REDATOM RED-DAC-1X2 HDMI 2.0 Audio Extractor User Manual
- June 5, 2024
- REDATOM
Table of Contents
REDATOM RED-DAC-1X2 HDMI 2.0 Audio Extractor User Manual
Introduction
The RED-DAC-1X2 is a digital and analog audio extractor that includes a 18Gbps
HDMI 2.0b splitter. The product is designed to extract audio from video
sources for flexible integration plus seamless integration between a single
input and two display devices. Featuring full 4k60 HDR, High Bit Rate Audio
support, EDID and CEC passthrough, the RED-DAC-1X2 simplifies the process of
adding an additional HDMI display device to your system.
The RED-DAC-1X2 offers flexibility for installations that require audio
extraction and for your next bar, restaurant, digital signage, commercial or
residential installation.
Features:
- HDMI DAC with Analog and Digital out and HDMI Passthrough
- 4K 2-Way HDMI Splitter
- One HDMI in, Two identical HDMI out
- Full HDMI 2.0b Support
- Supports up to 18Gbps with resolutions up to 4K60 4:4:4
- CEC Passthrough (HDMI Output 1)
- EDID Passthrough (HDMI Output 1)
- Mounting ears included for easy installation to walls or furniture
Specifications
Video:
- Video Resolutions: Up to 4K60 4:4:4
- VESA Resolutions: Up to 4096X2160 (DCI 4K)
- Chroma Supported: 4:4:4, 4:2:2, 4:2:0, RGB (Limited and Full)
- Deep Color: Up to 16 Bit (1080p) Up to 12 Bit (4K)
Audio:
- LPCM (Up to 192KHz 24 bit): 2.0, 5.1, 7.1
- Dolby: Dolby Digital, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos
- DTS: DTS 6.1 ES, DTS HRA, DTS Master Audio, DTS:X
- Analog (Stereo RCA): 2CH PCM 20-20,000Hz
Dimensions:
- Block Size: 4.75″ x 3.125″ x .75″ (WxLxH)
Included in the Box:
- Audio Extractor with HDMI Splitter
- Power cord
- Mounting brackets
Panel Descriptions
Front Panel:
- SERVICE USB input — For service & firmware updates only; Do not use.
- HDMI IN input
- HDMI LED activity display
IN
Light On — Unit has sync with an HDMI source device Light
Off — Unit is not synced with an HDMI source device
OUT 1
Light On — Unit has sync with an HDMI display device Light
Off — Unit is not synced with an HDMI display device
OUT 2
Light On — Unit has sync with an HDMI display device
Light Off — Unit is not synced with an HDMI display device
Back Panel:
- HDMI OUT1 output
- HDMI OUT2 output
- TOS — TOSLINK output
- RCA OUT — L/R and COAX output
- DC/12V — power supply input
Connections and Operations
- Connect the HDMI input source into the RED-DAC-1X2 HDMI IN input
- Connect the HDMI from the displays into the RED-DAC-1X2 HDMI Out1 and HDMI Out2
- Insert the DC end of the power supply into the RED-DAC-1X2 and then plug the AC side of the power supply into the power outlet
- Connect preferred audio output 5. The unit automatically powers up when plugged in
Connection Diagram:
Troubleshooting
No power
- Ensure DC power supply is inserted fully and tightened completely.
No HDMI IN LED
- Ensure HDMI cable lengths are less than 10 Meters (~33ft)
- Ensure Source Device’s resolution is a maximum of 18Gbps or 4K60 4:2:2/4:4:4 8Bit
No HDMI OUT1/2
- Ensure HDMI cable lengths are less than 10 Meters (~33ft)
- Ensure Source Device’s resolution is a maximum of 18Gbps or 4K60 4:2:2/4:4:4 8Bit
- Ensure that HDMI Display Device is powered on
- Ensure that HDMI Display Device on HDMI Output 1 is not in 8k enhanced or HDMI 2.1 Mode
Analog Audio Outputs Issues
- Audio is clicking — Ensure PCM audio is being sent, Bitstream Audio (DD/DTS) is not supported by analog audio output
- No Voices — If the source is sending multichannel PCM, center channel will be ignored. Set source to send stereo audio
Digital Audio Outputs Issues (TOS + COAX)
- No Audio — Ensure that TOS light is on (RED Internal), if enabled and no audio is being played, try source to PCM. Digital audio outputs do not support High Bit Rate Audio
Warranty Information
- This warranty applies to US Residents who purchase from an authorized RED ATOM Dealer. RED ATOM media distribution products are covered against defects in materials and workmanship for 1 year from date of purchase.
- Within the warranty period, RED ATOM will repair or replace the defective component or product, at its sole discretion.
- For warranty service: — For RED ATOM media distribution products that were professionally installed, contact your installer directly. — For all other service requests, contact RED ATOM at info@redatomproducts.com.
- For all warranty service requests, you must supply a copy of your original receipt and installation service order if applicable. If your product must be shipped to RED ATOM for inspection, you will be responsible for the shipping charges. For warranty replacements, RED ATOM will ship product back to you for free.
- RED ATOM disclaims any liability for modifications, improper installations, accidental damage, or failure to follow care instructions provided by RED ATOM. To the maximum extent permitted by law, RED ATOM disclaims any other warranties, expressed or implied, including warranties of fitness for a particular purpose and warranties of merchantability. RED ATOM will not be liable for any damages arising out of the use of, or inability to use, RED ATOM. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Specifications are subject to change without prior notice.
www.redatomproducts.com
Questions? Contact us at
info@redatomproducts.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>