Bintronic BT-073 100-Level Smart Roller Shades Instruction Manual

: June 4, 2024
: Bintronic

Bintronic BT 073 100 Level Smart Roller Shades

Parts overview

How to open Battery Compartment Cover

How to replace Battery Compartment Cover

Bintronic BT-073 100-Level Smart Roller Shades 3

Insert latches into corresponding slots.
Place Battery Compartment Cover to engage it with Slides.
Push the cover in.

Key check points prior to making settings

When setting Upper-/Lower-Limit points, set Upper Limit first, then the Lower Limit.
First, make sure if the direction of movement is correct.
Verify if the Roller Shade moves upwards by pressing UP and downwards by pressing DOWN. After that, carry out setting or modification of Upper/Lower.
Limit points. In case the Roller Shade moves in the opposite direction, refer to the Steps of Item 3-1 in Table of Contents to correct the direction.

Setting or modify position of Upper Limit

STEP 1

Press [SET] + [Open] keys until the Motor makes a twitch, indicating the setting mode of Upper-Limit is activated. the Motor will make a twitch. When the Motor makes a twitch, the Roller Shade will move upwards and downwards at the same time as a response.

STEP 2

Press [Open] or [Close] key to move the Roller Shade to a pre-determined position, to be set as the Upper-Limit.

CAUTION
While the Shade is getting close to reaching the Upper-Limit, please press [Stop] to stop the movement to avoid damage to the motor. Then, tap to fine tune to the place where you would like to be set up as the Upper-Limit. Press [Stop] and tap to fine tune to the Upper-Limit.

Step 3

When the pre-determined position is reached, press [Stop] key once to stop the movement; press any of the blank keys [Left] and [Right] + [Set] to confirm; the setting is completed when Motor makes a twitch press any
press [Stop] of the blank keys The motor makes a twitch. When the Motor makes a twitch, the Roller Shade will move upwards and downwards at the same time as a response. Setting Completed When all procedures are done, the Lower-Limit setting is completed, too.

Setting or modifying position of Lower Limit

Press (SET]+ [Close] keys until Motor makes a twitch.

STEP 1

Indicating that the setting mode of Lower-Limit is activated the Motor will make a twitch When the Motor makes a twitch, the Roller Shade will move upwards and downwards at the same time as a response.

STEP 2

Press [Open] or [Close] key to move the Roller Shade to a pre-determined position, to be set as the Lower Limit. Tap to fine tune. Press for 2 seconds, and it will move continuously.

CAUTION
When entering the Lower-Limit position setting mode, the mode will be deactivated if no keys are pressed within 5 seconds. Plus. previous setting will not be recorded. Please go back to STEP-1 and reset it.

Step 3

When the pre-determined position is reached, press the [Stop] key once to stop the movement STEP-3 press any of the blank keys [Left| and [Right| + [Set to confirm: the setting is completed when the Motor makes a twitch. Setting Completed When the Motor makes a twitch, the Roller Shade will move upwards and downwards at the same time as a response. When all procedures are done, the Lower-Limit setting is completed.

Adding another Remote Control Unit

Press and hold [SET] +[Stop] until the Motor makes a twitch, STEP-1 indicating that the setting mode of Adding another Remote Control Unit is activated

Now press [Stop] key of the Remote Control to be added; STEP-2 the adding process is completed when the Motor makes a twitch. When the Motor makes a twitch, the Roller Shade will move upwards and downwards at the same time as a response.

Setting Completed

When all procedures are done, please do not press any key and wait for 5 seconds until the Motor makes a twitch, indicating that the setting is completed.

Alter direction of Smart Roller Shade

Step 1

Press [SET]+ [Stop] keys until the Motor makes a twitch, STEP-1 indicating the activation of the setting mode. the Motor will make a twitch L back When the Motor makes a twitch, the Roller Shade will move upwards and downwards at the same time as a response.

Step 2

Now press [Open]+ [Stop]+ [Close] keys all together, Motor rotates in reverse direction press [Open]+ [Stop]+ [Close] keys all together again, Motor rotates in forward direction. the Motor rotates in forward direction for the 2nd time STEP-2 Setting Completed When all procedures are done please do not press any key and wait for 5 seconds until the Motor makes a twitch, indicating that the setting is completed. the Motor rotates in reverse direction for the 1st time.

Clear off Password

Step 1

Bintronic BT-073 100-Level Smart Roller Shades 8

Unplug power supply of the Motor, wait for 15 seconds, resume power supply of it. Press [Open]+ [Stop]+ [Close]+ any of blank keys [Left] and [Right. altogether 4 keys, within 8 seconds until Motor makes a twitch. unplug power supply- wait for 15 seconds- resume power supply- press 4 keys altogether the Motor makes a twitch. After Motor makes a twitch, simultaneously press [Open]+ [Close] keys of the Remote Control within 8 seconds. Password is cleared off when the Motor makes a twitch the Motor will make a twitch.

Setting Completed

When all the procedures are done, only the password of this remote remains, others will be erased. If a new password is not added, the old password will not be When the Motor makes a twitch, the Roller Shade will move upwards and downwards at the same erased. time as a response.

Externally connected Manual Switch Box

Bintronic BT-073 100-Level Smart Roller Shades 9 A brief contact will activate the function; DO NOT short-circuit continuously.

Battery Replacement

With flat side positive + of the Battery facing upwards, making sure that the Battery is latched up by two spring plates, insert Battery in a slanted angle to enter it into the Battery Holder. Completed.

Product Specifications

Battery: CR2450 3V One-time type lithium battery
Dimensions: L 13CM, W4.8CM, H 1.1CM
Standby Current: <1ua
Modulation Method: OOK
Encoding Method: Internally-burnt fixed coding
Transmission Frequency: 433.92MHz
Antenna Type: on board, Gain=0 dbi
Weight (including battery) 66g

Quick Setting Index

Upper Limit Setting: [SET]+ [Left] or [Right] blank blank key key
Lower-Limit Setting: [SETJ+ [Left] or [Right] blank key
Set Favorite Position: [SET]+ [Close] twice
Add another Remote Control: [SET]+ [Stop],
Remote Control 2) [Stop]
Alter direction of Roller Shade movement: [SET]+[Stop]
[Open]+ [Stop]+ [Close] (reverse direction
[Open]+[Stop]+ [Close] (forward direction
Clear off Password: [Open]+[Stop]+ [Close]+ any of [Left] and [Right] blank key Open+ Close