Sine Audio PA300 Power Amplifier User Manual
- June 5, 2024
- Sine Audio
Table of Contents
by Sine Audio
Power Amplifier
User Manual
PA300 / PA400 / PA500 / PA600
PA310 / PA410 / PA510 / PA610
Warranty information
The warranty period for this product is 12 months from the date of its
original purchase. If manufacturing defects occur, please contact your dealer
at the first time, we will instruct you on how to return the defective unit
back to us for repair or replacement.
The following are excluded from the Sine Audio warranty coverage:
Product over warranty.
Damage resulted from misuse and abusive action.
Damage resulted from chemicals, fire, radioactive substances, poison, or
liquid.
Damage resulted from a natural disasters.
FCC information
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:(1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of more
of the following measure:
→ Reorient or relocate the receiving antenna.
→ Increase the separation between the equipment and receiver.
→ Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
→ Consult the dealer or an experienced radio/TV technician for help.
→ This device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
Unpacking
→ Remove all packaging and check for the presence of all parts and for
transport damage. In case of damage or incomplete delivery, please contact
your dealer.
→ Please keep the packaging. The system can be stored in it, if not used for a
longer period of time.
→ Make sure the power adapter is disconnected from the electrical outlet
before making any mounting and connection.
→ During operation, if the cables require to be reconnected, the power
adapter must be disconnected first, otherwise damage to the system may result.
Package Contents
| PA300： | PA400： |
|---|
1 x Power amplifier
1 x Power adapter
1 x Audio cable
1 x User manual| 1 x Power amplifier
1 x Power adapter
1 x Optical cable
1 x User manual
Features
→ Stereo class D power amplifier
→ Gold Plated Speaker Banana Jacks
→ Aluminum alloy housing
→ 3.5mm headphone output and line out interface (PA310 PA410 PA510 PA610)
→ Stream music from smartphone or tablet
→ Analog audio interface ( AUX input )
→ Digital audio interface ( optical and coaxial input, PA400/PA600)
→ Tone control (bass, treble PA500/PA600) and volume control
Specifications
Power adapter
Input: 100-240VAC 50/60Hz
Output : 22.5V / 3.2A OCP : 7.1A
Power amplifier
Output power：80W per channel
Matching impedance: 4-8 Ω
Frequency Response: 20Hz – 20KHz
Total harmonic distortion: 0.04%
Signal to noise ratio:96dB
Digital audio interface: optical and coaxial
Digital audio sampling rate: 192KHz / 24bit
Headphone output
Output power: 125mW X 2 ( 32Ω load )
Matching impedance: 16-200 Ω
Total harmonic distortion：0.001%
Signal to noise ratio：98dB
Note: Accessories and specifications are subject to change without
notice.
System Overview
PA300 PA310 (PA500 PA510 With Bass Treble Control)
→ Switch to BT: Blue indicator light flash.
→ Switch to AUX: Blue/green indicator light stay solid
→ Headphone Jack(3.5mm) is only for PA310 and PA510
→ Switch to AUX/RCA to enter the AUX or RCA input mode.
→ Switching to AUX/RCA may enter AUX input mode when the AUX audio cable is
plugged in, you need to switch to OFF and switch to AUX/RCA again to enter RCA
input mode.
→ Please turn off the power amplifier first, connect the audio input and speaker cable, adjust the volume to half, and then turn on the power amplifier after connecting the DC power supply.
> > PA400 PA410 PA600 PA610
→ Switch to BT: Blue indicator light flash.
→ Switch to AUX: Blue indicator light stays solid.
→ Switch to COAX: Green indicator light stays solid.
→ Switch to OPT: Red indicator light stays solid.
→ Headphone Jack(3.5mm) is only for PA410 and PA610
→ Bass treble control is only for PA600 and PA610
→ Switch to COAX/OPT to enter the digital audio input (coaxial or optical)
mode.
→ Switching to COAX/OPT may enter one of the digital audio input (coaxial or
optical) modes, you need to switch to OFF and switch to COAX/OPT again to
enter the other
digital audio input (coaxial or optical) mode.
→ Please turn off the power amplifier first, connect the audio input and speaker cable, adjust the volume to half, and then turn on the power amplifier after connecting the DC power supply.
Bluetooth function
External Bluetooth devices can be connected to the amplifier via Bluetooth
connection.
- Switch to BT to enter the Bluetooth mode. The Bluetooth indicator lights up blue.
- Activate the Bluetooth function of the external device and search for Bluetooth devices.
- Select the amplifier (SineAudio Amplifier) from the Bluetooth device list.
- Follow the instructions shown on your device’s screen.
> Disconnecting the Bluetooth device:
→ PA300/PA500
→ You can also use the Bluetooth device to disconnect the Bluetooth
connection. The amplifier starts searching for another Bluetooth device.
Notes:
→ If you cannot pair your Bluetooth device, you may need to remove the
amplifier from the pairing list and try pairing again.
→ Bluetooth works best within a range of up to 33 feet (10 meters).
→ The music streaming may be interrupted by obstacles between the Bluetooth
device and amplifier, such as walls, the metallic casing that covers the
device, or other devices nearby that operate at the same frequency.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This device and its antenna(s) must not be co-located or operated in
conjunction with any other antenna or transmitter.
Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirements in
portable exposure conditions without restriction.