MAKEN SC1306 Tablet Stand User Manual
- June 5, 2024
- MAKEN
Table of Contents
SC1306 Tablet Stand
User Manual
Product Name: Tablet Stand
Model No: SC1306
FCC ID: 2AW2K-SC-306
Cautions!
Warning!- To prevent the risk of fire or electric shock, do not expose
this product to rain or moisture.
Warning!- Do not disassemble this product; otherwise, it may cause
electric shock.
Product Overview
The product is controlled by a single chip microcomputer, thus working status
is timely indicated via LED backlight indication and buzzer sound. IPad
installed is intelligent charging, and the charging current can reach 5V/2.1A
while with the protection of overcharge, overvoltage, and overcurrent
charging. The high-quality MOS tube is used to control the LED backlight
display and the electronic switch of the stand, and the tablet enclosure can
be departed by swiping the card.
By adding or deleting settings through smart ID cards, the shortcuts method or
conventional method can be chosen accordingly to store 1 main card and 10 sub-
cards. To protect the safety usage of users, users can delete a single main
card or a single sub card, while they also can delete all ID card information
with one click.
Specification
a) Power：
Input voltage; AC100V～240V,50Hz/60Hz.
Output voltage;DC24V/1.25A.
b) Working temperature：0℃～40℃; Working humidity：20%～85%.
c) Storage temperature：-10℃～50℃; Storage humidity：10%～90%.
d) Charging current：≤2.1A
Operating Instructions
a) Adding cards: Cards that have been set to the product (eg: primary and
secondary cards) are “associated cards”, and cards that have not been set to
the product are “unassociated cards”.
The primary card： The first card is added when the product is powered on.
The secondary cards： The second to the eleventh card is added when the product
is powered on. Swipe in “Unlinked Card” (blue light flashes 3 times, the
buzzer sounds once), add the main card is complete
| Card type | Qty | Function | Adding method |
|---|
The
primary
card| 1| Add| 1. Power on；
2. Swipe in an unassociated card. When the blue light flashes 3 times and the
buzzer sounds once, it means the primary card is added successfully. This
first the added card will be the primary card.
3. Enter the shortcut setting automatically
The
secondary
cards| 10| Add| 1. Swipe the primary card in red color (less than 3 seconds)
2. Swipe the unassociated cards in black color. Every time you add a
secondary card. When the blue light flashes once and the buzzer sounds once,
it means this secondary card is added. Every time, after you added a secondary
card, it should swipe the primary card to confirm. Only after confirmed by
the primary card, the secondary card is added successfully.
3. Swipe the primary card in red to confirm after you added a secondary card
every time. When the blue light flashes 3 times and the buzzer sounds once,
the secondary card is added successfully.
Shortcuts
setting| –| Shortcuts
setting| 1. After the primary card was added, it will enter the shortcut
setting automatically, and the blue light will be on.
2. The “unassociated cards” that were swiped in later are set as the
“secondary cards”.
3. During the setting process, swipe in the “associated card” or wait for the
setting to time out to exit the shortcut setting (the associated cards valid).
The
secondary
card| 1| deletion| Keep swiping the primary card until the blue light is off
and the red light is on. When the red light is on, remove the primary card
once heard the buzzer sounded once.
Then keep swiping a secondary card, and the red light will be off first. Hold
on to the secondary card, and wait until the red light is on again. When the
red light is on, remove the card once heard the buzzer sounded once. This card
is deleted successfully.
The
primary
card| 1| deletion| Keep swiping the primary card until the blue light is off
and the red light is on. When the red light is on, remove the primary card
once heard the buzzer sounded once.
Then keep swiping the primary card again, and the red light will be off first.
Hold on to the primary card, and wait until the red light is on again. When
the red light is on, remove the card once heard the buzzer sounded once. This
primary card is deleted successfully.
Note: Once delete the primary card, all secondary cards are also deleted
automatically.
Loss of primary card:
Swipe one secondary card five times in a row within 10 seconds after power-on.
Every time, the buzzer will sound once and the red light flashes once. After 5
times operation, all card information will be deleted. And then cut off the
power. The primary card and secondary cards can be added after powering on
again.
Loss of secondary cards:
If all 10 secondary cards have been added, then it will need to delete the
primary card first. And then add the primary card and secondary cards again.
If the secondary cards are not added to 10pcs, then the secondary cards can be
added through the primary card.
The buzzer will sound three times and the red light will flash three times if
cards are deleted unsuccessfully.
c) Use the needle to press the switch in 3 seconds on the bottom of the base.
This operation can clear all saved ID card information. The cards can be added
after power-on again.
d) Backlight is red and the item is on standby if the tablet enclosure is not
inserted into the stand.
e) After the tablet enclosure is inserted into the stand, the backlight will
turn blue and the item is in a working state. In the working state, ID cards
can be added and deleted, and it can swipe the card to depart the tablet
enclosure.IPad is in charge when the power cord is connected.
f) Each time the ID card is swiped when the blue backlight flash and the
buzzer sounds, the user can remove the tablet enclosure after the electronic
switch of the stand is turned on for 8 seconds.
Installation instructions
a) Packing list
b) Stand Mounting
c) Front panel disassembly
d) Frontpanel Insttallation
e) Product usage the separate panel usage
The whole tablet stand assembly and usage
f) RFID Instruction
Swipe the card before taking out the panel
The sound prompt and light color prompt when taking out and assembling the panel.
Attention matters
a) When swiping with the primary card, but the primary card is on swiping
position of the stand at first, and the electronic switch is turned on after
taking the card away from swiping position.
b) When swiping with the secondary card, put the primary card in swiping
position of the stand at first, and the electronic switch is turned, then the
tablet enclosure can be removed. During this operation, no need to take away
the card to remove the tablet enclosure.
c) When the red light is flashing, it cannot add or delete the primary card
and secondary cards, and cannot swipe cards or do any other operations.
d) If there is a malfunction during adding or deleting cards, the LED
indicator on the stand will be turned off, it needs to wait 20 seconds or re-
swipe to restore the working status.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC ID: 2AW2K-SC-306
Documents / Resources
|
MAKEN SC1306 Tablet
Stand
[pdf] User Manual
SC-306, SC306, 2AW2K-SC-306, 2AW2KSC306, SC1306 Tablet Stand, Tablet Stand,
Stand
---|---