makita GA7080 Angle Grinder Instruction Manual
- June 5, 2024
- Makita
Table of Contents
makita GA7080 Angle Grinder Instruction Manual
SPECIFICATIONS
Model:| GA7080| GA7081| GA7082| GA9080| GA9081|
GA9082
---|---|---|---|---|---|---
Wheel diameter| 180 mm| 230 mm
Max. wheel thickness| 7.2 mm| 6.5 mm
Spindle thread| M14 or M16 or 5/8″
Rated speed (n)| 8,500 min-1| 6,600 min-1
Overall length| 509 mm| 461 mm| 509 mm| 461 mm
Net weight| 6.3 – 6.8 kg| 6.1 – 6.6 kg| 6.0 – 6.5 kg| 6.5 – 8.6 kg| 6.3 – 8.4
kg| 6.2 – 8.3 kg
Safety class| /II
- Due to our continuing program of research and development, the specifications herein are subject to change without notice.
- Specifications may differ from country to country.
- The weight may differ depending on the attachment(s). The lightest and heaviest combination, according to EPTA-Procedure 01/2014, are shown in the table.
Intended use
The tool is intended for grinding, sanding and cutting of metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of the same voltage as indicated on the nameplate, and can only be operated on single-phase AC supply. They are double-insulated and can, therefore, also be used from sockets without earth wire.
For public low-voltage distribution systems of between 220 V and 250 V
Only for model GA7082 / GA9082
Switching operations of electric apparatus cause voltage fluctuations. The operation of this device under unfavorable mains conditions can have adverse effects to the operation of other equipment. With a mains impedance equal or less than 0.20 Ohms it can be presumed that there will be no negative effects. The mains socket used for this device must be protected with a fuse or protective circuit breaker having slow tripping characteristics.
Noise
The typical A-weighted noise level determined according to EN60745-2-3:
Model| Sound pressure level (L pA ) **:
****(dB(A))| Sound power level (L WA ) : (dB(A))|
Uncertainty (K) : (dB(A))**
---|---|---|---
GA7080| 91| 102| 3
GA7081| 91| 102| 3
GA7082| 91| 102| 3
GA9080| 92| 103| 3
GA9081| 92| 103| 3
GA9082| 92| 103| 3
NOTE: The declared noise emission value(s) has been measured in
accordance with a standard test method and may be used for comparing one tool
with another.
NOTE: The declared noise emission value(s) may also be used in a
preliminary assessment of exposure.
WARNING: Wear ear protection.
WARNING: The noise emission during actual use of the power tool can
differ from the declared value(s) depending on the ways in which the tool is
used especially what kind of workpiece is processed.
WARNING: Be sure to identify safety measures to protect the operator that
are based on an estimation of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as the times when the tool
is switched off and when it is running idle in addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum) determined according to EN60745-2-3:
Work mode: surface grinding with normal side grip
Model| Vibration emission (a h , AG ) : (m/s 2
)| Uncertainty (K) : (m/s 2)
---|---|---
GA7080| 5.6| 1.5
GA7081| 6.8| 1.5
GA7082| 6.8| 1.5
GA9080| 5.2| 1.5
GA9081| 6.3| 1.5
GA9082| 6.3| 1.5
Work mode: surface grinding with anti vibration side grip
Model| Vibration emission (a h , AG ) : (m/s 2
)| Uncertainty (K) : (m/s 2)
---|---|---
GA7080| 5.9| 1.5
GA7081| 7.3| 1.5
GA7082| 7.3| 1.5
GA9080| 5.3| 1.5
GA9081| 5.4| 1.5
GA9082| 5.4| 1.5
Work mode: disc sanding with normal side grip
Model| Vibration emission (a h , AG ) : (m/s 2
)| Uncertainty (K) : (m/s 2)
---|---|---
GA7080| 3.6| 1.5
GA7081| 3.2| 1.5
GA7082| 3.2| 1.5
GA9080| 2.5 m/s2 or less| 1.5
GA9081| 2.7| 1.5
GA9082| 2.7| 1.5
Work mode: disc sanding with anti vibration side grip
Model| Vibration emission (a h , AG ) : (m/s 2
)| Uncertainty (K) : (m/s 2)
---|---|---
GA7080| 3.9| 1.5
GA7081| 3.1| 1.5
GA7082| 3.1| 1.5
GA9080| 2.5 m/s2 or less| 1.5
GA9081| 3.1| 1.5
GA9082| 3.1| 1.5
NOTE: The declared vibration total value(s) has been measured in
accordance with a standard test method and may be used for comparing one tool
with another.
NOTE: The declared vibration total value(s) may also be used in a
preliminary assessment of exposure.
WARNING: The vibration emission during actual use of the power tool can
differ from the declared value(s) depending on the ways in which the tool is
used especially what kind of workpiece is processed.
WARNING: Be sure to identify safety measures to protect the operator that
are based on an estimation of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the trigger time).
WARNING: The declared vibration emission value is used for main
applications of the power tool. However if the power tool is used for other
applications, the vibration emission value may be different.
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A to this instruction
manual.
SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
Grinder safety warnings
Safety Warnings Common for Grinding, Sanding, Wire Brushing, or Abrasive Cutting-Off Operations:
-
This power tool is intended to function as a grinder, sander, wire brush or cut-off tool.
Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. -
Operations such as polishing are not recommended to be performed with this power tool. Operations for which the power tool was not designed may create a hazard and cause personal injury.
-
Do not use accessories which are not specifically designed and recommended by the tool manufacturer. Just because the accessory can be attached to your power tool, it does not assure safe operation.
-
The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can break and fly apart.
-
The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or controlled.
-
Threaded mounting of accessories must match the grinder spindle thread. For accessories mounted by flanges, the arbour hole of the accessory must fit the locating diameter of the flange. Accessories that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control.
-
Do not use a damaged accessory. Before each use inspect the accessory such as abrasive wheels for chips and cracks, backing pad for cracks, tear or excess wear, wire brush for loose or cracked wires. If power tool or accessory is dropped, inspect for damage or install an undamaged accessory. After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this test time.
-
Wear personal protective equipment.
Depending on application, use face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and workshop apron capable of stopping small abrasive or workpiece fragments.
The eye protection must be capable of stopping flying debris generated by various operations.
The dust mask or respirator must be capable of filtrating particles generated by your operation. Prolonged exposure to high intensity noise may cause hearing loss. -
Keep bystanders a safe distance away from work area. Anyone entering the work area must wear personal protective equipment.
Fragments of workpiece or of a broken accessory may fly away and cause injury beyond immediate area of operation. -
Hold the power tool by insulated gripping surfaces only, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
-
Position the cord clear of the spinning accessory. If you lose control, the cord may be cut or snagged and your hand or arm may be pulled into the spinning accessory.
-
Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your control.
-
Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body.
-
Regularly clean the power tool’s air vents. The motor’s fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards.
-
Do not operate the power tool near flammable materials. Sparks could ignite these materials.
-
Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock.
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing
pad, brush or any other accessory. Pinching or snagging causes rapid stalling
of the rotating accessory which in turn causes the uncontrolled power tool to
be forced in the direction opposite of the accessory’s rotation at the point
of the binding. For example, if an abrasive wheel is snagged or pinched by the
workpiece, the edge of the wheel that is entering into the pinch point can dig
into the surface of the material causing the wheel to climb out or kick out.
The wheel may either jump toward or away from the operator, depending on
direction of the wheel’s movement at the point of pinching.
Abrasive wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect operating
procedures or conditions and can be avoided by taking proper precautions as
given below.
-
Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces. Always use auxiliary handle, if provided, for maximum control over kickback or torque reaction during start-up.
The operator can control torque reactions or kickback forces, if proper precautions are taken. -
Never place your hand near the rotating accessory. Accessory may kickback over your hand.
-
Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in direction opposite to the wheel’s movement at the point of snagging.
-
Use special care when working corners, sharp edges etc. Avoid bouncing and snagging the accessory. Corners, sharp edges or bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback.
-
Do not attach a saw chain woodcarving blade or toothed saw blade. Such blades create frequent kickback and loss of control.
Safety Warnings Specific for Grinding and Abrasive Cutting-Off Operations:
- Use only wheel types that are recommended for your power tool and the specific guard designed for the selected wheel. Wheels for which the power tool was not designed cannot be adequately guarded and are unsafe.
- The grinding surface of centre depressed wheels must be mounted below the plane of the guard lip. An improperly mounted wheel that projects through the plane of the guard lip cannot be adequately protected.
- The guard must be securely attached to the power tool and positioned for maximum safety, so the least amount of wheel is exposed towards the operator. The guard helps to protect the operator from broken wheel fragments, accidental contact with wheel and sparks that could ignite clothing.
- Wheels must be used only for recommended applications. For example: do not grind with the side of cut-off wheel. Abrasive cut-off wheels are intended for peripheral grinding, side forces applied to these wheels may cause them to shatter.
- Always use undamaged wheel flanges that are of correct size and shape for your selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut-off wheels may be different from grinding wheel flanges.
- Do not use worn down wheels from larger power tools. Wheel intended for larger power tool is not suitable for the higher speed of a smaller tool and may burst.
Additional Safety Warnings Specific for Abrasive Cutting-Off Operations:
- Do not “jam“ the cut-off wheel or apply excessive pressure. Do not attempt to make an excessive depth of cut. Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage.
- Do not position your body in line with and behind the rotating wheel. When the wheel, at the point of operation, is moving away from your body, the possible kickback may propel the spinning wheel and the power tool directly at you.
- When wheel is binding or when interrupting a cut for any reason, switch off the power tool and hold the power tool motionless until the wheel comes to a complete stop. Never attempt to remove the cut-off wheel from the cut while the wheel is in motion otherwise kickback may occur. Investigate and take corrective action to eliminate the cause of wheel binding.
- Do not restart the cutting operation in the workpiece. Let the wheel reach full speed and carefully re-enter the cut. The wheel may bind, walk up or kickback if the power tool is restarted in the workpiece.
- Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback. Large workpieces tend to sag under their own weight. Supports must be placed under the workpiece near the line of cut and near the edge of the workpiece on both sides of the wheel.
- Use extra caution when making a “pocket cut” into existing walls or other blind areas. The protruding wheel may cut gas or water pipes, electrical wiring or objects that can cause kickback.
Safety Warnings Specific for Sanding Operations:
- Do not use excessively oversized sanding disc paper. Follow manufacturers recommendations, when selecting sanding paper. Larger sanding paper extending beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disc or kickback.
Safety Warnings Specific for Wire Brushing Operations:
- Be aware that wire bristles are thrown by the brush even during ordinary operation. Do not overstress the wires by applying excessive load to the brush. The wire bristles can easily penetrate light clothing and/or skin.
- If the use of a guard is recommended for wire brushing, do not allow any interference of the wire wheel or brush with the guard. Wire wheel or brush may expand in diameter due to work load and centrifugal forces.
Additional Safety Warnings:
- When using depressed centre grinding wheels, be sure to use only fiberglass-reinforced wheels.
- NEVER USE Stone Cup type wheels with this grinder. This grinder is not designed for these types of wheels and the use of such a product may result in serious personal injury.
- Be careful not to damage the spindle, the flange (especially the installing surface) or the lock nut. Damage to these parts could result in wheel breakage.
- Make sure the wheel is not contacting the workpiece before the switch is turned on.
- Before using the tool on an actual workpiece, let it run for a while. Watch for vibration or wobbling that could indicate poor installation or a poorly balanced wheel.
- Use the specified surface of the wheel to perform the grinding.
- Do not leave the tool running. Operate the tool only when hand-held.
- Do not touch the workpiece immediately after operation; it may be extremely hot and could burn your skin.
- Do not touch accessories immediately after operation; it may be extremely hot and could burn your skin.
- Observe the instructions of the manufacturer for correct mounting and use of wheels. Handle and store wheels with care.
- Do not use separate reducing bushings or adaptors to adapt large hole abrasive wheels.
- Use only flanges specified for this tool.
- For tools intended to be fitted with threaded hole wheel, ensure that the thread in the wheel is long enough to accept the spindle length.
- Check that the workpiece is properly supported.
- Pay attention that the wheel continues to rotate after the tool is switched off.
- If working place is extremely hot and humid, or badly polluted by conductive dust, use a short-circuit breaker (30 mA) to assure operator safety.
- Do not use the tool on any materials containing asbestos.
- When use cut-off wheel, always work with the dust collecting wheel guard required by domestic regulation.
- Cutting discs must not be subjected to any lateral pressure.
- Do not use cloth work gloves during operation. Fibers from cloth gloves may enter the tool, which causes tool breakage.
- Make sure there are no electrical cables, water pipes, gas pipes etc. that could cause a hazard if damaged by use of the tool.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury
FUNCTIONAL DESCRIPTION
CAUTION: Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool.
Shaft lock
Press the shaft lock to prevent spindle rotation when installing or removing
accessories.
Fig.1:
Shaft lock
NOTICE: Never actuate the shaft lock when the spindle is moving. The tool may be damaged.
Switch handle mounting positions
Only for model GA7080 / GA9080
CAUTION: Always make sure that the switch handle is locked in the desired position before operation.
The switch handle can be rotated to either 90° left or right to fit your work needs. First, unplug the tool. Press the lock button and rotate the switch handle to left or right fully. The switch handle will be locked in that position.
Fig.2:
- Motor housing
- Lock button
- Handle
Switch action
CAUTION: Before plugging in the tool, always check to see that the switch
trigger actuates properly and returns to the “OFF” position when released.
CAUTION: Make sure to switch off the tool in case of a blackout or
accidental shut down such as unplugging of the power cord. Otherwise the tool
will start unexpectedly when the power supply is recovered and cause an
accident or personal injury.
There are three patterns of the switch action depending on country.
Fig.3:
- Switch trigger
- Lock lever
For tool with the lock-on switch
Country specific
CAUTION: Switch can be locked in “ON” position for ease of operator comfort during extended use. Apply caution when locking tool in “ON” position and maintain firm grasp on tool.
To start the tool, simply pull the switch trigger (in the B direction).
Release the switch trigger to stop.
For continuous operation, pull the switch trigger (in the B direction) and
then push in the lock lever (in the A direction).
To stop the tool from the locked position, pull the switch trigger fully (in
the B direction), then release it.
For tool with the lock-off switch
Country specific
To prevent the switch trigger from accidentally pulled, a lock lever is
provided.
To start the tool, push in the lock lever (in the A direction) and then pull
the switch trigger (in the B direction).
Release the switch trigger to stop.
NOTICE: Do not pull the switch trigger hard without pressing in the lock lever. This can cause switch breakage.
For tool with the lock-on and lock-off switch
Country specific
CAUTION: Switch can be locked in “ON” position for ease of operator comfort during extended use. Apply caution when locking tool in “ON” position and maintain firm grasp on tool.
To prevent the switch trigger from accidentally pulled, a lock lever is
provided.
To start the tool, push in the lock lever (in the A direction) and then pull
the switch trigger (in the B direction).
Release the switch trigger to stop.
For continuous operation, push in the lock lever (in the A direction), pull
the switch trigger (in the B direction) and then pull the lock lever (in the C
direction).
To stop the tool from the locked position, pull the switch trigger fully (in
the B direction), then release it.
NOTICE: Do not pull the switch trigger hard without pressing in the lock lever. This can cause switch breakage.
Indication lamp
Only for model GA7080 / GA7081 / GA9080 / GA9081
Fig.4:
Indication lamp
The indication lamp lights up green when the tool is plugged.
If the indication lamp does not light up, the mains cord or the controller may
be defective.
The indication lamp lights up but the tool does not start even if the tool is
switched on, the carbon brushes may be worn out, or the controller, the motor
or the switch may be defective.
Unintentional restart proof
Only for model GA7080 / GA7081 / GA9080 / GA9081
The tool does not start with the switch being lock-on even when the tool is
plugged.
At this time, the indication lamp blinks in red to show the unintentional
restart proof device is working.
To cancel the unintentional restart proof, return the switch to OFF position.
NOTE: Wait more than one second before restarting the tool when unintentional restart proof works.
Soft start feature
Only for model GA7080 / GA7081 / GA9080 / GA9081
Soft start feature reduces starting reaction.
ASSEMBLY
CAUTION: Always be sure that the tool is switched off and unplugged before carrying out any work on the tool.
Installing side grip (handle)
CAUTION: Always be sure that the side grip is installed securely before
operation.
CAUTION: You can install the side grip on the 3 holes. Install the side
grip on one of the holes according to the operation.
Screw the side grip securely on the position of the tool as shown in the
figure.
Fig.5
Installing or removing loop handle
Optional accessory
CAUTION: Always be sure the bolts on the loop handle is securely
tightened before use.
CAUTION: Hold the gripping area of the loop handle specified in the
figure. Also, keep the hand away from the metal part of the grinder during
operation. Touching the metal part may result in electric shock, if the
cutting attachment cuts live wire unexpectedly.
The loop handle can be more comfortable than the original side grip for some
applications. To install the loop handle, mount it onto the tool as
illustrated and tighten two bolts to fix it.
To remove the loop handle, follow the installation procedure in reverse.
Fig.6:
- Loop handle
- Bolt
- Gripping area
Installing or removing wheel guard (For depressed center wheel, flap disc, flex wheel, wire wheel brush / abrasive cut-off wheel, diamond wheel)
WARNING: When using a depressed center wheel, flap disc, flex wheel or
wire wheel brush, the wheel guard must be fitted on the tool so that the
closed side of the guard always points toward the operator.
WARNING: When using an abrasive cut-off / diamond wheel, be sure to use
only the special wheel guard designed for use with cut-off wheels.
(In some European countries, when using a diamond wheel, the ordinary guard
can be used. Follow the regulations in your country.)
For tool with locking screw type wheel guard
Mount the wheel guard with the protrusions on the wheel guard band aligned
with the notches on the bearing box. Then rotate the wheel guard to such an
angle that it can protect the operator according to work. Be sure to tighten
the screw securely.
To remove wheel guard, follow the installation procedure in reverse.
Fig.7:
- Wheel guard
- Bearing box
- Screw
For tool with clamp lever type wheel guard
Optional accessory
WARNING: The wheel guard must be fitted on the tool so that the closed side of the guard always points toward the operator.
Loosen the nut, and then pull the lever in the direction of the arrow.
Fig.8:
- Nut
- Lever
Mount the wheel guard with the protrusions on the wheel guard band aligned with the notches on the bearing box. Then rotate the wheel guard to such an angle that it can protect the operator according to work.
Fig.9:
- Wheel guard
- Bearing box
Fig.10:
Wheel guard
Securely tighten the nut using a spanner, and then close the lever in direction of the arrow to fasten the wheel guard. If the lever is too tight or too loose to fasten the wheel guard, open the lever and then loosen or tighten the nut using the spanner to adjust the tightening of the wheel guard band.
Fig.11:
- Nut
- Lever
To remove wheel guard, follow the installation procedure in reverse.
Installing or removing depressed center wheel or flap disc
Optional accessory
WARNING: When using a depressed center wheel or flap disc, the wheel guard must be fitted on the tool so that the closed side of the guard always points toward the operator.
CAUTION: Make sure that the mounting part of the inner flange fits into the inner diameter of the depressed center wheel / flap disc perfectly. Mounting the inner flange on the wrong side may result in the dangerous vibration.
Mount the inner flange onto the spindle.
Make sure to fit the dented part of the inner flange onto the straight part at
the bottom of the spindle.
Fit the wheel / disc on the inner flange and screw the lock nut with its
protrusion facing downward (facing towards the wheel).
Fig.12:
- Lock nut
- Depressed center wheel
- Inner flange
- Mounting part
To tighten the lock nut, press the shaft lock firmly so that the spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise.
Fig.13:
- Lock nut wrench
- Shaft lock
To remove the wheel, follow the installation procedure in reverse.
Installing or removing flex wheel
Optional accessory
WARNING: Always use supplied guard when flex wheel is on the tool. Wheel can shatter during use and guard helps to reduce chances of personal injury.
Fig.14:
- Lock nut
- Flex wheel
- Back up pad
- Inner flange
Follow instructions for depressed center wheel but also use back up pad over wheel. See order of assembly on accessories page in this manual.
Super flange
Optional accessory
Only for tools with M14 spindle thread.
Only 1/3 of efforts needed to undo lock nut, compared with conventional type.
Installing or removing Ezynut
Optional accessory
Only for tools with M14 spindle thread.
Mount inner flange, abrasive wheel and Ezynut onto the spindle so that Makita Logo on Ezynut faces outside.
Fig.15:
- Ezynut
- Abrasive wheel
- Inner flange
- Spindle
Press shaft lock firmly and tighten Ezynut by turning the abrasive wheel clockwise as far as it turns.
Fig.16:
Shaft lock
To loosen the Ezynut, turn the outside ring of Ezynut counterclockwise.
NOTE: Ezynut can be loosened by hand as long as the arrow points the notch. Otherwise a lock nut wrench is required to loosen it. Insert one pin of the wrench into a hole and turn Ezynut counterclockwise.
Fig.17:
- Arrow
- Notch
Fig.18
Installing or removing abrasive disc
Optional accessory
Fig.19:
-
Sanding lock nut
-
Abrasive disc
-
Rubber pad
-
Mount the rubber pad onto the spindle.
-
Fit the disc on the rubber pad and screw the sanding lock nut onto the spindle.
-
Hold the spindle with the shaft lock, and securely tighten the sanding lock nut clockwise with the lock nut wrench.
To remove the disc, follow the installation procedure in reverse.
NOTE: Use sander accessories specified in this manual. These must be purchased separately.
Installing or removing abrasive cutoff / diamond wheel
Optional accessory
WARNING: When using an abrasive cut-off / diamond wheel, be sure to use
only the special wheel guard designed for use with cut-off wheels.
(In some European countries, when using a diamond wheel, the ordinary guard
can be used. Follow the regulations in your country.)
WARNING: NEVER use cut-off wheel for side grinding.
Mount the inner flange onto the spindle.
Fit the wheel / disc on the inner flange and screw the lock nut onto the
spindle.
Fig.20:
- Lock nut
- Abrasive cut-off wheel / diamond wheel
- Inner flange
- Wheel guard for abrasive cut-off wheel / diamond wheel
For Australia and New Zealand
Fig.21:
- Lock nut
- Outer flange 78
- Abrasive cut-off wheel / diamond wheel
- Inner flange 78
- Wheel guard for abrasive cutoff wheel / diamond wheel
Installing wire cup brush
Optional accessory
CAUTION: Do not use brush that is damaged, or which is out of balance.
Use of damaged brush could increase potential for injury from contact with
broken brush wires.
Fig.22:
Wire cup brush
Remove any accessories on spindle. Thread wire cup brush onto spindle and tighten with the wrench.
Installing wire wheel brush
Optional accessory
CAUTION: Do not use wire wheel brush that is damaged, or which is out of
balance. Use of damaged wire wheel brush could increase potential for injury
from contact with broken wires.
CAUTION: ALWAYS use guard with wire wheel brushes, assuring diameter of
wheel fits inside guard. Wheel can shatter during use and guard helps to
reduce chances of personal injury.
Fig.23:
Wire wheel brush
Remove any accessories on spindle. Thread wire wheel brush onto spindle and tighten with the wrench.
Installing dust collecting wheel guard
Dust collecting wheel guard for grinding (for model
GA7080 / GA7081 / GA9080 / GA9081)
Fig.24:
- Lock nut
- Cup-type diamond wheel
- Hubbed cup-type diamond wheel
- Inner flange
- Dust collecting wheel guard
- Bearing box
WARNING: Dust collecting wheel guard for grinding is only for use in grinding flat concrete with a cup-type diamond wheel. Do not use it with grinding stones or for any purpose other than mentioned.
Dust collecting wheel guard for cut-off (for model GA9080 / GA9081 /
GA9082)
Fig.25
NOTE: For information how to install the dust collecting cover, refer to the manual of the dust collecting cover.
Connecting a vacuum cleaner
Optional accessory
WARNING: Never vacuum metal particles generated by operation. Metal
particles generated by such operation are so hot that they ignite dust and
the filter inside the vacuum cleaner.
To avoid dusty environment caused by masonry cutting, use a dust collecting wheel guard and a vacuum cleaner. Refer to the instruction manual attached to the dust collecting wheel guard for assembling and using it.
Fig.26:
- Dust collecting wheel guard for cut-off
- Hose of the vacuum cleaner
OPERATION
WARNING: It should never be necessary to force the tool. The weight of
the tool applies adequate pressure. Forcing and excessive pressure could cause
dangerous wheel breakage.
WARNING: ALWAYS replace wheel if tool is dropped while grinding.
WARNING: NEVER bang or hit grinding disc or wheel onto work.
WARNING: Avoid bouncing and snagging the wheel, especially when working
corners, sharp edges etc. This can cause loss of control and kickback.
WARNING: NEVER use tool with wood cutting blades and other saw blades.
Such blades when used on a grinder frequently kick and cause loss of control
leading to personal injury.
WARNING: Continued use of a worn-out wheel may result in wheel explosion
and serious personal injury.
CAUTION: Never switch on the tool when it is in contact with the
workpiece, it may cause an injury to operator.
CAUTION: Always wear safety goggles or a face shield during operation.
CAUTION: After operation, always switch off the tool and wait until the
wheel has come to a complete stop before putting the tool down.
CAUTION: ALWAYS hold the tool firmly with one hand on housing and the
other on the side grip (handle).
Grinding and sanding operation
Fig.27
Turn the tool on and then apply the wheel or disc to the workpiece.
In general, keep the edge of the wheel or disc at an angle of about 15° to the
workpiece surface.
During the break-in period with a new wheel, do not work the grinder in
forward direction or it may cut into the workpiece. Once the edge of the wheel
has been rounded off by use, the wheel may be worked in both forward and
backward direction.
Operation with abrasive cut-off / diamond wheel
Optional accessory
WARNING: Do not “jam” the wheel or apply excessive pressure. Do not
attempt to make an excessive depth of cut. Overstressing the wheel increases
the loading and susceptibility to twisting or binding of the wheel in the cut
and the possibility of kickback, wheel breakage and overheating of the motor
may occur.
WARNING: Do not start the cutting operation in the workpiece. Let the
wheel reach full speed and carefully enter into the cut moving the tool
forward over the workpiece surface. The wheel may bind, walk up or kickback if
the power tool is started in the workpiece.
WARNING: During cutting operations, never change the angle of the wheel.
Placing side pressure on the cut-off wheel (as in grinding) will cause the
wheel to crack and break, causing serious personal injury.
WARNING: A diamond wheel shall be operated perpendicular to the material
being cut.
For model GA7080 and GA9080, you can rotate the switch handle.
Usage example: operation with abrasive cut-off wheel with GA7080 / GA9080
Fig.28
Usage example: operation with abrasive cut-off wheel with GA7081 / GA7082 /
GA9081 / GA9082
Fig.29
Usage example: operation with diamond wheel with GA7080 / GA9080
Fig.30
Usage example: operation with diamond wheel with GA7081 / GA7082 / GA9081 /
GA9082
Fig.31
Operation with wire cup brush
Optional accessory
CAUTION: Check operation of brush by running tool with no load, insuring that no one is in front of or in line with brush.
NOTICE: Avoid applying too much pressure which causes over bending of wires when using the wire cup brush. It may lead to premature breakage.
Usage example: operation with wire cup brush
Fig.32
Operation with wire wheel brush
Optional accessory
CAUTION: Check operation of wire wheel brush by running tool with no load, insuring that no one is in front of or in line with the wire wheel brush.
NOTICE: Avoid applying too much pressure which causes over bending of wires when using wire wheel brush. It may lead to premature breakage.
Usage example: operation with wire wheel brush
Fig.33
MAINTENANCE
CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance.
NOTICE: Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
NOTE: Do not loosen the screw on the cover.
Otherwise the cover may be opened accidentally.
Fig.34:
Screw
Air vent cleaning
The tool and its air vents have to be kept clean.
Regularly clean the tool’s air vents or whenever the vents start to become
obstructed.
Fig.35:
- Exhaust vent
- Inhalation vent
OPTIONAL ACCESSORIES
CAUTION: These accessories or attachments are recommended for use with
your Makita tool specified in this manual. The use of any other accessories or
attachments might present a risk of injury to persons.
Only use accessory or attachment for its stated purpose.
If you need any assistance for more details regarding these accessories, ask
your local Makita Service Center.
Fig.36
– | 180 mm | 230 mm |
---|---|---|
1 | Side grip / Loop handle | |
2 | Wheel guard for depressed center grinding wheel / flap disc / flex wheel / |
wire wheel brush
3| Inner flange / Super flange 12
4| Depressed center grinding wheel / Flap disc
5| Lock nut / Ezynut 12
6| Wheel guard for abrasive cut off wheel / diamond wheel 3
7| Inner flange 78 (Australia and New Zealand only) 4
8| Abrasive cut-off wheel / Diamond wheel
9| Outer flange 78 (Australia and New Zealand only) 4
10| Back up pad
11| Flex wheel
12| Rubber pad
13| Abrasive disc
14| Sanding lock nut
15| Wire wheel brush
16| Wire cup brush
17| –| Side grip for dust collecting wheel guard
18| –| Dust collecting wheel guard for cut-off 4
19| –| Diamond wheel
20| Dust collecting wheel guard for offset diamond wheel
21| Offset diamond wheel
–| Lock nut wrench
–| Dust cover attachment
NOTE: 1 Only for tools with M14 spindle thread.
NOTE: 2 Do not use Super flange and Ezynut together.
NOTE: 3 In some European countries, when using a diamond wheel, the
ordinary guard can be used instead of the special guard covering the both side
of the wheel. Follow the regulations in your country.
NOTE: 4 Use Inner flange 78 and Outer flange 78 together. (Australia and
New Zealand only)
NOTE: Some items in the list may be included in the tool package as standard accessories. They may differ from country to country.
Annex A: EC Declaration of Conformity
We as the manufacturers: Makita Europe N.V., Business ad d ress: Jan-Baptist
Vinkstraat 2, 3070 Kortenberg, BELGIUM. Authorize Hiroshi Tsujimura for the
compilation of the technical file and declare under our sole responsibility
that the product ( s) ; Designation: Angle Grinder. D esignation of Type(s):
GA7080, GA7081, GA7082, GA9080, GA9081, GA9082. Fulfills all the relevant
provisions of 2006/42/EC and also fulfills all the relevant provisions of the
following EC/EU Directives: 2014/30/EU, 2011/65/EU and are manufactured in
accordance with the following Harmonised Standards:
EN 60745-1:2009+A11:2010, EN 60745-2-3:2011+A2:
2013+A11:2014+A12:2014+A13:2015, EN 55014-1:2017, EN 55014-2:2015, EN IEC
61000-3-2:2019, EN 61000-3- 3:2013+A1:2019 (GA7080, GA7081, GA9080, GA9081),
EN 61000-3-11:2000 (GA7082, GA9082), EN IEC 63000:2018. P lace of declaration:
Kortenberg, Belgium. Responsible person: Hiroshi Tsujimura, Director – Makita
Europe N.V. ( d ate and signature on the last page)
Makita Europe N.V.
Jan-Baptist Vinkstraat 2,
3070 Kortenberg, Belgium
References
- Makita Canada | The Leader In Power tool Technology
- MAKITA Industrial Power Tools - The Leader In Cordless with 18V LXT Lithium-Ion
- Makita U.S.A | Cordless and Corded Power Tools, Power Equipment, Pneumatics, Accessories
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>