Cameron AMZ20PT Outdoor Pan and Tilt HD Camera User Guide
- June 5, 2024
- Cameron
Table of Contents
Cameron AMZ20PT Outdoor Pan and Tilt HD Camera User Guide
Getting Started
In the Box
-
Pan & Tilt Camera with mounting bracket
-
Screws and Anchor Kit
-
Antenna
-
Allen Wrench
-
RJ45 Connector
-
AC Power Adapter
-
Quick Start Guide
What You Will Need: Philips Screwdriver, access to circuit breaker, 2.4GHz Wi-Fi network, network name and password.
Hmmm… where should I position Cameron? Knowing where to place your pan ‘n tilt camera is very important for optimal surveillance
When Considering Locations
DO
- Position in vulnerable areas such as: Front Door
- Back & Side Doors
- Garage & Driveway
- Interior Common Areas
DON’T
- Position camera in ways that violate your neighbor’s privacy –
- Install in areas inside where there is a warranted expectation of privacy, such as bedrooms and bathrooms
For Outdoor Installation
DO
- Install camera 8-10 feet from the ground
- Protect Camera from direct exposure to the elements
DON’T
- Point camera directly at the sun, it causes glares and high contrast
- Position camera where rain gutters, trees and heavy foliage can obstruct views
For Indoor Installation-
DO
- Take advantage of corners to provide largest possible vantage point
- Angle for indirect light
DON’T
- Position camera directly toward light sources
- Point camera directly at windows as it can cause reflection issues
Location of Controls
INSTALLATION INSTRUCTIONS
- Device Setup
Download the Cam Sees App and open it. Use the Set Up Wizard to connect to your Wi-Fi network and follow the steps to finish installation.
It is highly recommended to set up your camera to Wi-F1 before installing it in its final location.
-
Screw the Antenna clockwise into the rear of the camera. Secure the multi-position
-
Camera Bracket to a stable surface or wall using the four screws. If needed, four anchors are also included. It should be look’in good.
-
Connect the small end of the AC adapter to the camera’s AC-in Plug located at the end of the bracket. You’re almost there.
-
Plug into electrical outlet when ready to install Cam Sees App.
-
To Set the Camera’s Home/Default Point: Position the camera where you want for the Home position.
-
Tap the PTZ icon, then 1 Save. You can add up to two more pre-programmed points. There – you did it!
Tip
- After camera is successfully connected to Wi-Fi,
-
- unplug camera power,
- mount camera using multi-position bracket,
- screw in antenna and
- plug back in to power. Camera will power on and still be connected to Wi-Fi.
App Download & Wi-Fi Connection
-
From your smart device or tablet, DOWNLOAD and INSTALL the free Cam Sees App.
-
Add antenna and plug camera into an electrical outlet (allow the camera up to 90 seconds to start up).
-
Now, LAUNCH the Cam Sees App and the Setup Wizard will appear.
-
Tap to start the Wizard and then tap Add Device.
-
Tap New Device and the unit will start searching.
NOTE: If the mobile device’s Bluetooth is not turned on, a message will appear requesting to have the Bluetooth setting turned on. -
Select your home network from the menu, and then enter your home network’s Wireless Password.
If you get an error, make sure to enter the correct password and repeat. -
At the next screen enter a New Password/ Security Code twice. Tap SAVE.
TIP: Remember to write down your new password and save it somewhere safe and easy for you to access. -
Tap the PLAY icon or preview picture for live video.
Good stuff to know
-
Tap Snapshot icon to save image to camera roll or gallery
-
Tap to Record to MicroSD card (pre-installed)
-
Tap and hold Microphone icon to talk, (sound comes through video camera’s speaker)
-
Tap Settings icon from home page to access Advanced Settings and Customizing Features.
The default admin password is 123456 -
Tap to turn volume ON or OFF in Live View Mode
-
PTZ button (Pan & Tilt) allows user to set 3 preset positions for the camera to move to (includes Home position). -
Smart motion detection push notification alerts -
Tap to RETURN icon to go back to main page
-
Tap to EVENT icon to review recorded files.
NOTE: Screen shots and icons may vary due to continuous updates to App and software development.
CAUTION: Do not submerge camera in water. STRANGULATION HAZARD: Infants
have strangled in power cords. Keep power cords more than 3 feet away from
cribs. When using your equipment, always follow basic safety precautions to
reduce the risk of fire, electric shock and injury to persons. Illustrations
are for reference only. Actual product specifications may vary.
For additional precautions and product information, please see owner’s manual
at CameronCameras.com
FCC Compliance Statement:
This device complies with Part 15 of the FCC rules. Operation is subjected to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
For detailed installation and setup, please refer to the Model AMZ2OPT complete User’s Guide available on our website.
Cameron Cares
CUSTOMER SUPPORT
at 1-800-275-9381 or email
info@cameroncameras.com
CameronCameras.com
meet Cameron
Cameron sees EVERYTHING in range of your outdoor space, even when you can’t.
Alerts to your smart-phone or tablet are sent when activity is detected. So
you never have to worry when Cameron is on pan & tilt patrol.
CameronCameras.com
Model AMZ2OPT
Distributed by Atoms Labs LLC ©2020 Atoms Labs LLC, Flower Mound, TX. All rights reserved. App Store logo is a registered trademark of Apple, Inc. Google Play logo is a registered trademark of Google, Inc. Amazon Appstore logo is a registered trademark of Amazon. Certain other product names, brand names, and company names may be trademarks or designations of their respective owners.
FCC Compliance Statement:
This device complies with Part 15 of the FCC rules. Operation is subjected to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>