MPOW BH474A Soundhot B6 Home Theater 2.0 Soundbar User Manual

June 5, 2024
MPow

MPOW BH474A Soundhot B6 Home Theater 2.0 Soundbar User Manual
MPOW BH474A Soundhot B6 Home Theater 2.0 Soundbar

Packing List

Packing List

  1. Mpow Soundhot B6
  2. Power supply cord set
  3. 3.5mm audio cable
  4. 3.5mm to 2-male RCA cable
  5. Optical-fiber cable
  6. Remote control
  7. Wall mount accessories
  8. Thank-you card 9. User manual

Diagram

Diagram
Diagram

  1. Power button
  2. Volume- / Previous track
  3. Mode switch button
  4. Volume+ / Next track
  5. Optical-fiber input port
  6. Aux-in audio port
  7. Power port

Note: Please connect it to power before using.

Connect power

Note: The default input setting is optical-fiber input mode after booting the speaker.Click the M button to switch among Aux-in input and Bluetooth mode.(Input mode in priority order. Optical-fiber > Aux-in > Bluetooth )

Default input setting

EQ Switch : Simultaneously press and hold both “+” and “M” buttons for 2 seconds

Press button

NOTE: TV Audio Output Setting is Required
When you connect the Soundbar with a TV, please make sure you have set your TV audio to support “external speakers’ and disable the built-in TV speakers.

Remote Control

Remote Control

  1. News mode (Voice Mode)
    News mode

  2. Movie mode
    Modes

  3. Music mode
    Modes

  4. Reconnection mode
    Modes

  5. Pairing mode

Wall Mounting Guide

  1. Mark the location on the wall Choose the mounting height and mark Al; Mark A2 on the right of Al on the same horizontal line; The distance between the 2 spots should be 729mm exactly.
  2. Drill the holes Drill the holes in the marked position.
  3. Install the speaker Insert the wall plugs in the holes; Tighten the screws into the holes through the foam pads; Hang the speaker on the screws;

Wall Mounting Guide
Wall Mounting Guide
Wall Mounting Guide
Wall Mounting Guide

FCC Statement

Any Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions.

  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.

Correct Disposal of This Product

(Waste Electrical& Electronic Equipment)

This Marking shown on the product or its literature, indicate that it should not be disposed with other household wastes at the end of its working life.

To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

Household user should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contact. This product should not be mixed with other commercial wastes for disposal

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one ormore of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

www.xmpow.com | support©xmpow.com
MPOW TECHNOLOGY CO., LTD
Copyright © MPOW Inc. All rights reserved.

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals