ZTE 9047 Axon 40 SE Smartphone User Guide
- June 5, 2024
- ZTE
Table of Contents
SE Smartphone
User Guide
FCC ID: SRQ-ZTE9047
LEGAL INFORMATION
Copyright © 2022 ZTE CORPORATION.
All rights reserved.
No part of this publication may be quoted, reproduced, translated or used in
any form or by any means, electronic or mechanical, including photocopying and
microfilm, without the prior written permission of ZTE Corporation.
Notice
ZTE Corporation reserves the right to make modifications to print errors or
update specifications in this guide without prior notice.
We offer self-service for our smart terminal device users.
Please visit the ZTE official website (at
www.ztedevices.mx) for more information on the
user manual, self-service, and supported product models. Information on the
website takes precedence.
Disclaimer
ZTE Corporation expressly disclaims any liability for faults and damages
caused by unauthorized modifications of the software.
Images and screenshots used in this guide may differ from the actual product.
Content in this guide may differ from the actual product or software.
Trademarks
ZTE and the ZTE logos are trademarks of ZTE Corporation.
Android™ is a trademark of Google LLC.
The Bluetooth® word mark and logos are registered trademarks owned by the
Bluetooth SIG, Inc. and any use of such marks by ZTE Corporation is under
license.
microSDXC logo is a trademark of SD-3C, LLC.
Other trademarks and trade names are those of their respective owners.
Getting to Know Your Phone
Your phone supports 2.4 GHz and 5 GHz Wi-Fi.
Setting Up Your Phone
The nano-SIM card can be installed or removed while the phone is turned on.
WARNING!
To avoid damage to the phone, do not use any other kind of SIM card, or any
non-standard nano-SIM card cut from a SIM card. You can get a standard nano-
SIM card from our service provider.
-
Insert the tip of the tray and eject the tool into the hole on the card tray.
NOTE: Please use the tray eject tool included in the box. Otherwise, the card tray may not be ejected.
CAUTION: Never replace the included tray eject tool with sharp objects. Ensure that the tray eject tool is perpendicular to the hole. Otherwise, the phone may be damaged. -
Pull out the card tray and place the nano-SIM card on the upper card slot and the microSDXC card (optional) on the lower card slot, as shown. Carefully slide the tray back into place.
Charging the Phone
Your phone’s battery should have enough power for the phone to turn on, find a
signal, and make a few calls. You should fully charge the battery as soon as
possible.
WARNING! Use only ZTE-approved chargers and USB Type-C cable The use of
unapproved accessories could damage your phone or cause the battery to
explode.
WARNING! Do not remove the back cover. The battery is not removable.
Removal may cause fire or explosion.
-
Connect the adapter to the charging jack.
-
Connect the charger to a standard AC power outlet.
-
Disconnect the charger when the battery is fully charged.
NOTE:
If the battery is extremely low, you may be unable to power on the phone even
when it is being charged. In this case, try again after charging the phone for
at least 20 minutes. Contact customer service if you still cannot power on the
phone after prolonged charging.
Powering On/Off Your Phone
Make sure the battery is charged before powering on.
- Press and hold the Power key to turn on your phone.
- To power off, press and hold the Power key to open the options menu, and touch
.
NOTE:
If the screen freezes or takes too long to respond, try pressing and holding
the Power key for over 10 seconds to restart the phone.
Product Safety Information
| Don’t make or receive phone calls while driving. Never text while
driving.
---|---
| Keep your phone at least 10 mm away from your body while making calls.
| Small parts may cause choking.
| Your phone can produce a loud sound.
| To prevent possible hearing damage, do not listen at high volume levels
for long periods. Exercise caution when holding your phone near your ear while
the loudspeaker is in use.
| Avoid contact with anything magnetic.
| Keep away from pacemakers and other electronic medical devices.
| Turn off when asked to in hospitals and medical facilities.
| Turn off when told to on aircraft and at airports.
| Turn off when near explosive materials or liquids.
| Don’t use at gas stations.
| Your phone may produce a bright or flashing light.
| Don’t dispose of your phone in fire.
| Avoid extreme temperatures.
---|---
| Avoid contact with liquids. Keep your phone dry.
| Do not attempt to disassemble your phone.
| Only use approved accessories.
| For pluggable equipment, the socket outlet shall be installed near the
equipment and shall be easily accessible.
| Don’t rely on your phone as a primary device for emergency
communications.
FCC RF Exposure Information (SAR)
This phone is designed and manufactured not to exceed the emission limits for
exposure to radio frequency (RF) energy set by the Federal Communications
Commission of the united states.
During SAR testing, this device was set to transmit at its highest certified
power level in all tested frequency bands and placed in positions that
simulate RF exposure in usage against the head with no separation, and near
the body with the separation of 10 mm. Although the SAR is determined at the
highest certified power level, the actual SAR level of the device while
operating can be well below the maximum value. This is because the phone is
designed to operate at multiple power levels so as to use only the power
required to reach the network. In general, the closer you are to a wireless
base station antenna, the lower the power output.
The exposure standard for wireless devices employing a unit of measurement is
known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is
1.6 W/kg.
This device is complied with SAR for general population/uncontrolled exposure
limits in ANSI/IEEE C95.1-1992 and had been tested in accordance with the
measurement methods and procedures specified in IEEE1528.
The FCC has granted an Equipment Authorization for this model phone with all
reported SAR levels evaluated as in compliance with the FCC RF exposure
guidelines. SAR information on this model phone is on file with the FCC and
can be found under the Display Grant section of
www.fcc.gov/oet/ea/fccid after searching on FCC
ID: SRQ-ZTE9047. The FCC ID also can be found on the device when you open
Settings > About phone > FCC ID.
For this device, the highest reported SAR value for usage against the head is
1.26 W/kg, and for usage near the body is 1.09 W/kg.
While there may be differences between the SAR of various phones and at
various positions, they all the government requirements.SAR compliance for
body-worn operation is based on a separation distance of 10 mm between the
unit and the human body. Carry this device at least 10 mm away from your body
to ensure the RF exposure level is compliant or lower to the reported level.
To support body-worn operation, choose the belt clips or holsters, which do
not contain metallic components, to maintain a separation of 10 mm between
this device and your body.
RF exposure compliance with any body-worn accessory, which contains metal, was
not tested and certified, and using such body-worn accessories should be
avoided.
FCC Regulations
This device complies with part 15 of the FCCRules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Changes or modifications not expressly approved by the manufacturer could void
the user’s authority to operate the equipment. The antenna(s) used for this
transmitter must
not be co-located or operating in conjunction with any other antenna or
transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>