MOVCAM MRW-1 Helm Wheels Multifunctional Remote Controller with High Precision User Manual
- June 5, 2024
- MOVCAM
Table of Contents
HELM|Wheels
User Manual
V 1.0
MRW-1
Contents
Helm wheels is a multifunctional remote controller with high precision. It
offers both wired and wireless control over Helm remote head and another
third-party 3-axis stage. Helm wheels offer real-time data synchronization for
better control.
The wheels share almost the same parameter structure and keyboard layout as
that of the Helm remote head, which makes it easier for users to operate.
What’s more, operators can rearrange the composition of the master wheels
according to their own preference and for a more flexible configuration.
The wheels is powered via a V-mount battery which is convenient and easy to
change on set.
The wheel employs a 2.4GHz wireless connection and built-in wireless modules.
It’s highly anti-jamming with long-distance transmission. MBUS port provides
wired control.
There are 1/4” threaded holes for external accessories like monitors.
Learn about HELM Wheels
1、Handle
2、Sensitivity Knob
3、Display screen
4、Deadband Knob
5、Indicator light
6、Angle Lock
7、Reverse/switch| 8、Speed Adjust knob
9、Tighten Knob
10、Base plate
11、Switch/Confirm Knob
12、Detachable module
13、Wheel
---|---
Control Panel
1 Deadband
2 Pause
3 indicator light
4 Mounting mode switch button
5 Camera REC
6 Return
7 Multi-function button| 8 Sensitivity
9 Recenter
10 Play/stop
11 Follow mode switch button
12 REC
13 Enter
14 Display screen
---|---
| |
---|---|---
1 Antenna
2 3/8″ threaded holes
3 1/24″ threaded holes
4 DC OUT
5 MicroSD card slot| 6 MBUS port
7 Power switch
8 Battery release
9 Base plate
10 Battery mount
---|---
Operators can rearrange the composition of the master wheels according to their own preference and for a more flexible configuration.
|
|
---|---|---
Parameter setting
After balance adjustment, use the control panel to set up Helm. Helm can also
be controlled via an external controller like the wheel controller.
Power up Helm before starting setup.
- Press the Switch/Confirm Knob to enter the setup menu. Turn the knob to choose the entry for setup.
- When an external controller like the wheel is used to do setup, the first step is to enter the System to set the wireless channel. Set both the channel on the control panel and that on the wheel control at the same one. Connection is successful when the sign appears on the upper right corner of the screen.
- Motor stiffness and strength can be set via Motor entry. Under Smoothtrack mode, motor speed, Deadband, and sensitivity can be set.
- Under Remote entry, Deadband, max speed, and smoothing can be set. The data sources can also be set.
- Under System entry, the following can be set: wireless, calibration, and language.
HELM remote-controlled stabilization head
MRW-1
FCC Caution：
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
Movcam Tech. Co., Ltd
F4-Bld2, Google SciencePark,#1 Lirong Road,
Longhua New District, Shenzhen,518109, CHN
Tel：+86 755 2658 0888 Fax: +86 75526580999
Email：[email protected] P.C.：518109
www.movcam.com