HOMMAK IC1550 Wireless Indoor and Outdoor Humidity and Temperature Monitor User Manual

HOMMAK IC1550 Wireless Indoor and Outdoor Humidity and Temperature

Monitor

INTRODUCTION

WARNINGS

• The remote sensor is rain-proof, but it must be always.
• placed upwards to avoid rain getting inside through the vents on the bottom, making it detect the environmental temperature and humidity more precisely and quickly.
• This device contains electronic components (power supply and/or batteries). Do not let children use the device alane to avoid accidents. Refer to the manual to use the device.
• Only use the dry cloth to clean the exterior of the device, do not use any deterget or immerse it in water to avoid damaging the electronics.
• Do not charge the battery by using any other methods

OPERATION INSTRUCTIONS

1. Open the battery compartment of the base station as picture shows, and insert AAA batteries, Press the “F/C button on the base station to switch between C and °F, press CH/SYNC to choose the channel.

2. Open the battery compartrment of the remote sensor and insert AAA batteries. Choose the same channel of the base station. Press TX button to sync, and then the temperature-humidity detected by the remote sensor will be displayed on the base station.

3. Installation Tips: please try the following tips if the base station fails to connect with the remote sensor

4. Long press the CHANNEL/SYNC button on the base station for 3s, and then press TX button on the remote sensor Relocate the base station or the remote sensor until they are connected.

5. Signals from other electronic devices may cause inter ference, please place the base station and the remote sensor away from these devices. The remote sensor may not function properly in extreme conditions. Reinstall the
   batteries and the device will operate properly under normal weather conditions

6. If the base station is attached to a refrigerator or a metal surface, the transmission distance maybe shorter. Keep it away from magnetic objects or place the base station and remote sensar as close as possible.

SPECIFICATIONS

1. 433MHztransmisslon frequency,
2. Transmission range is up to 200ft. (range may be shortened by interference)
3. Components:
   • 1Base Station (Receiver)
   • 1 Remate Sensor (Transmitter)
   • 4 AAA batteries

FUNCTIONS OF BASE STATION (RECEIVER)

1. LCD Display: 3.5inch, display the current outdoor/indoor humidity and temperature

2. Indoor Temperature Range: -20°C-70*C (4’F-158 F).
   The display shows LLL or HH.H when the temperature is out of range.

3. Temperature Accuracy:
   0.0-50.0 C(32.0″F-122.0P); +1,0*C(#1,8″F)
   Others: 12C (13.6’F)

4. Indoor Humidity Range: 1h-99%

5. Humidity Accuracy¥
   20.0°C-26.0’C (68.0°F-78.8°F): 306-80% (+5%)
   Others: :89%

6. Update Time: 10s

7. Temperature Resolution: 0.1C/

8. Humidity Resolution: 1%

9. Mounting Way: Table Stand

10. Power Supply: AAA batteries’2

BUTTONS

1. Press once to turn on the backlight. The backlight wil automatically shut off after 10s; press the button again within 10s to tum off the backlight.
2. °F/C: Press the button to switch between Celsius and Fahrenheit
3. CH/SYNC: Press the button to switch channels press and hold the button to enter the synchronization mode.
4. ALL Time/MAX/ MIN: Press to switch the MAX and MIN temperature/hurmidity records of ALL TIME; Long press for 3s to clear the history data.
5. 24HRS/MAX/ MIN: Press to switch the MAX and MIN temperature/humidity records of 24 HRS; Long press for 3s to clear the history data,

TEMPERATURE &HUMIDITY TREND

1. Indicates the temperature and humidity are in an increasing trend.
2. Indicates no change in temperature and humidity.
3. Indicates the temperature and humidity are in a decreasing trend.

COMFORT LEVEL INDICATOR

• Comfort: 40%-7O9%
• Dry: less than 40%
• Wet: more than 70%

FUNCTIONS OF REMOTE SENSOR (TRANSMITTER)

1. Outdoor Temperature Range: 58F-158″F (50’C-70C)
   Display LLL or HH.H when the temperature is out of the range.

2. Humidity Range: 16-999%

3. Power Supply: AA batteries 2

4. Wall-Mounted Design: Always keep the remote sensor upwards to avoid rains getting in, make sure that air car circulate through the air vents on the bottom.

BUTTONS

1. CHANNEL 12,3: 5lide to set the channel 1,2 or3.
2. RESET: Short press to reset the transmitter.
3. TX: Short press to send temperature and humidity data to the receiver.

NOTE
When replacing the batteries (either for base station or remote sensor), or the base station and remote sensor are losing connection, please follow the below steps to re-connect the base station and remote sensor

1. Place the remote sensor and the base station as close as possible.
2. When pairing: Tflashes for 3 minutes
3. If Tdoes not flash after 3 minutes, please press the CH/SYNC for 3s until the Flashes
4. Press the TX or RESET button, the temperature and humidity detected by the remote sensor will be displayed on the base station.
5. Please trepeat the pairing steps above if you have other transmitters to connect. One base station can only pair with up to 3 transmitters.
6. If you paired more transmitters with the base station, please press CH/SYNC button to select the channel of each.
   There are 4 channel modes: CH1, CH2, CH3, C. Gmeans that the device will automatically switch the channel, changing from one channel to another channel every 5s.

CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To retum your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.

FCC STATEMENT

Any changes or modifications not expressly approved by the party responsible for cornpliance could void the user’s authority to operate the equipment This device complies with part 15 of the FCC Rules. Operation is subject to the following two condrtions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide a reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is rno guarantee that interference will not occur in a particular installation, If this equipment does cause harmful interference to radio or television reception, which can be deterred- mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit diferent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.This equipment should be installed and operated with minimum distance 20cm between the radiator& your body

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>