zealSound S618 Lapel Wireless Microphone User Manual
- June 5, 2024
- ZealSound
Table of Contents
zealSound S618 Lapel Wireless Microphone
Packing List
- SmartMic*1
- Charging cable*1
- Manual *1
Power on/off
- Power on: Press and hold the switch button for three seconds, the LED indicator flashes blue, and the BT is waiting for a connection.
- Power off: Long press the switch button for three seconds, and the LED indicator will go out.
BT connection
Turn on the BT of the mobile phone, search for “SmartMic” and pair it with it. The indicator light flashes blue once every 5 seconds, and the BT is connected. Automatically shut down without pairing within 5 minutes.
App download
- This device can be used with SmartMike+ App.
- Please scan the QR code below to download the APP.
- Register after download to use.
APP operation
- Open the SmartMike+ APP, the device connection status will be displayed at the top of the screen, and the device logo can be discovered.
- Video Recording Mode
- Recording Mode
- Remote Recording
- After the device is connected, turn on the APP and press the button to count down for three seconds to start the video recording.
- Press the button again during recording to end the recording.
- Lens Switching
- Quickly press the button twice during recording to switch the front and rear lens of the camera.
Power supply and battery
- After the device is connected, the remaining power of the device will be displayed on the top of the phone.
- In the case of a low battery, the indicator light of the device is steady red.
- Fully charged in about 1.5 hours. Please use the included TYPE‐C charging cable for charging. The indicator light is red when charging. The indicator light turns green when the charging is completed.
- The usage time is about 6 hours at full power. Please charge the device fully before using it for the first time.
- Fast charging is not supported.
PRECAUTIONS
- Do not disassemble the device shell without authorization;
- Do not overheat the machine, such as long‐term exposure to sunlight, fire, or similar environments;
- The battery cannot be replaced by itself. If you need to replace it, please contact professional maintenance personnel;
- Do not modify this device without permission, and do not connect external antennas or use other transmitting antennas without permission;
- Direct or indirect damage caused by violation of the rules of use shall be borne by the user;
- Please use a soft dry cloth to clean the device;
- This device is not waterproof; please do not put it in water;
- If you have any questions or problems about this equipment, that this manual does not cover, please contact us.
List of toxic and hazardous substances
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
CE Maintenance
- Risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
- EUT Operating temperature range: 0° C to 40° C.
- The device complies with RF specifications when the device is used at 0mm from your body.
Declaration of Conformity
We hereby declare that this SmartMic is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EU.In
accordance with Article 10(2) and Article 10(10),This product is allowed to be
used in all EU member states.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>