NASA WS500 Weather Station with Outdoor Sensor User Manual

: June 5, 2024
: NASA

NASA WS500 Weather Station with Outdoor Sensor

NASA WS500 Weather Station with Outdoor Sensor PRODUCT

PLEASE READ ALL THE DIRECTIONS IN THIS MANUAL CAREFULLY AND FOLLOW THE OPERATING AND SAFETY INSTRUCTIONS. KEEP THIS MANUAL FOR FUTURE REFERENCE AND SHOW IT TO POTENTIAL USERS.

SAFETY INSTRUCTIONS

Keep children away from packaging materials (plastic bags, rubber bands, etc.)
This unit may be used by children aged 8 years and over and by anyone with reduced physical, sensory or mental capabilities or a lack of experience and knowledge, provided that they have been given supervision or instructions about how to use the unit safely and that they understand the hazards involved.
Never allow children to handle the unit without supervision.
Cleaning and maintenance must not be carried out by children unless they are over 8 years of age and supervised.
Do not use the unit outdoors.
Do not disassemble the unit.
Do not immerse the unit in water.
Do not expose the unit to bumps, vibration, dust, or extreme humidity. This could lead to malfunctions, short circuits or damage to batteries and components.
Do not expose the unit to direct sunlight, flames or high temperatures.
Do not expose the unit to dripping water or splashes.
Do not use the unit if it does not operate normally
Do not repair the unit yourself. Only allow repairs to be carried out by a qualified person.
This unit has been designed for domestic use only. The manufacturer cannot be held responsible, and the guarantee will not apply, for any professional use that is not appropriate or does not comply with the instructions.
The unit may only be used as described in this manual.

BATTERY INFORMATION

To function properly, the unit must have the appropriate batteries inserted.
Only the recommended type of batteries should be used.
The batteries must be inserted the right way round.
The battery terminals must not be short-circuited.
Do not mix new and used batteries.
Do not mix alkaline, standard (carbon-zinc) and rechargeable (nickel -cadmium) batteries.
Do not recharge the batteries or attempt to open them.
Do not dispose of batteries in fire.
Remove the batteries from the unit when not in use for a long time.
Replace all batteries at the same time with new, identical batteries.
If the liquid from a battery comes into contact with your eyes or skin, wash the affected area immediately and thoroughly with clean water and seek medical attention.
Do not expose batteries to excessive heat such as sunlight, fire or similar.
DESCRIPTION

Weather station
LCD screen
Indoor temperature
AL button (AL1 and AL2 alarms selection)
Humidity
DOWN button + temperature unit change (C°/F°)
Outdoor temperature
Day of the week
SNZ button (snooze) + screen lighting
Date DD / MM
Clock (hours, minutes, seconds) /Alarms
CH button (outdoor sensor connection)
UP button + AL1 and AL2 alarms activation
TIME button
Current weather
Stand
AC adapter socket
Batteries compartment

FUNCTIONS

Weather forecast: sunny, sunny but cloudy, cloudy, rainy
Time display: 12/24 hours
Display of the date (DD/MM) and the day of the week (available in 7 languages)
Alarm and snooze function
Indoor temperature (0°C ~ +50°C) with 1°C detection accuracy
Outdoor temperature (-30°C ~ +70°C) with 1°C detection accuracy
Temperature unit switching: C° / F°
Indoor humidity (25%-95%) with 5% detection accuracy
Connection possible with three external sensors
Color backlighting

POWER SUPPLY

WEATHER STATION

With 3 x AAA / LR03 1,5 V batteries (not included):

Carefully open the batteries compartment cover.
Insert 3 x AAA 1,5V batteries, taking care to follow the polarity indicated.
Close the batteries compartment.
With the USB power cable (supplied):
Connect the USB power cable to the AC adapter socket (17) on the back of the weather station and plug it into an external power source to ensure constant display backlighting.

SENSOR

Open the batteries compartment cover on the back of the sensor.
Place the small black slider at the bottom of the batteries compartment on one of the sensor’s signal transmission channels (1/2/3).
Insert 2 x AAA 1,5V batteries (not included), respecting the polarity indicated.
Close the batteries compartment cover. A red light on the front of the sensor will then flash every minute.

INSTALLATION / USE

INSTALLATION WEATHER STATION

Open the stand on the back of the weather station.
Place it on a flat horizontal surface.

SENSOR

The sensor can be installed:

either on the wall using a screw (not included). Hang the sensor through the hole on the back.
or horizontally
To connect it to the weather station, proceed as follows:
Press the (CH) button to select the transmission channel on which the slider within the batteries compartment of the sensor has been placed.
Press and hold the (CH) button for 2 seconds to start searching for the sensor signal. The corresponding indicator will then flash on the display for 3 minutes to indicate that it is being detected.
Once the connection is established, the indicator will stop flashing and the outdoor temperature reading will appear on the display.
NOTE:
if no signal can be detected, the weather station will automatically restart a search the next hour. If it fails to detect the sensor signal after several attempts, press and hold the (CH) button again for 2 seconds to reset the search. Also note that it is necessary to reconnect the sensor each time the weather station is powered off.
For best results:
Do not expose the sensor to direct sunlight or moisture.
Do not place the sensor more than 10 metres away from the weather station.
Minimize obstacles (doors, walls and furniture) between the sensor and the weather station.
Keep the sensor away from metal or electronic objects.
USE OF THE WEATHER STATION

WEATHER INDICATOR

When the unit is turned on, the weather station will show the weather conditions in the form of icons:

Sunny
Sunny but cloudy
Cloudy
Rainy

TEMPERATURES AND HUMIDITY

The weather station displays the following information:

Indoor temperature (3) and humidity (5) measured by the weather station
Outdoor temperature (7) from the sensor
NOTE:
this data is updated every 30 seconds except when the alarm sounds.
CHOICE OF TEMPERATURE UNIT
Press (DOWN) button to select the temperature unit: °C (Celsius) or °F (Fahrenheit).

SETTING THE DATE AND TIME

Press the (TIME) for 2 seconds to enter the date and time setting mode.
The first data to be set is the time display format (12/24 Hr).
Use the (UP) and (DOWN) buttons to adjust the values.
Press the (TIME) button to confirm and then move to the next data setting whose display will flash.
The setting order is as follows: hour → minute → year (Yr) → month (M) → day (D) → day of the week display language (DAY: GE / FR / IT / DU / SP / DA / EN)
At each setting, use the (UP) and (DOWN) buttons to adjust the values and press the (TIME) button to confirm.
If the buttons are not pressed within 10 seconds, the unit automatically exits the date and time setting mode and saves the last selected values.

SETTING THE ALARM

Press the (AL) button twice to select one of the two alarms (AL1 or AL2) and then press this button again for 2 seconds to set it.
The first data to be set is the hour.
Use the (UP) and (DOWN) buttons to adjust the values.
Press the (TIME) button to confirm and then move to the minutes setting.
If the buttons are not pressed within 10 seconds, the unit automatically exits the date and time setting mode and saves the last selected values.

ACTIVATING / DEACTIVATING THE ALARM

Press the (UP) button to activate or deactivate one of the two alarms. The symbol of the activated alarm will then be shown on the screen.
NOTE:
by pressing the (UP) button three times, it is possible to activate both alarms.
STOPPING THE ALARM
The alarm is triggered at the programmed time and sounds as follows:
0-10 seconds: 1 BEEP per second
10-20 seconds: 2 BEEP per second
20-30 seconds: 4 BEEP per second
beyond 30 seconds: continuous BIP
To stop the alarm, press the (UP) button; it will sound again the next day at the same time.
SNOOZING THE ALARM (SNOOZE)
When the alarm sounds, press the (SNZ) button if you want to delay it: the Zz symbol flashes and the alarm stops. The alarm will sound again after 5 minutes.
Then press the (UP) button to deactivate the alarm snooze.

BACKLIGHTING

If the weather station is plug into a power source with the supplied USB cable, the screen backlight will be constant.
If it is powered by batteries, the screen backlight is turned off to save energy. It is necessary to press the (SNZ) button to activate it for 5 seconds.

CLEANING AND MAINTENANCE

Before cleaning the unit, disconnect the power supply.
Only clean the outside of the unit and use a dry cloth. Do not use cleaning fluids to avoid damaging the electronics.