ASIGA 03624 Denta Tooth Material for Denture Teeth Instruction Manual
- June 3, 2024
- ASIGA
Table of Contents
03624 Denta Tooth Material for Denture Teeth
Instruction Manual
03624 Denta Tooth Material for Denture Teeth
Printer compatibility 385nm (UV)
Instructions For Use DentaTOOTH
DentaTOOTH A1: PN/03624, DentaTOOTH A2: PN/03625, DentaTOOTH A3: PN/03626,
DentaTOOTH B1: PN/03810, DentaTOOTH B2: PN/03812, DentaTOOTH B3: PN/03814.
Introduction:
The following instructions for use are for dental professionals who use Asiga DentaTOOTH as a material for denture teeth. This instruction for use also provides information about safety and environmental aspects. In case more information is needed, contact the reseller.
Intended Use:
Asia DentaTOOTH is intended exclusively for professional dental work.
Asia DentaTOOTH is a 3D print resin intended for the manufacturing of 3D-
printed denture teeth.
The denture teeth produced are suitable for dental indications including
removable dentures and study models.
Description, Indications & Effects:
Asia DentaTOOTH is intended to be used in combination with DLP-based 3D
printers (i.e. Asiga Max Series or Asiga Pro Series) that support Asiga
resins. The printer and resin must be optimized with respect to each other in
order to produce complete and precise printed parts. If the printer and resin
are not optimized with respect to each other this may have an adverse effect
on the accuracy and physical quality of printed parts. DLP-based 3D printers
and post-curing lightboxes make use of a light source to polymerize the Asiga
resin. Therefore, operators are advised to wear UV protective glasses when
operating a 3D printer and/or lightbox.
Differences in color nuance may occur due to : production in batches;
inadequate shaking and mixing of the original packaging before use; inadequate
stirring in the DentaTOOTH resin before use; insufficient post-curing.
Contra-Indications:
Asia DentaTOOTH should not be used for any other purpose than as a 3D print
resin for the manufacturing of denture teeth. Any deviation from this
instruction for use may have an adverse effect on the chemical and physical
quality of Asiga DentaTOOTH. In case of an allergic reaction, please contact a
medical physician.
Hazard & Precautions:
Please refer to the Asiga product safety data sheet for DentaTOOTH. For
material SDS or technical assistance, contact your Asiga resellers or open a
support ticket in your account online
https://www.asiga.com/accounts/support/
**Processing & Post-Curing:
**
Ensure the 3D printer is clean prior to use, including the imaging area and
any optical surfaces. Ensure the material tray is clear of solid debris prior
to commencing a print. The presence of solid particles in the resin may cause
deformation or failure of the printed objects. Nitrile gloves should be worn
at all times when handling Asiga liquid resins up until the finishing step.
Avoid contact with skin. If contact with skin occurs, wash thoroughly with
cold soapy water. If contact with the eyes occurs, remove any contact lenses
and flush with cold water and seek immediate medical assistance.
Mixing Before Use:
In Bottle: Agitate/shake the bottle vigorously prior to pouring for at least
one minute.
In Material Tray:
Stir the material with a soft spatula. Take care not to damage the film of
the Material Tray. This step is necessary to re-disperse the (possible)
pigment sediment from the bottom of the vessel. Color deviation and print
failures may occur if insufficiently mixed.
Fill Material Tray:
Ensure the temperature of the resin is between 15 and 30°C / 59 and 86°F and
prevent exposure to direct sunlight. Pour the resin into the material tray of
the 3D printer.
Printer Settings:
Asia DentaTOOTH is optimized to build parts using light with 385nm wavelength.
For Printer Settings, See the manual or user guides of Asiga 3D Printers
(Asiga Max Series or Asiga Pro Series). Ensure the film of the Material Tray
is clear of any debris before starting the print. Ensure you are using the
latest in the file. You can access the latest material ini file for this
material in your Asiga account online here:
https://www.asiga.com/accounts/#tab_material
Washing:
Wash parts in IPA 98%+ pure (Isopropyl alcohol) in a well-ventilated area.
Best results are achieved when using a pre and post-wash.
1. Using an ultrasonic cleaning device:
– Pre-wash bath: 2 minutes.
– Post-wash bath: 2 minutes.
Important:
Ensure a dedicated bath is used for this material. Do not wash in baths that
have previously been used for other materials. Allow parts to dry thoroughly
before post-curing. Post-Curing:
- After washing and drying, let the rest of the printed parts for at least 30 minutes to ensure the printed parts are free of alcohol residue.
- Place the printed parts in the UV curing unit “NK Optik Otoflash G171” for 2000 flashes.
- Turn parts over and allow to cool.
- Cure for a further 2000 flashes. Total: 4000 flashes (2 x 2000 flashes each side).
Post-curing is a UV-light treatment to ensure that DentaTOOTH printed parts obtain optimal polymer conversion. Through this, the residual monomer is reduced to a minimum and the required mechanical properties are obtained. We advise the use of the NK Optik Otoflash G171 post-curing box. Place parts inside the G171 Otoflash chamber on the support mesh, do not use a plastic tray inside the chamber. Inert gas is not required. Please see NK Optik Otoflash G171 user guide.
Soaking:
After post-curing, soak DentaTOOTH parts in fresh drinkable water for 60 minutes.
Storage Conditions, Expiry Date & Transport:
Store the resin in the original packaging at room temperature in a dry, cool
and dark area. Close the packaging after each use. The expiry date of the
product is mentioned on the product label along with the lot number. Store on
the printer for up to 4 weeks with the hood closed or store in a bottle for up
to 24 months in a cool dark place. The product performance is no longer
guaranteed once the expiry date is exceeded. Do not expose to UV light.
Standard transport conditions apply to this product. There are no restrictions
for transport related to hazardous substances.
Waste Disposal:
Asia resin in its polymerized form is not environmentally harmful and thus can
be disposed of in the general waste. Asia resin in its liquid state should be
treated as chemical waste. Special disposal requirements are applicable, check
with your local, federal, or other regulatory agencies for disposal
requirements.
Delivery Units:
Asia DentaTOOTH is available in 1 color only: Ivory, 1kg.
Manufactured by:
ASIA PTY LTD, UNIT 2, 19-21 BOURKE ROAD, ALEXANDRIA, NSW 2015, AUSTRALIA
AUSTRALIA HEAD OFFICE: +61 2 9690 2737
EUROPE OFFICE: +49 361 5506 6866
US TOLL FREE: +1 877-689 99 98
info@asiga.com
www.asiga.com
Instructions For Use: DentaTOOTH Revision 5
Effective Date: 28th October 2021
References
- Asiga – Precision 3D Printers & Materials
- Asiga – Precision 3D Printers & Materials
- Login - Accounts - Asiga
- Login - Accounts - Asiga
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>