ARKON D1 2.4G Digital Hi-Fi Wireless Headphones User Manual
- June 5, 2024
- ARKON
Table of Contents
ARKON D1 2.4G Digital Hi-Fi Wireless Headphones
introduction
ARTISTE 2.4GHz Digital Wireless Headphone uses the latest digital wireless technology that enables you to enjoy crystal sound stereo music and TV sound anywhere inside your home. Simply connect the transmitter to a desired audio source: DVD player, TV set, Hi-Fi system, MP3, iPod, or Smartphone. Without complicated wiring and installation, the system enables you to enjoy thrilling, lifelike sound in hours.
FEATURES
-
2.4GHz Digital Hopping System
OPTICAL/COAXIAL Connection -
Technology Smart Volume Memory preset
Direct Audio Line-In -
Auto On/Off (when without signal)
Enclosed memory foam -
10-degree Acljustable Headband
Top Charge Mechanism
BE CAREFUL
Prolonged exposure to Excessive sound pressure from earphones and headphones may cause permanent hearing loss.
HEADPHONES
COMPONENT PART LIST
FUNCTION SCHEMATIC
HEADPHONE RECEIVER
- For your convenience, rechargeable batteries have been inserted in wireless headphone. Please charge sufficiently before first use.
- The wireless headphone should be turned off before charging.
- If you need to replace the rechargeable batteries, please rotate the ear pad holder and take it away from the headphone cabinet.
- Replace/lnstall 2 pieces of AAA size rechargeable batteries (supplied by ARTISTE) into the battery compartment (RIGHT SIDE).
- Make sure the batteries are placed with the right polarity . + CT~I –
OPERATION
Note: For the initial use, please charge the batteries for 6 hours. If the
headphone is not in use, please place it back on the transmitter.
INSTALLATION TRANSMITTER
- Plug the AC/DC power adaptor in the DC jack at the rear of the transmitter. Connect the supplied AC/DC power adaptor to an electrical wall outlet.
- Rear of the transmitter has audio socket, optical socket and coaxial socket for connecting the Audio Cable to the audio output jack of TV, PC, DVD, iPod, MP3, or Smartphone.
- For TV/DVD/Hi-Fi, switch to -8dB. For CD/MP3, iPod or Smartphone switch to OdB.
Switch to OPTICAL when use the optical cable for connection Switch to COAXIAL
when use the coaxial cable for connection
Switch to AUDIO when use the 3.5/RCA cable for connection
HEADPHONE RECEIVER
Turn on the headphone by pressing the Power button for about 2 seconds. The
LED will light up in RED, and then change to GREEN when Audio Signal link
between Transmitter and Headphone Receiver is established. If no Audio Signal
is detected, this LED will glow in RED constantly.
Adjust the size of the Headband, place the Headphone on your head. To obtain
the desired sound level, adjust the Volume Control on the Headphone.
If interference or poor signal reception occurs, the headphone will be muted
and the LED will change to RED, searching for another channel will be run
automatically.
When the batteries of Headphone are at low level, the LED will blinks in RED.
There will be beeping sound from the headphone in every minute to indicate the
last 5 minutes of working. A beep sound in each of the first 4 minutes, and 2
beep sounds in the last minutes and then it will automatically switch off.
To charge the Batteries in the Headphone, turn OFF the Headphone by pressing
the Power button for about 2 seconds. Place the Headphone on the Transmitter.
The charging process begins automatically, and the CHARGE LED on the
transmitter will light in GREEN when the charging contacts of transmitter and
headphone are matched successfully.
When the charging process (about 6 hours) is completed, the GREEN LED will be
OFF.
For protection of the Transmitter and power saving, the Transmitter will be
switched to Stand-by Mode automatically if there is no Audio Signal for
approximately 5 minutes’ LED will be OFF. If the Audio Signal returns, the
Transmitter will be automatically switched On with LED glows in BLUE. Switch
on the Headphone again to listen to the music.
The Headphone will be switched off automatically if there is no signal from
the Transmitter for about 5 minutes.
WIRED HEADPHONE
This Headphone can be used as a regular Wired Headphone by connecting your
Audio Source with the Line-In Cable to the Headphone Jack shown below.
WARNING
- Never attempt to recharge conventional dry cells.
- Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.
- Never use another type of battery or non-rechargeable batteries to replace the rechargeable (LR03/ AAA) batteries supplied. When the headphones are not in use, switch it OFF to avoid damaging the batteries.
- Prolonged exposure to Excessive sound pressure from earphones and headphones may cause permanent hearing loss.
TROUBLESHOOTING
No Sound
- Ensure the AC/DC adaptor is fully inserted into the AC outlet and the power connection input on the Transmitter.
- Ensure the Power Button at the back of Transmitter is switched to ON.
- Ensure the headphone is switched ON.
- Headphone battery charge level may be too low, recharge the batteries fully.
- Ensure the TV or the connected audio device is switched ON.
- The volume of headphone may be too low, adjust the volume to a moderate level.
- The audio signal input level is too low. Increase the volume of the audio source.
Distortion
- Ensure the volume level of headphone is set to an approximate level.
- The headphone is too far from the transmitter, move it closer.
- The audio signal input level is too low. Increase the volume of the audio source.
SPECIFICATIONS
-
Transmission mode: Digital Hopping System
Carrier frequency: 2.4GHz -
Operating voltage: Transmitter 5V
Receiver 2×1.2V AAA -
Frequency response: 20 Hz – 20 KHz
Work Time: 12 hours -
Charge Time: 4-6 hours
Distortion: 0.5% -
Signal-to-noise ratio: 85 dB
Range: Up to 30 meters
FCC Rules
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
ARTISTE TECHNOLOGY LTD.
The 6th Building, No. 173, Dunhe Road, Haizhu District, Guangzhou, Guangdong,
China Http://www.artiste-audio.com
Tel: 86-20-66319168
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>