Rits Electronics M564DV Charging Stand User Manual

Rits Electronics M564DV Charging Stand

OVERVIEW

1. Charging Coil Core LED
2. LED Indicator
3. Release Button
4. Smart Touch Sensor
5. Charging Coil Slider (Refer to G))
6. Vent Clip Mount
7. Dash Mount
8. QC 3.0 Car Charger
9. USB Type C Cable

PRODUCT ASSEMBLY

1. MOUNTING BASE & HOLDER
2. TIGHTEN THE CAP TO SECURE
3. CRADLE FEET

WIRELESS CHARGING[

](https://manuals.plus/wp- content/uploads/2022/07/Rits-Electronics-M564DV-Charging-Stand-fig-8.png)

CONNECTING TO CHARGER
The USB charger to be connected to this product requires a capacity of 5V / 2.0A or higher. Use the provided Qualcomm QC3.0 car charger with 9V output and USB type C cable for fast wireless charging. Wireless charging is possible when using a 5V charger. However, fast charging is not supported.

FINDING THE POSITION OF THE WIRELESS CHARGING COIL
Fast wireless charging of smartphones with less heat requires perfect alignment between the wireless charging coils of the holder and smartphone. Most smartphones have a built-in wireless charging coil in the center of the phone as shown.

AUTO GRIP SENSOR OPERATION

1. Connect a USB cable to the car charger and holder. Core LED and LED indicator light up.

2. Put the phone on cradle feet at an angle as shown in the picture. Move the charging coil slider on the back of the holder up or down to perfectly align the coils of the smartphone and wireless charging holder.
   A Phone should be placed on cradle feet when aligning charging coils.

3. Whilst holding the phone, lightly touch the touch sensor panel with phone

   • and the grips will automatically open.®
   • The touch sensor panel works only when the grips are completely closed.
   • Touch panel with finger as it may not respond with phones using thick cases.
   • Alternatively, press the release button to open grips without touching the touch sensor panel.
   • The grips close automatically when wireless charging begins after mounting the smartphone.
   • If wireless charging does not begin, the grips will remain open. Please check the alignment of the charging coils again.
   • Keep fingers away from grips when they are retracting.
   • The touch sensor panel is marked with a sticker on the front. No other part of the holder will respond to the sensor.

AUTO GRIP[

](https://manuals.plus/wp- content/uploads/2022/07/Rits-Electronics-M564DV-Charging-Stand-fig-9.png)

PHONE REMOVAL

1. Hold the phone and press the release button to open the grips.
2. When the phone is removed, wireless charging ceases and grips will automatically close after 2 seconds.
   • A Wait 2 seconds for the grip to close automatically to proceed.
   • If the phone is removed while wireless charging is not performing normally,
3. If the USB cable is not connected to the holder or the car is turned off, gently twist the phone away from the holder to remove it.

TURN WIRELESS CHARGING ON/ OFF

Frequent charging or continued charging when fully charged may reduce the life of the phone battery, The product can work as a holder without charging or mount a phone that does not support wireless charging, In cases above, follow below steps:

1. Press and hold the release button 5 for about 3 seconds. The wireless charging coil LED switches off and the wireless charging function is disabled.
2. If the grips are open, they will close automatically.
3. Enable wireless charging by pressing the release button 5 for 3 seconds.

If wireless charging is disabled, the auto sensor function works normally. However, the grips will not close automatically. Press the release button to close grips 3

VENT CLIP INSTALLATION

1. Unfasten the clip sufficiently by rotating the clip lever.
2. Insert clip to the center of the 3 vents as shown.
   • If this way of fixing the clip is not possible, attach the fixing plate to the vent frame and insert the clip into a suitable vent.
3. Fasten lever whilst pushing clip deeper so there is no gap between clip support and vent.
4. Check if the vent clip is fixed firmly and correctly

If the temperature of the holder exceeds 28″C, the overheating protection circuit may activate and slow down or stop wireless charging. Please turn off the air vent flow where the mount is being installed

DASH INSTALLATION

Before installation, test the position of the mount in a few different areas on your dash. Choose a location that is easiest for you to access by hand.
For best results, please make sure the adhesive makes full contact with the surface you are installing on. This will ensure strong adhesion of the mount base.

1. Clean the chosen area with a cloth making sure to remove any dust or oils.  The surface must not be slippery.
2. Remove the adhesive backing from the mount.
3. Position the mount on the chosen area; press and hold firmly into place for about 30 seconds.
4. Gently tug on the mount to test if it stays in place.
5. Wait 24 hours after installation for the adhesive to cure.

Please note that the 3M adhesive is not reusable

CAUTIONS

1. Check the LED indicator periodically to ensure wireless charging is working safely. The indicator lights up as follows according to the charging status Charging Errors/ Protections Overvoltage & overcurrent, low voltage & low current, Overheating, Misalignment Foreign Object Detection

2. If the phone case thickness exceeds 2.5mm, wireless charging may be slow or stop completely.

3. If the temperature of the holder exceeds 28°C, the overheating of the protection circuit may activate and slow down or stop wireless charging.

4. If using an app requiring the use of GPS signals, such as navigation whilst charging wirelessly, your app may stop working instantly in areas where
   the GPS signal is weak. In this case, press and hold the release button 5 for more than 3 seconds to temporarily turn off the wireless charging function.

5. Depending on the model of the smartphone, the wireless coil may be built in a lower position rather than the center of the phone. In this case, fold the foot stand and align it to the center of the wireless coil.

6. Periodically check the tightness of the vent clip base to prevent unexpected dropping of the phone.

7. Do not install the holder where it will obstruct the driving view.

8. Do not operate the phone and holder while driving

FCC Statment

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement

This- equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. FCC ID: 2A7HQ-M564DV

Documents / Resources

| Rits Electronics M564DV Charging Stand [pdf] User Manual
M564DV, 2A7HQ-M564DV, 2A7HQM564DV, M564DV Charging Stand, Charging Stand
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>