Pacific PMVE002 Flex-Sens TPMS Transmitter Installation Guide

Pacific PMVE002 Flex-Sens TPMS Transmitter Installation Guide

WARNING

Before using the Flex-Sens, read and review all instructions and warnings related to the installation and the use of it. Installation is to be done by professionals only. The Flex-Sens (“TPMS”) Tire Pressure Monitor System product is to be used for the replacement of factory installed TPMS or replace non-working TPMS. The TPMS assemblies are meant for the promotion of safety in line with the US Federal Motor Vehicle Safety Standards (FMVSS) TPMS Ruling No. 138 requirements and regulation of the TPMS. Failure to follow the listed installations methods and warnings below may result in the failure of the Flex-Sens to operate properly.

CAUTION

Each TPMS Flex-Sens is a multi-selectable Sensor that has multiple vehicle applications programmed inside them, manufactured to operate in a specific motor vehicle make, model and year using the proper frequencies (315 MHz or 434 MHz) to communicate with the motor vehicle TPM System. Only install TPMS Flex-Sens multi-selectable sensor designated for your specific motor vehicle make, model and year. Improper TPMS installation or the use of unauthorized TPMS Sensors will cause the motor vehicle TPM System to fail to operate properly. Do not install TPMS Flex-Sens multi-selectable sensor(s) in damaged wheels, upon completion of installation, test the motor vehicle TPM System using procedures described in the original manufacturer’s service guide to confirm proper installation. If the TPM System fails to operate properly, check all installation procedures to ensure proper installation and retest. If the TPM System continues to fail to operate, immediately consult with an authorized motor vehicle dealership or Pacific Manufacturingʼs technical support team.

These TPMS Flex-Sens multi-selectable sensor assemblies are designed and manufactured to operate in Original Equipment (OE) wheels and tires only. If Original Equipment wheels and/or tires are not used, the TPM System and the low tire inflation warning threshold of your vehicle’s TPM System may not function or may function incorrectly. If the Original Equipment wheels and/or tires are not used, it is the responsibility of the vehicle owner to ensure that the TPMS is working correctly. Refer to the original Equipment manufacturerʼs vehicle service guide for instructionʼs including the warning thresh hold reset procedure and seek the assistance of an authorized vehicle dealer to ensure that the TPM system, including system compatibility with the non-Original Equipment Wheels and/ or tires, is working properly. The vehicle owner expressly assumes sole and complete responsibility for the TPMS and vehicle function if the Original Equipment wheels and tire are not used. Failure to ensure that the TPMS is working correctly can result in sever injury or death.

Installation and handling methods, procedures

Clamp-In Installation Warning!

1. Interference with rim (prior confirmation)
   • The rim shape should conform to “Dimensions regarding TPMS rim mounting” (our technical data TPMS-0639).
   • Check that the rim A, A’parts and nuts, washers, and nut tightening tools do not interfere.
   • Check that the rim B part and the TPMS transmitter do not interfere.

2. Suitable for mounting
   • Please attach the TPMS transmitter in the direction shown below. Please do not turn it upside down and attach it.

3. Forget washers
   • Be sure to attach a washer when mounting the TPMS transmitter to the rim

Order of Installation for the Clamp-In

Snap-In Installation Warning!

The transmitter should be installed to a valve hole as the direction indicated in Fig. 1, it is necessary that a sensor body and a rubber valve do not interfere with the wheel. Please check part A and part B. If the sensor body or the rubber valve interferes with the wheel, it may cause air leakage.

• Shapes of a valve hole on wheels should be a minimum of 16 millimeters as follows in Fig. 2.
• No Edges and Burris, and Round or Chamfer inside the valve holes need to avoid damages to the valves.
• Around the valve holes, provide a flat area. If the flat area is small, it will be caused not only deterioration of airtightness but also abnormal deformation and damage of the rubber valves.

Order of Installation for the Snap-In

Notes on the product

• Never fit a damaged transmitter to a wheel rim
• Do not fit the tire to the rim unless confident that the valve has been fitted correctly
• Never re-use an old valve core if it has been removed from the valve stem
• Always ensure these components below are replaced with new Flex-Sens parts.

Grommet: Even if there is no damage such as cracking or breaking, replace it with a new one when replacing the tire. Valve cap: Be sure to attach it. Please use our genuine product for the valve cap. In particular, never use the metal cap. Valve core: Use our genuine product (with Ni plating) for TPMS. Puncture repair agent: Be sure to replace the transmitter when used.

TPMS transmitter storage

1. Intrusion of foreign matter
   • Please store the TPMS transmitter indoors. Do not expose it to rainwater or dust outdoors. Ideally, store in dry air with humidity of 30% or less and temperature of 400C or less.
   • Be careful not to let foreign matter such as iron powder, organic solvents, oils, and chemicals adhere to the transmitter even when stored indoors.

2. Fall
   • Be careful not to accidentally drop the TPMS transmitter during storage. Please do not use if you accidentally dropped it when installing it

TPMS certification

For vehicles sold in the U.S.A.
FCC ID: PAXPMVE002, PAXPMVE102

NOTE
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.

For vehicles sold in Canada
NOTE
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

“Perchlorate Material ‒ special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate.”

Warning:： “This product can expose you to chemicals including Lead or more chemicals, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.”

Rated ambient temperature range：-40℃～120℃

Rated voltage：DC3V、Built-in battery

IMPORTANT WARRANTY INFORMATION

All products sold are warranted against defects in workmanship and material under normal use and service for the earlier of (1) a period of 1 year from the date of manufacture, or (2) 9,000 miles/ 15,000 km of use. The warranty obligation of Pacific Industrial is limited to the repair or replacement, at Pacific Industrials factory location, of any product which is returned to Pacific Industrial by the purchaser, within the warranty period, and which Pacific Industrial determines upon examination is defective or not in conformity with the express warranties contained herein.

A prerequisite for any liability is that the correct Pacific Industrial Tire Pressure Sensor for the respective vehicle has been chosen. Pacific Industrialʼs liability is expressly limited to repair or replacement of defective/non-conforming products returned by the purchaser to Pacific Industrial during the warranty period. In lieu of repair or replacement, if Pacific Industrial elects, Pacific Industrial may, upon return of such defective/non-conforming product by purchaser and making a determination of nonconformity or defect, keep the product and refund to purchaser the purchase price. To the extent permitted by law, under no circumstances will Pacific Industrialʼs liability exceed the purchase price of the defective/non- conforming product at issue and PACIFIC INDUSTRIAL DISCLAIMS LIABILITY FOR ALL INDIRECT, CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Customer Warranty Activation Information Sheet

To activate warranty send to: Pacific Manufacturing Ohio,

8955 Seward Road, Fairfield, Ohio 45011 U.S.A.

Part number of sensor being replaced (old sensor ID) circle selection

Pacific/ Schrader/ Siemens VDO / TRW / Beru / Orange / Continental/ Lear / BH Sensor / Other:

Read More About This Manual & Download PDF:

References

• dtsc.ca.gov/hazardouswaste/perchlorate
• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>