neovo DR-17G Dental LCD Monitor User Guide
- June 5, 2024
- neovo
Table of Contents
Quick Start Guide
DR-17G & DR-22G LCD Monitor
Package Contents
Display ×l
VGA Cable ×l
Power Cord ×l
Audio Cable ×l
Power Adaptor ×l
Quick Start Guide ×l
Warranty Card ×l
A Control Panel
B Import/Output Terminals
C Removing the Stand
Thank you for choosing AG Neovo LCD Monitor. Please read this document before installing and operating the monitor for the first time. Please visit the AG Neovo website: www.agneovo.com to download the user manual for operation & installation details.
Safety Information
Make sure to check that the local power supply complies with the monitor’s power requirement indicated on the label. Mounting on any other horizontal surface overhead with a wall mount is not advisable. Disconnect this equipment from any AC (or DC) outlet before cleaning.
A. Control Panel
-
[ ] AUTO: Hot Key: Auto Adjustment/Rotate
• For the VGA input signal source, press to perform the auto adjustment.
• Press for 3 seconds to enable the Rotate function.
• When the OSD menu is ON, press to close the OSD menu or exit a submenu. -
[ ] LEFT: Hot Key: Audio Volume Adjustment
• Press to monitor the volume bar. Then press the LEFT key to decrease the volume.
• When the OSD menu is ON, press to select an option or adjust the settings. -
[ ] RIGHT: Hot Key: Screen Freeze
• Press to activate the screen freeze function. To deactivate, press any key except for the Power key.
• When the volume bar appears, press to increase the volume.
• When the OSD menu is ON, press to select an option, adjust the settings, or enter the submenu. -
[ ] UP: Hot Key: PIP/PBP Select
• Press repeatedly to select PIP/PBP option (PIP → PBP → OFF).
• When the OSD menu is ON, press to select an option or adjust the settings. -
[ ] DOWN: Hot Key: PICTURE MODE Select
• Press repeatedly to select the PICTURE MODE option (Standard → CCTV → VIDEO).
• When the OSD menu is ON, press to select an option or adjust the settings.
• When PIP is ON, press to swap the PIP main and sub picture. -
[ ] MENU:
• Press to monitor/hide the OSD menu. -
[ ] SOURCE:
• Press to select the input signal source. -
[ ] POWER and LED Indicator:
• Press to turn the power on or off.
• Indicate the operating status of the LCD monitor:
– Lights Green when the LCD monitor is turned on.
– Lights Amber when the LCD monitor is in standby mode.
– Lights Off when the LCD monitor is turned off.
B. Input/Output Terminals
- DC IN: Connect with the supplied power adaptor.
- DVI: Connect DVI signals input.
- HDMI: Connect HDMI signals input.
- DisplayPort: Connect DisplayPort signals input.
- VGA: Connect VGA signals input.
- AUDIO IN: Connect audio signals input (3.5 mm Stereo Audio Jack).
- S-VIDEO: Connect S-Video signals input.
- COMPOSITE-1/COMPOSITE-2 IN: Connect Composite signals input.
C. Removing the Stand
1. Lay the LCD monitor faces down on a flat even surface.
2. Remove the screws securing the base stand from the LCD monitor.
3. Detach the base stand.
M4 x 10mm screw
Trouble Shooting
If there is no response from the monitor
• The LED indicator is OFF.
– Check if the LCD monitor is turned ON.
– Check if the power cord is properly connected to the LCD monitor.
– Check if the power cord is plugged into the power outlet.
- COMPOSITE-1/COMPOSITE-2 OUT: Connect Composite signals output.
- AUDIO IN: Connect audio signals input (RCA Stereo Audio Jack).
- AUDIO OUT: Connect audio signals output (RCA Stereo Audio Jack).
- USB (SERVICE): Connect USB 2.0 for service.
- RS232: Connect RS232 input from external equipment.
- GROUNDING STUD: Connect to proper earth ground.
• LED indicator is AMBER
– Check if the computer is turned ON.
– Check if the computer is in standby mode.
www.agneovo.com
DR-17G/DR-22G Eprel registration number: 1187882/1187878
Copyright © 2022 AG Neovo. All rights reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>