current ColorPLUS+ Smart LED Light Installation Guide
- June 5, 2024
- current
Table of Contents
Smart LED Light I
nstallation Guide
| Works with AquaticVita app | only supports 2.4 GHz wifi |
|---|
Getting Started
WARNING:
These products may represent a possible shock or fire hazard if improperly
installed or attached in any way. Products should be installed in accordance
with this install guide, current electrical codes, and/or the current National
Electric Code (NEC).
Download the Aquatic VITA app on your smart device
AquaticVITA app|
---|---
Install LED Light
– Slide adjustable docking legs on each side of the light fixture to match the
length of your aquarium.
– Connect the 3-pin plug on the light fixture to the matching 3-pin plug on
the LED controller,
– Connect the male DC plug from the power supply to the LED controller.
– Plug the power supply into a GFCI-protected AC outlet ensuring a drip loop
is in place.
– Place fixture over glass top of the aquarium and adjust docking mounts as
needed to fit tank.
You are now ready to use the LED light via the inline LED controller.
To activate smart mobile app features, proceed to steps 4 & 5. When in Smart
Wi-Fi pairing mode, the LED light will blink. Note: the light will stop
blinking after 3 minutes or when controlled via the inline controller.
LED Controller Button:
WARNING:
LED Controller is NOT waterproof. Keep in a dry place away from dripping water
or where it may drop into the water.
Main control features:
– Press once (1x) to turn ON, and the light will display
the default White color spectrum (all colors 100%).
– Press and hold the button for 3 seconds to turn the light OFF.
*To reset the controller for pairing with the Vita app and mobile device, press and hold the button for 9 seconds the LED light will blink red when ready for pairing and connection.
Manual Scene control:
– Press 2x to display the Sunrise fade scene.
– Press 3x to display the Sunrise fade scene.
– Press 4x to display the Moonlight fade scene.
– Press 5x to display the Rainstorm scene.
– Press 6x to display the Partly Cloudy scene.
– Press 7x to display the Sunset scene.
– press 8x to display the Glow scene.
– Press 9x to display the Stream scene.
– Press 10x to display the Deepwater scene.
Launch and use the Aquatic VITA app to complete the setup.
– Open the VITA app.
– Complete the requested information to create a new account, or sign in to
your existing account.
Tap Add Device or the + sign, then select “ColorPlus Aquarium LED” and
confirm. Then enter your Wi-Fi network & password.
The light must be rapidly blinking to connect. If not already blinking, press
and hold the button on the controller for nine seconds to put a light in
pairing mode.
Be sure to connect to a 2.4 GHz Wi-Fi network that covers your installation
location.
LED controller will then pair with your mobile device (this can take 30-60
seconds).
(OPTIONAL) Connect to Alexa or Google Assistant using the in-App guide
TROUBLESHOOTING TIPS CONNECTING TO WI-FI
If you are having difficulty connecting:
- Make sure the Wi-Fi network is a 2.4 GHz network. Smart Strip Light will not connect to a 5 GHz network.
- Test your Wi-Fi network with other devices such as your phone to make sure it is operating properly.
- The Wi-Fi connection may not have good coverage during setup. Try moving the Smart Strip Light closer to your Wi-Fi router.
For more information, check the App User Guide at www.aquaticvita.com for help. Or email us at info@current-usa.com
IMPORTANT SAFETY INSTRUCTIONS
When using electrical products, basic precautions should always be practiced
including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
- Never attempt repairs yourself, return the device to an authorized repair facility for service or discard it.
- Carefully examine light after installation and BEFORE plugging it into the GFCI wall outlet. Be sure there is NO water or moisture on the light.
- Never plug in a wet cord. If a plugged-in light or socket does get wet, DO NOT TOUCH IL Instead, promptly disconnect the fuse or circuit breaker that supplies power to the light.
- Never operate a light that is damaged or malfunctioning, discontinue use immediately and return or discard it.
- This is NOT a toy. Close supervision is required when any appliance is used by or near children.
- Always unplug the fixture when not in use, before putting on or taking off parts, and before cleaning. Never pull the cord to unplug from GFCI.
- Do not use this light for anything other than its intended use.
- Ensure the light is securely installed before supplying power to the unit.
- Do not use with an extension cord.
- Do not look directly into the LEDs.
WARNING: Risk of Electric Shock. Plug devise ONLY into a GEC! protected receptacle. If one is not provided, contact a certified electrician for proper installation. WARNING: Risk of Electric Shock. Mount the unit at a height greater than I foot from the ground surface.
SAVE THESE INSTRUCTIONS
This manual contains Important safety and operating instructions for power
units For more information. see the VITA App User Guide at
www.aquaticvita.com or visit www.current-
usa.com
WARNING:
Drip Loops should always be used to help prevent water from traveling along the cord and coming into contact with an electrical outlet. Drip loops must always be below the level of the outlet. If the plug or outlet does get wet, DO NOT TOUCH the cord. Disconnect the fuse or circuit breaker that supplies power.
GROUNDING INSTRUCTIONS
This LED system must be powered with the supplied UL/cUL Listed power
supply. To avoid possible electric shock, the power supply must be plugged
into a GFCI wall outlet that is installed and grounded in accordance with all
appropriate codes and ordinances.
LIMITED WARRANTY
Current USA, Inc. warrants this product against defects in materials and
workmanship of a period of ONE (1) YEAR from the date of original retail
purchase and is not transferable.
Warranty on all Products, including Aquariums, is limited to replacement of
the product and does not cover fish loss, personal injury, property loss, or
direct, incidental, or consequential damage arising to the use of this
product.
Note: Current-USA, Inc. One-Year Limited Warranty does not cover damage caused
by the following: improper installation, saltwater corrosion, electrical
surges, or modifications. This warranty does not apply if the product has been
damaged by accident, abuse, misuse or misapplication or if the product has
been modified without the written permission of Current-USA, Inc.; or if any
Current-USA, Inc. logos have been removed or defaced.
THE WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL
OTHERS, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED. CURRENT USA, INC.
SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING BUT NOT
LIMITED TO LOST PROFITS, DOWNTIME, GOODWILL, DAMAGE TO OR REPLACEMENT OF
EQUIPMENT AND PROPERTY, AND ANY COSTS OF RECOVERING ANIMALS, PLANTS, TANKS, OR
OTHER AQUARIUM-RELATED ITEMS AND/ OR EQUIPMENT. CURRENT USA, INC. IS NOT
RESPONSIBLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM
ANY BREACH OF WARRANTY, OR REPLACEMENT OF EQUIPMENT OR PROPERTY, OR ANY COSTS
OF RECOVERING OR REPRODUCING ANY EQUIPMENT, ANIMALS OR PLANTS USED OR GROWN
WITH CURRENT USA, INC. PRODUCTS. Some jurisdictions do not allow the exclusion
or limitation of incidental or consequential damages or exclusions of implied
warranties, so the above limitations or exclusions may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights
that vary form jurisdiction to jurisdiction.
This device Contains a Transmitter
Module FCC I D:2AN DL-CB3S
IC: 23243-CB3S
ELECTRICAL RATINGS:
INPUT: 120-240VAC,50/60HZ
OUTPUT: 12VDC,1A, 24W MAX
Supplier’s Declaration of Conformity: 47 CFR § 2.1077 Compliance
Information
Responsible Party: Current USA, Inc.
2640 Business Park Dr.
Vista, CA 92081
760-727-7011
Unique Identifier: Models: 9050, 9051, 9052
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>