DS18 CF-X10TP.NS Marine Tower Pod For 10 Inch Speakers Owner’s Manual

: June 5, 2024
: DS18

Table of Contents

FEATURES
PACKAGING INCLUDES
READ BEFORE INSTALLATION
INSTALLATION EQUIPMENT
SPECIFICATIONS
MEASUREMENT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

OWNER’S MANUAL
CF-X10TP.NS
MARINE TOWER POD FOR 10″ SPEAKERS
WITH GRILL, RGB LED LIGHTS AND
CARBON FIBER TEXTURE

FEATURES

Pair of empty enclosures to use with your favorite DS18 10” Speakers
IP65 Marine Grade Compliant Specifications, 100% UV Stable
Grill with Injection Molded Composite with 316 Stainless Steel mesh
Integrated RGB LED Lighting
LED Controller with Smartphone App (LED BTC) Available For Multi-Function RGB LED Lighting option (Sold Separately)

PACKAGING INCLUDES

(2) CF-X10TP.NS Marine Towers
(2) Mounting clamps (Pre-Installed on speakers)
(4) M6 x 15mm bolts (Pre-Installed)
(6) Rubber clamp adapters (1/8” thickness)

READ BEFORE INSTALLATION

Be sure to carefully read and understand the instructions before attempting to install these speakers.
For safety, disconnect the negative battery terminal from the battery prior to beginning the installation.
For easier assembly, we suggest you have all your tools in hand- Drill, Allen set, Crimp, Soldering iron, Wire Strippers, Heat-shrink, etc.
Use high-quality “Waterproof’ connectors for a reliable installation and to minimize signal or power loss.
Think before you drill! Be careful not to cut or drill into the gas tanks, fuel lines, brake or hydraulic lines, vacuum lines, or electrical wiring when working on any vehicle. If installing in a boat, make sure not to cut or drill through the main hull.
Never run wires near fuel lines or power (if possible). Running the wires inside the hull or car area provides the best protection.
Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the tower.
Make sure that the mounting clamp or “L” bracket is tight before leaving the dock.
Decide early what type of LED lighting you want (if any) and wire accordingly
(NOTE: if you want “Dancing Light” look to the WiFi or RF or BT remote- controlled LED light box. The easy way to have lighting … YOUR way!

INSTALLATION EQUIPMENT

An Electric Drill With Bits
Allen / Hex Key / Wrench Set
Philips Head And Standard Screw Drivers
Wire Strippers
Crimping Tool
Vom (Electronic Volt Ohm Meter)
Heat Shrink Tubing And Heat Gun
Soldering Iron
Electronic (Rosen Not Acid Core) solder

BEGINNING MOUNTING

Step 1: Install your preferred speaker on the tower by connecting the speaker cables inside and then securing it with the supplied mesh and screws.
Step 2: Find a GOOD location that allows for easy wiring of the speaker (and LED lights) -PLUS does NOT impair your movement around the location.
Step 3: Using the supplied 6mm hex wrench spin out the 4-M8 screw that holds the top clamp
Step 4: Drill a 015 – 020 mm hole on the mounting tube bottom and align the clamp wire out hole.
Step 5: Connect the speaker wire AMP out and LED controller, Insulated lock the clamp to the tube.
Step 6: Cut the length of the rubber pad and wires outlet according to the diameter of the installation pipe
Step 7:Wrap the rubber pad around the pipe and align the wire out the hole According to the diagram.

Step 8: Push the wire into the tube, press on the rubber pad, and lock the top clamp.
Step 9: Take down the safety rope and hang it on the pipe, lock the screw gasket safety rope lifting ring on the clamp base, and apply screw fastening glue on the screw before locking.
Step 10: If need be, rotate the speakers for best dispersion, this is easily done by locating the 6mm & 4mm hex wrench set screw on the side of the clamp base, rotate the speaker/enclosure to the desired angle, once there… locking the screws tight. Avoid vibration, clamp loose!!!

****Step 11: During the mounting process, you should have located the spot to drill your tower bar for the 6 conductor wire (Speaker and RGB lightning wiring) insertion. Or NOT (see Tie-wrap solution below)
Step 12: Remove Wire NBR Plug and Slide the wire through the hole Snake the wire down to the bottom of the tower tube in a location where the wires can be attached to the audio (And lighting) system. A solder or butt connects the speaker wire coming from the tower to the speaker wire to the system. Then heat-shrink it for added protection from water/moisture.

Step 13: When you want to install a flat mounting, remove the clamp and take out the 6 core through it into the flat mounting bracket, then assemble it, see depiction below.

INSTALLATION & CONNECTION OPTION
If you have an LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:

To conned without LED Control Module (LED-BTC), Conned as Shown in the Following Diagram:

Black wire”BR” connected to batten/ Positive (+) 12V
White Color Light “R”; “B” and “G” connected to battery Negative (-)
Green Color Light “G” connected to battery Negative (-)
Red Color Light “R” connected to battery Negative (-)
Blue Color Light “B” connected to battery Negative (-)
Purple Color Light “R” and “B” connected to battery Negative (-)
Yellow Color Light”R” and “G” connected to battery Negative (-)
Cyan Color Light “B” and “G” connected to battery Negative (-)

SPECIFICATIONS

BODY FEATURES

Nominal Diameter …………………………………….. 10″ / 254mm
Marine Grade …………………………………………………………………………….. IP65
UV Compliant……………………… Yes, 100%Stable
RGB LED…….. _Integrated RGB LED Speaker Lighting, Integrated RGB LED Acrylic Ring Lighting
Wiring/Connections ……………. 6 Core Wires for Lighting and Speaker
Enclosure Material …………. Injection PC+ABS
Grill Material …… Injection Molded Composite with 316 Metal mesh
Clamp ………………. Die-Cast Adjustable (1″-2″) 360 Degree Rotation Mounting Buried Wire or Open Wire Mounting Optional, Included NBR Pad And Stainless Hardware (Screws, Stop Washers, Hexagon wrench, Safety Rope, Screw fastening Glue)

Enclosure Material …………. Injection PC+ABS / Injection PC+ABS
Front Logo……………………………… Yes, can be rotated for correct angle display
Rear Logo ………………….. Yes, can be rotated for correct angle display
Sold as Pair……………………………………………………………. Yes

Color & Finish / Color y Acabado ……… Glossy Carbon Fiber Texture / Textura Brillante de Fibra de Carbon

TOWER MEASUREMENT

Overall Diameter…………………………………………10.76″ / 273.3mm
Overall Depth …………………………………………..15.2″ / 386.4mm
Overall Height (with clamp) …………………..14.32″ / 364mm
Mounting Hole Diameter…………………………8.6″ / 220mm
Overall Diameter ……………………………………………10.76″ / 273.3mm

SPEAKER MEASUREMENT
Mounting Hole Diameter …………………………. 8.6″ / 220mm
Overall Diameter ………………………………………………………………. 10.76″ / 273.3mm
We LIKE IT LOUD