Einhell BT-AG 850 Angle grinder Instructions

BT-AG 850 Angle grinder

**BT- AG 850
Original operating instructions
Angle grinder

Art.-Nr.: 44.305.90
I.-Nr.: 11074

**

“Caution – Read the operating instructions to reduce the risk of inquiry”
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Wear a breathing mask.
Dust that is injurious to health can be generated when working on wood and other materials.
Never use the device to work on any materials containing asbestos!

Wear safety goggles.
Sparks generated during working or splinters, chips, and dust emitted by the device can cause loss of sight.

This safety guard is designed for sanding/grinding.

This safety guard is designed for cutting and grinding/sanding. (not included in items supplied)

Important!
When using equipment, a few safety precautions must be observed to avoid injuries and damage.
Please read the complete operating manual with due care. Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, give them these operating instructions as well.
We accept no liability for damage or accidents which arise due to the non- observance of these instructions and the safety information.

Safety information

Please refer to the booklet included in the delivery for the safety instructions.
CAUTION!
Read all safety regulations and instructions.
Any errors made in following the safety regulations and instructions may result in an electric shock, fire, and/or serious injury.
Keep all safety regulations and instructions in a safe place for future use.

Layout (Fig. 1)\

1. Spindle lock
2. ON/OFF switch
3. Additional handle
4. Guard
5. Flange nut wrench

Items supplied

• Open the packaging and take out the equipment with care.

• Remove the packaging material and any packaging and/or transportation braces (if available).

• Check to see if all items are supplied.

• Inspect the equipment and accessories for transport damage.

• If possible, please keep the packaging until the end of the guarantee period.
  IMPORTANT
  The equipment and packaging material are not toys. Do not let children play with plastic bags, foils or small parts. There is a danger of swallowing or suffocating!

•  Original operating instructions

•  Safety instructions

Proper use

The angle grinder is designed for grinding metal and stone when using the appropriate grinding wheel and guard.
Caution! To cut metal and stone the grinder/sander may only be used when the guard (available as an accessory) is mounted.
The machine is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user/operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this.
Please note that our equipment has not been designed for use in commercial, trade, or industrial applications. Our warranty will be voided if the machine is used in commercial, trade, or industrial businesses or for equivalent purposes.

Technical data

Sound and vibration

Sound and vibration values were measured in accordance with EN 60745.

Wear ear-muffs.
The impact of noise can cause damage to hearing.

Total vibration values (vector sum of three directions) determined in accordance with EN 60745.

Surface sanding/grinding
Vibration emission value ah = 4.9 m/s 2
K uncertainty = 1.5 m/s 2
Additional information for electric power tools
Warning!
The specified vibration value was established in accordance with a standardized testing method. It may change according to how the electric equipment is used and may exceed the specified value in exceptional circumstances.
The specified vibration value can be used to compare the equipment with other electric power tools.
The specified vibration value can be used for the initial assessment of a harmful effect.

Keep the noise emissions and vibrations to a minimum.

• Only use appliances that are in perfect working order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Has the appliance been serviced whenever necessary?
• Switch the appliance off when it is not in use.
• Wear protective gloves.

Residual risks
Even if you use this electric power tool in accordance with instructions, certain residual risks cannot be ruled out. The following hazard may arise in connection with the  equipment’s construction and layout:

1. Lung damage if no suitable protective dust mask is used.
2. Damage to hearing if no suitable ear protection is used.
3. Health damage is caused by hand-arm vibrations if the equipment is used over a prolonged period or is not properly guided and maintained.

Before starting the equipment

Before you connect the equipment to the mains supply make sure that the data on the rating plate is identical to the mains data.

6.1 Fitting the additional handle (Fig. 2)

• The angle grinder must not be used without the additional handle (3).
• The additional handle can be secured in any of 2 positions (A, B).

6.2 Setting the guard (Fig. 3)

• Switch off the tool. Pull the power plug.
• Adjust the guard (4) to protect your hands so that the material being ground is directed away from your body.
• The position of the guard (4) can be adjusted to any specific working conditions. Undo the screw  (a) and turn the cover (4) into the required position.
• Ensure that the guard (4) correctly covers the gear wheel casing.
• Retighten the screw (a).
• Ensure that the guard (4) is secure.

Take care that the safety device is secure.
Never use the angle grinder without the guard.

6.3 TEST RUN FOR NEW GRINDING WHEELS
Allow the right-angle grinder to run in idle for at least 1 minute with the grinding or cutting wheel fitted in place. Vibrating wheels are to be replaced immediately.

Operation

7.1 Switch (Fig. 4)
The angle grinder comes with a safety switch that is designed to prevent accidents. To switch on, push the slide switch (a) to the right while at the same time pushing the ON/OFF switch (2) forwards and depressing. To switch off the angle grinder, depress the button (2) at the back. The switch (2) will jump back into its starting position.

****Wait until the machine has reached its top speed. You can then position the angle grinder on the workpiece and machine it.

7.2 Changing the grinding wheels (Fig. 5)
Use the face spanner (5) supplied to change the grinding wheels.

Pull out the power plug.

• Simple wheel change by spindle lock:

• Press the spindle lock and allow the grinding wheel to latch in place.

• Open the flange nut with the face spanner.
  (Fig. 5)

• Change the grinding or cutting wheel and tighten the flange nut with the face spanner.
  ****Important!
  Only ever press the spindle lock when the motor and grinding spindle are at a standstill! You must keep the spindle lock pressed while you change the wheel! For grinding or cutting wheels up to approx. 3 mm thick, screw on the flange nut with the flat side facing the grinding or cutting wheel.

7.3 Flange arrangements when using grinding wheels and cutting wheels (Fig. 6-9)

• Flange arrangement when using a depressedcentre or straight grinding wheel (Fig. 7)
  a) Clamping flange
  b) Flange nut

• Flange arrangement when using a depressedcentre cutting wheel (Fig. 8)
  a) Clamping flange
  b) Flange nut

• Flange arrangement when using a straight
  cutting wheel (Fig. 9)
  a) Clamping flange
  b) Flange nut

7.4 MOTOR
It is vital for the motor to be well ventilated during operation. Be sure, therefore, to keep the ventilation holes clean at all times.

7.5 GRINDING WHEELS

• Never use a grinding or cutting wheel bigger than the specified diameter.
• Before using a grinding or cutting wheel, check its rated speed.
• The wheel s rated speed must be higher than the idle speed of the right-angle grinder.
• Use only grinding and cutting wheels that are approved for a minimum speed of 11000 rpm and a peripheral speed of 80 m/sec.
• Check the direction of rotation when you use diamond cutting wheels. The directional arrow on the diamond cutting wheel must point in the direction in which the tool rotates.

Take special care that the grinding/sanding wheels are properly stored and transported. Ensure that the grinding/sanding wheels are never exposed to shock, jolts, or sharp edges (for example during transport or storage in a toolbox). This could cause damage (such as cracks) to the grinding/sanding wheels and place the user in serious danger.

7.6 OPERATING MODES
7.6.1 Rough grinding
**Caution: Use the safety device for sanding/grinding (included in items supplied).
For the best rough grinding results, hold the grinding wheel at an angle of between 30° and 40° to the workpiece surface and guide it back and forth over the workpiece in steady movements.
7.6.2 Cutting
Caution: Use the safety device for abrasive cutting (available as an accessory, see 9.4)
When you use the right-angle grinder for cutting purposes, avoid tilting it in the cutting plane. The cutting wheel must have a clean cutting edge.
A diamond cutting wheel is best used to cut hard stone.
**It is prohibited to use the machine on asbestos materials!
****Never use a cutting wheel for rough grinding.

Replacing the power cable

If the power cable for this equipment is damaged, it must be replaced by the manufacturer or its aftersales service or similarly trained personnel to avoid danger.

Cleaning, maintenance, and ordering of spare parts

Always pull out the mains power plug before starting any cleaning work.
9.1 Cleaning

• Keep all safety devices, air vents, and the motor housing free of dirt and dust as far as possible.
  Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.

• We recommend that you clean the device immediately each time you have finished using it.

• Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the device.

9.2 Carbon brushes
In case of excessive sparking, have the carbon brushes checked only by a qualified electrician.
Important! The carbon brushes should not be replaced by anyone but a qualified electrician.
9.3 Maintenance
There are no parts inside the equipment which require additional maintenance.
9.4 Ordering replacement parts
Please quote the following data when ordering replacement parts:

• Type of machine
• Article number of the machine
• Identification number of the machine
• Replacement part number of the part required

For our latest prices, information and order details please go to www.isc- gmbh.info
Safety guard for cutting (Art. No.: 44.500.09)

Storage

Store the equipment and accessories out of the children’s each in a dark and dry place at above freezing temperature. The ideal storage temperature is between 5 and 30 °C. Store the electric tool in its original packaging.

Disposal and recycling

The unit is supplied in packaging to prevent it’s being damaged in transit. This packaging is raw material and can therefore be reused or can be returned to the raw material system.
The unit and its accessories are made of various types of material, such as metal and plastic.
Defective components must be disposed of as special waste. Ask your dealer or your local council.

**ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar
Konformitätserklärung

explains the following conformity according to EU directives and norms for the following product
**

Winkelschleifer BT-AG 850 (Einhell)

87/404/EC_2009/105/EC
2005/32/EC_2009/125/EC
2006/95/EC
2006/28/EC
X 2004/108/EC
2004/22/EC| 1999/5/EC
97/23/EC
90/396/EC_2009/142/EC
89/686/EC_96/58/EC
X 2011/65/EC
X 2006/42/EC
---|---

• Annex IV
  Notified Body:
  Notified Body No.:
  Reg. No.:

• 2000/14/EC_2005/88/EC
  Annex V
  Annex VI
  Noise: measured L WA= dB (A); guaranteed LWA = dB (A)
  P = KW; L/Ø = cm
  Notified Body:

• 2004/26/EC
  Emission No.:

Standard references: EN 60745-1; EN 60745-2-3; EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3

Landau/Isar, den 24.04.2014

First CE: 07
Art.-No.: 44.305.90
I.-No.: 11074
Subject to change without notice

Archive-File/Record: NAPR009620
Documents registrar: Georg Riedel Wiesenweg 22, D-94405 Landau/Isar

****For EU countries only
Never place any electric tools in your household refuse.
To comply with European Directive 2012/19/EU concerning old electric and electronic equipment and its implementation in national laws, old electric tools have to be separated from other waste and disposed of in an environment- friendly fashion, e.g. by taking to a recycling depot.
Recycling alternative to the demand to return electrical devices:
As an alternative to returning the electrical device, the owner is obliged to cooperate in ensuring that the device is properly recycled if ownership is relinquished. This can also be done by handing over the user device to a returns center, which will dispose of it in accordance with national commercial and industrial waste management legislation. This does not apply to the accessories and auxiliary equipment without any electrical components which are included with the user device.

The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products, is permitted only with the express consent of ISC GmbH.

Technical changes subject to change

Telefax: 01805 / 835 830 (Festnetz: 14 ct/min, Mobilfunk max.: 42 ct/min)
E-Mail:info@isc-gmbh.info
· Internet:www.isc-gmbh.info
iSC GmbH · Eschenstraße 6 · 94405 Landau/Isar (Deutschland)
EH 04/2014 (01)

Documents / Resources

| Einhell BT-AG 850 Angle grinder [pdf] Instructions
BT-AG 850 Angle grinder, Angle grinder
---|---

References

• iSC Onlineshop

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>