Bintronic BT-073 Smart Vertical Blinds Instruction Manual
- June 3, 2024
- Bintronic
Table of Contents
- Bintronic BT-073 Smart Vertical Blinds
- Instruction Manual
- Travel Distance Setting and Revising
- Adding another Remote Control Unit
- Clear off Password
- Externally connected Manual Switch Box
- Battery Replacement
- Product Specifications
- Quick Setting Index
- Instructions for using the Remote Control Holder
- Documents / Resources
Bintronic BT-073 Smart Vertical Blinds
Instruction Manual
How to open the Battery Compartment Cover
Push the cover out
- STOP (1) When the curtain is moving, press [STOP] to stop the curtain.
- When the curtain is not moving, press [STOP] to flip the slats to the center position.
How to replace Battery Compartment Cover
- Insert latches into corresponding slots
- Place the Battery Compartment Cover to engage it with Slides
- Push the cover in Insert latches
Key check-points prior to making settings
- Make sure the slats of the Vertical Blinds are installed properly before setting.
- If six beep sounds occur during the setting, it means that the setting is not completed yet; it might be because there is a power failure during the setting or [STOP] is accidentally pressed. Please go back to steps 1-1 to reset.
Travel Distance Setting and Revising
- Press the [OPEN] + [SET] keys until a short beep sound occurs.
- A long beep sound will occur, indicating that the travel distance setting is completed.
- Please repeat steps 1-1 if there is something wrong with the travel distance of the curtain.
Adding another Remote Control Unit
- Press and hold [SET] until three short beep sounds occur, indicating that the setting mode of Adding another Remote Control Unit is activated.
- Now press the [STOP] key of the Remote Control to be added; the adding process is completed when a short beep sound occurs.
Setting Completed
After the setting is completed, a long beep sound will occur, indicating that the setting mode is deactivated.
Clear off Password
Unplug the power supply of the Motor, wait for 15 seconds, and resume the power supply of it. Within 8 seconds, press [OPEN] + [STOP] + [CLOSE] + any of blank keys [LEFTWARD LIGHT FILTERING] OR [RIGHTWARD LIGHT FILTERING] altogether 4 keys, beep sounds will occur immediately, then, within 5 seconds, press and hold [OPEN] + [CLOSE]. The beep sounds will then stop, indicating that the password is cleared off.
When everything is done, only the password of this remote remains, others will be erased. If a new password is not added, the old password will not be erased.
Externally connected Manual Switch Box
Instructions
A brief contact will activate the function; DO NOT short-circuit continuously.
- Green + Brown = open the curtain
- Green + Yellow = close the curtain
- Green + Red = if the curtain is moving, it will stop immediately.
- = if the curtain is not moving, the slats will be turned.
- REMINDER The slats cannot be turned if the current position of the curtain is at 1/4 of the total travel distance. Green + Brown + Red = the curtain turns left; the slats open.
- Green + Yellow + Red = the curtain turns right; the slats close.
Battery Replacement
- With a flat side (positive +) of the Battery facing upwards, making sure that the Battery is latched up by two spring plates, insert the Battery at a slanted angle to enter it into the Battery Holder.
- Completed.
Product Specifications
- Battery: CR2450 3V (One-time type lithium battery)
- Dimensions: L 13CM, W 4.8CM, H 1.1CM
- Standby Current: <1uA
- Modulation Method: OOK
- Encoding Method: Internally-burnt fixed coding
- Transmission Frequency: 433.92MHz
- Antenna Type: on board, Gain=0 dbi
- Weight (including battery): 66g
Quick Setting Index
Travel Distance Setting and Revising:
- Press the [SET] + [OPEN] keys and the curtain begins to set the travel distance automatically.
- A long beep sound will occur, indicating that the travel distance setting is completed.
Adding another Remote Control Unit:
- Press [SET], and three short beep sounds will occur.
- Then press (Remote Control 2) [Stop], and one short beep sound occurs, indicating that the setting is completed.
Clear Off Password:
- Press [OPEN] + [STOP] + [CLOSE] + [LEFT LIGHT FILTERINF] or [RIGHT LIGHT FILTERING] altogether 4 keys. Beep sounds will occur immediately.
- Then, within 5 seconds, press [OPEN] + [CLOSE], and the beep sounds will stop, indicating that the setting is completed.
Instructions for using the Remote Control Holder
Open-up support plate on the back for use as a vertical holder.
Wall-mount Holder
Apply the provided double-face adhesive tape on the back of the Holder and stick it onto the desired position on the wall, as a wall-mounted holder.
Apply the adhesive tape
- BINTRONIC ENTERPRISE CO., LTD
- No.62, Bengong 5th Rd., Gangshan Dist., Kaohsiung City 82059, Taiwan (R.O.C.)
- Email:sales@bintronic.com
- This instruction manual version is v1.0.
Documents / Resources
|
Bintronic BT-073 Smart Vertical
Blinds
[pdf] Instruction Manual
BT-073 Smart Vertical Blinds, BT-073, Smart Vertical Blinds, Vertical Blinds,
Blinds
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>