thdstatic 18.90L Office Cabinets Wood Storage Dresser Cabinet Instructions

thdstatic 18.90L Office Cabinets Wood Storage Dresser Cabinet

WARNING

ADULT ASSEMBLY REQUIRED CHOKING HAZARD

• This product includes small parts, sharp points and sharp edges in its unassembled state. Keep unassembled parts away from children under 3 years of age, and animals.

SAFETY WARNINGS

• Follow the information on the warnings appearing on table and on the carton. Do not remove the warning label from the cabinet.
• Do not allow children under 3 years of age to use the cabinet.
• Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.

FURNITURE TIP-OVER HAZARD
Children have died from furniture tip-over To reduce the risk of furniture tip-over:

• ALWAYS install tip-over restraint especially if used by a wall or in the open.
• NEVER put a TV on this product
• NEVER allow children to stand, climb or hang on drawers, doors, or shelves.
• NEVER open more than one drawer at a time.
• ALWAYS place the heaviest items in the lowest cabinet.

PARENTAL SUPERVISION IS REQUIRED

• Parents or Guardians should supervise use under the intended age specifically regarding children that may have access to it and climb on the unit.
• Do not allow horseplay on, under, or behind the unit and prohibit jumping on the cabinet.
• If used improperly, your table may be pulled over or fall, creating risk of injury or damage. Children should not be permitted to climb or pull on the cabinet.

USE, MAINTENANCE & ASSEMBLY 

• Periodically check and ensure that the components are in their proper position, free from damage, and that all connectors are tight.
• Use on level surfaces only. Assemble on a soft level surface to avoid damage to unit or floor. Do not use this item if any components are missing or damaged.
• Do not use substitute parts. Contact the manufacturer or dealer for replacement parts. Only clean using a damp cloth and mild detergent, do not use bleach or abrasive cleaners. Check you have all components and tools listed on page 4
• Do not stand or put weight on this product during assembly, this could cause damage. Remove all hardware from the plastic bags and separate them into groups.
• Assemble the item as close to its final position (in the same room) as possible.
• Certain assembly steps may be easier with 2 people.
• Dispose of all packaging carefully and responsibly.
• We do not recommend power screwdrivers. Only use hand screwdrivers to prevent damage to unit.
• Keep these instructions for future reference.

COMPONENT PARTS

Please take a moment to read through the whole instruction booklet before assembly to familiarize yourself with this product. Once you feel ready to start, follow the instructions step by step and this should make this process as easy as we could make it for you.

Please check that you have all the parts listed below

1. Top Panel ×1
2. Left Side Panel×1
3. Right Side Panel×1
4. Bottom Panel×1
5. First Back Side Panel ×1
6. Second Back Side Panel ×1
7. Third Back Side Panel×1
8. Fourth Back Side Panel ×1
9. Fifth Back Side Panel ×1
10. Drawer Back ×9
11. Drawer Left ×9
12. Drawer Right ×9
13. Drawer Bottom ×9
14. Drawer Front ×5
15. Drawer Front ×4
16. Support Side Panel ×1

ASSEMBLY HARDWARE

Tools Required

• Phillips Screwdriver
  (Medium) (not included) *Do Not Use Power Screwdriver or Drill..

• Hex Screwdriver (included)

ASSEMBLY INSTRUCTIONS

1. Select A×54 and 2×1, 3×1. Position 2 in the left, position 3 in the right. Insert A×9 into one side of the B CL, the other A×9 into the middle of the B CL, other A×9 into the other side of the B CL.Insert B CL×9 into the 2.Repeat the steps for B CR and 3. 
2. Select 10×9,11×9,12×9, and G×36. Insert G×2 into the hole of the 11 into the 10.Re-peat the steps for 10 and 12. Repeat the steps for another Drawer panels×8.
3. Select 13×9,14×5, D×10, E×10, F×10. Install the 13 along the grooves on the both sides of the 11 and 12. Install the 14 on the 11 with the D, E and F. Repeat the steps for the 14 and the 12. Repeat for another Draw-er×4.
4. Select A × 30, B DR×5, B DL × 5. Put the Drawer upside down. Insert A×3 into the B DR into the 12 tightly. Repeat the steps for B DL and the 11.Repeat the steps for another Drawer ×4.
5. Select 15×4,D×8,E×8,F×8. Install the 15 on the 11 with the D, E and F. Repeat the steps for the 15 and the 12. Repeat for another Draw-er×3. 
6. Select A × 24, C DR×4, C DL ×4. Put the Drawer upside down. Insert A×3 into the C DR into the 12 tightly. Repeat the steps for C DL and the 11.Repeat the steps for another Drawer ×3.
7. Select 3,6,8,16, D×3,E×3,F×3. Insert the 6 into the 3 with the D,E,F tightly.Repeat for the 8 and the 16. 
8. Select2,3,6,7,8,16,D×3,E×3,F×3. Install the 7 along the grooves of the 6 and the 8. Insert the 2 into the 6 and the 8 with the D×2, E×2, F×2. Repeat for the 2 and the 16.
9. Select 9,4, E×4,G×4. Install the 9 along the groove of the 8. Insert one side of the 4 into the 2 with E×2,G×2. Repeat for the other side of the 4 and the 3. 
10. Select 1,5,D×4,E×4,F×4. Install the 5 along the groove of the 6.Insert one side of the 1 into the 2 with the D×2,E×2,F×2. Repeat for the 1 and the 3.
11. Put the Drawers ×9 into the Cabinet. 
12. Select C ×12, J×12.Install the C ×12 into the two sides of the back of the Cabi-net with the J ×12.
13. Select I × 2, A×4. Install the I ×2 into the two sides of the back of the Cabi-net with the A ×4.
14. Select H × 2, G×2. Install the H ×2 into the wall with the G ×2.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>