection successful, you can make and receive calls. (Audio Bluetooth name: Audio-E18.)
- You can sync your phone contacts to your bracelet address book in the APP.
- Please do not leave your wristband more than 5 meters away from your mobile phone when making a call, otherwise the quality of the call will be affected. Note: When the power of the bracelet is below 20%. bluetooth 3.0 will automatically turn off and the call function will be suspended.
Setting details
- Click to enter the settings page, you can set the language, select the menu, vibration intensity, screen display and other functions.
Points to note
- No dunking, diving, diving, bathing.
- This product is electronic monitoring products, not as a medical reference, data for reference only.
- Please use carefully to restore factory settings, restore factory settings lead to APP content settings and hand, ring history of all data lost.
- Please avoid strong impact extreme heat and exposure.
- Please do not dismantle, repair or modify this machine by yourself.
- This machine uses the environment for 0 – 45 degrees, forbid to throw it into the fire, lest cause the explosion.
- Hand Ring Wet please use a soft cloth to dry before charging operation, otherwise it will corrosion charging, contact points, leading to charging failure.
- Do not come into contact with chemicals such as gasoline, cleaning solvents, propanols, alcohol or insect repellents.
- Please do not use this product in high voltage and high magnetic environment.
- If you have sensitive skin or wear the bracelet too tightly, you may feel uncomfortable.
- Please wipe off the sweat on your wristwatch band contact with soap, sweat, allergens, or contaminated ingredients, may cause skin allergy itching.
- 11 frequently used, it is recommended to clean the bracelet weekly. Wipe with a damp cloth and mild soap to remove grease or dirt.
- Do not wear a bracelet to take a hot bath or swim.
- Please wipe thebracelet immediately after it is wet to keep it dry.
Frequently asked questionsAnd Solutions
What happens when the APP doesn’t bind to the bracelet?
- Do not connect to the Bracelet via Bluetooth in yourphoneissettings. This will cause the bracelet to be unsearchable in APP(FunKeep). If you already have a bracelet in your phone’s settings, please unbind it first.
- When a user binds to a wristband, they do so by clicking onthe APP device interface, connecting the device, and clickingon the wristband’s Mac address. If any binding fails, please ignore the device in the system Bluetooth before rebinding.
- If any other phone is already connected to the wristband, a wristband can only be connected to one phone.
- If the user can not find the bracelet please put the braceletnear the phone and check the Bluetooth status of the bracelet to see if it is unbound ftf it is bound, you need to unbind it fromthe system’s
Bluetooth first), try Turning Your Phone’s Bluetooth on and off, resetting
your wristband, or resetting your phoneone time
What if the bracelet can’t play music or make or receive calls?
Check to see if the Bracelet Audio Bluetooth and the Mobile System Bluetooth
are connected. If yes, unconnected, follow these steps: (the status barwil
appear small after connecting successfully, headphone icon)
- Ring Audio Bluetooth Unbound Mobile System Bluetooth: Open Audio Bluetooth in the Ring Status Bar, switch on the phone-set Bluetooth search to Audio, and dick bind. If not, search can switch once audio bluetooth switch or bracelet to restore factory settings.
- Bracelet Audio Bluetooth is already tied to Mobile System Bluetooth: Please Check if Bluetooth is on, if Audio Bluetooth is on in the status bar of the bracelet, if both are on, please switch it on once, Bluetooth on Mobile Phone and Audio Bluetooth switch. If you still can not connect successfully, please unbind in the mobile phone system, Bluetooth, and search again.
- Long-term away from the phone, in order to enhance battery life, audio bluetooth switch will automatically turn off, need to be manually turned on, turned on and then automatically reconnected to the phone.
Waft too long for first test heart rate?
For the first time, your heart rate is measured, using a longer signal from
different people to accurately calculate your heart rate
Unable to search for bracelet?
Since the bracelet was not found by the phone during the Bluetooth
broadcast make sure the bracelet is powered, active, and not tied to another
phone, then move the bracelet closer to the phone, and if it still doesn’t
work, turnoff the Bluetooth on the phone, reboot the phone’s Bluetooth in 20
seconds.
When measuring heart rate, why should the bracelet be worn more tightly?
The bracelet uses the light reflection principle, through the light source
penetrates the skin, collectsthe reflection to the sensor’s signal, calculates
your head rate, if wears not tighdy, wil have the environment light to enter
the sensor, will affect the measurement, the precision.
Why didn’t you receive the alert when the alert function was enabled?
ANDROID PHONE : Make sure your phone is connected to your wristband, and
in the settings on your phone, open the appropriate permissions, allow the
‘FunKeep’ APP to access your calls, text messages, address book, and keep
“Funkeer running in the background if your phone is secure With security
software, please add FunKeep as trust. IPHONE H there is no reminder after
connecting, it is recommended to restart the phone to reconnect Again, when
connecting to the bracelet, you must wait for the phone to pop up ( Bluetooth
Pairing request I , ad( on [ pairing before you get a reminder.
Is the bracelet waterproof
IP57 waterproof and dust proof grade support
It is splash-proof and water-resistant, but it is recommended that the device
not be submerged in water. You can wear and use it during exercise (contact
with sweat), rain, and hand washing. Not Suitable for shower, swimming, scuba
diving, water skiing, other activities facing high-speed water and deep-water
activities.
Does the Bluetooth connection need to be open all the time? Disconnect. Is
there more data?
Data is retained on the bracelet host (for up to seven days) until the data is
synchronized. When the Bluetooth connection between the phone andthe bracelet
is successful, the data of the bracelet will be uploaded to the phone
automatically. Please synchronize the data to the phone.
Note: If the call, SMS reminder function is enabled, you must keep
Bluetooth connected. alarm reminder support offline.
Basic parameter
T ype | 1.32 Square screen smartwach | Banat type | U-Palymer |
---|---|---|---|
Display screen | 1.32 Inch IPS | Barret model | 412327 |
Weight | 65g | Barrett capacity | 240mAh |
Length | 25cm | Barnet voltage | DC 3.7V |
waterproof level | 1p67 | Barer poser | 0.1188Wh% |
Material | silica gel leather steel | Paddng 1st | Device itstructoes Charging |
dock
Warning
Consult your doctor before starting a new exercise progran.The smartwatch can,however,monitor your heart rate and blood pressure in real time,it should not be used for any medice purposes.lt is intended to help people live healthier lives. Always consult your doctor before any exercise or diet
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>