Shenzhen Shiwinka Technology SCO-M-EAS-315 Self-Checkout Kiosk Installation Guide

Shenzhen Shiwinka Technology SCO-M-EAS-315 Self-Checkout Kiosk

What is in the package

1. Box 1 includes ( 1 ) a base, ( 2 ) a pole, 3 & 4 base covers, 5 and a scan station counter support, It also includes various A, B, C1, C2, D, E, and F types of screws, bolts, and tools.
2.  Box 2 includes 6 scan station counters, 7,8,9, and 15 shopping bag holders, 12 handheld scanner holders, 13 pin pad holders, and 14 lower back covers.
3. Box 3 includes 10 a screen, 11 a camera, 16 a power cord, 17 two keys to the host 18 , two keys to the printer, and 19 a wireless handheld scanner.

Note: pinpad and network cable are not included in the package.

• Bolt : MSX16 hex bolt
• Screw(!1): M3X6 flat-head screw
• Screw II’!I: M4X6 flat-head screw
• Screw IJ3: M4X6flot·head screw with gasket Screw 11!) : M4Xl0 flal•head screw
• Boi: M8X70p.ansion boll & nut

How to assemble the main part of the self-checkout kiosk

1. Place on top of (with six [AJ bolts using torque tool A.

2. Join 3 and with two B screws, and then place them onto (2) with another two B screws using screwdriver B.

3. Install to with eight A bolts using torque tool A.

4. Place on top of ) with eight A bolts.

5. Attach O to the underside of G)with six screws using screwdriver B

6. Attach 8 to () with three C2 screws on the back and threeC2 screws at bottom using screwdriver B

7. Pluginto with four screws using screwdriver . Then place on top of (8) with four D screws.

8. Place on top of with eight A bolts using torque tool A How to assemble the accessory
   devices of the self-checkout kiosk

9. Attach to the right side of 1 with three Dscrews using screwdriver B.

10. Attach42to the left side of 1 with three Dscrews.

11. Pass the USB cable of 13 through the hole at the top of. Place on top of D with three Escrews using screwdriver E

12. Adjust the screws on12 for the wireless scanner19 if needed. Adjust the screws on 13 for pinpad if needed.

13. Use one D screw to attach the wireless scanner holder onto the left side of 1
    How to connect cables

14. Unlock the back cover using the included key.

    • Connect the cables according to the diagram.
    • The red line indicates the power cord 19 of the screen.
    • The green line indicates the power cable of pinpad (not included in the package.)
    • Yellow line 1 indicates the USB cable for pinpad (not included in the package.)
    • Yellow line 2 indicates the USB cable for the camera(1).
    • The cyan ine indicates network cable (not included in the package).
    • Except for yellow line 2, pass the other cables through the oval hole at bottom of the back cover to the end of the pole.

15. Find the wireless scanner cable in the screen and pass it through the hole on the left side of the screen. Then, connect it to the wireless scanner holder(19. (The blue line indicates the scanner cable.) After connecting the cables, lock the back cover using the included key 1.

16. Take the power cables, USB cable, and network cable out of the bottom hole on the back of the pole 2). Attach1 to the bottom hole of 2 with three Dscrews
    How to bolt the self-checkout kiosk to floor.
    Warning!
    Please bolt the self-checkout kiosk to floor using the included expansion bolts. Otherwise, it may tip over causing damage and/or injury.
    Part F: How to turn on/off the self-checkout kiosk.
    Warning!
    Please make sure the equipment is grounded before turning it on. Otherwise, it may cause electric shock or damage to the equipment.
    Part G: How to change printer paper.

17. Put the self-checkout kiosk in a desired position. Mark the drill positions of the base )on the floor. Move the kiosk aside. Drill to two inches depth. Hammer four F expansion bolts & nuts into the holes. Bolt the nuts tight first. Then unbolt the nuts and take the nuts and gaskets off. Align the holes with the kiosk. Bolt the kiosk to floor with the nuts and gaskets using torque tool E Assembly of the equipment is now complete.

18. Plug the power cord 16 of the screen and the power adapter of the card reader into UPS outlets. Plug the network cable into a network port.
    Open the clamshell door on the back cover using the included key4to find the switch. Turn on/off the switch. (“1” is for on and “0” is for off.) ****

19. Insert the printer key (19 to the printer locker and turn the key clockwise to open the door. Place new paper or replace the paper in the printer. Leave the end of the paper roll outside the door and make sure the
    paper roll comes out from its top. Push to close the door.
    If the blue light turns on, the printer is ready to work. Otherwise, please check the above process to ensure the paper is placed and the door is closed properly.

FCC Warning

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged tO try to correct the interterence by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement
This equipment complies with radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>