DS18 NXL-10 10 Inch Marine Grade Coaxial Speaker Owner’s Manual

Advantium Built-In Wall Oven 120V
Owner’s Manual

FEATURES

• 10″ 2-Way Speaker for Marine & Motorsports.
• Continuous Power Handling 200W RMS Each.
• Peak Music Power 600W MAX Each.
• Sensitivity: 94.3dB at 1W/1M.
• Nominal Impedance: 4 Ohm.
• Frequency Response: 35Hz – 20KHz
• IP65 Marine Grade Compliant Specifications, 100% UV Stable.
• Sold as Pair.

COMPONENTS

• Coaxial Separate with Floating Design.
• Motor Structure Use Y35 Ferrite Main Magnet and Reverse N35 (Neodymium) Magnet.
• 25mm PEN Dome Tweeter.
• Copper ring utilized in motor structure for far-field performance.
• integrated LED-RGB Lighting.

MATERIALS

• Injected Molded Polypropylene Cone with UV Protection.
• Soft PC Damping Glued Surround.
• PC injection Molded Composite Basket with UV Coating.

BT Control Module & App (LED-BTC) For Multi-Function for RGB LED Lighting (sold separately).

PACKING INCLUDES

• 2 x 10″ 2-Way Full Range Speaker For All Elements Marine (1 per box) .
• 2 x 1.5M #18 Speaker Input Wired With Fast Terminal.
• 2 x 1.5M #22 RGB Power Input Wired With Fast Terminal.
• 12xM4 Phillips inner Hex Head 304 Stainless Steel (4mm Hex Tool).

READ BEFORE INSTALLATION

1. Be sure to carefully read and understand the instructions before attempting to install these speakers.
2. For safety, disconnect the negative battery terminal from the battery prior to beginning the installation.
3. For easier assembly, we suggest you run all wires prior to mounting speakers in place.
4. Use high-quality connectors for a reliable installation and to minimize signal or power loss.
5. Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines, or electrical wiring when working on any vehicle. If installing in a boat, take care not to cut or drill through the main hull.
6. Never run wires underneath the vehicle. Running the wires inside the vehicle or hull area provides the best protection.
7. Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the firewall.

INSTALLATION

1. Determine where the speakers will be mounted.
   Ensure an area large enough for the speaker to mount evenly. Be sure that the mounting location is deep enough for the speaker to fit: only mount to a flat surface. Use extra caution when mounting on panels with urethane foam.

2. Refer to the specification chart to determine the proper diameter hole to cut for the speaker.

3. Mark the locations for the mounting screws. Drill the holes with a 0.75″ bit.

4. Feed the speaker wires through the cutout and connect to the speaker terminals. Be sure to 0observe proper polarity when connecting the 0wires. The speaker’s positive terminal is indicated with a “+”.

5. Fit the speaker and mount it into place using six (6) screws.

6. Tighten the screws until the speaker is snug 0in place.

7. LED CONNECTIONS – There are two options to choose from:

WIRING

1. lf you have an LED Control Module (LED-BTC), Connect as shown in the following diagram:
2. To connect without LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:

1. Green Color: “G” Fast Terminal Connect to Battery Negative.
2. Red Color: “R’ Fast Terminal Connect to Battery Negative..
3. Blue Color: “B” Fast Terminal Connect to Battery Negative.
4. Purple Color: “R” And “B” Fast Terminal 0Connect to Battery Negative.
5. Yellow Color: “R’ And “G’ Fast Terminal 0Connect to Battery Negative.
6. Cyan Color: “B” And “G” Fast Terminal 0Connect to Battery Negative.
7. While Color:”R’ And ‘B’ And “G’ Fast Terminal Connect to Battery Negative.

EXAMPLE OF GREEN LIGHT CONNECTION:

EJEMPLO DE CONEXIÓN DE LUZ VERDE:

SPECIFICATIONS

GENERAL SPECIFICATIONS
Nominal Diameter…………………………………………… 10″ / 254 mm
Nominal Impedance………………………………………………………… 4 Ohm
RMS Power Handling ………………………………………. 200 Watts
MAX Power Handling…………………………………….. 600 Watts
Sensitivity (1w/1m)…………………………………………………….. 94.3 dB
Frequency Response ……………………………………………….. 35Hz-20KHz
Recommended Hi Pass Crossover………………………….50Hz

BODY – FEATURES
UV Compliant……………………………. Yes, 100% Stable
Marine Grade Type…………………………………………………………. IP65
RGB LED……………………………………………. Yes, RGB integrated
Grill Type………. Injection Molded Composite ASA with UV Protection Coating
Pair………………………………………………………… Yes

WOOFER SPECIFICATIONS
Voice Coil Diameter ……………………….. 1.5″ / 38.6mm
Voice Coil Former Material……………………………… Kapton
Winding Material……………………………………….. CCA
Cone Material………….Injection Molded Polypropylene + UV Compliant
Surround Material………………………………………….Butyl (Rubber) / Goma
Basket Material…………………………………… High Temp Injection Molded
Magnet Material……………………………… Ferrite (Y35) + Neodymium (N35)
Magnet Weight…………………………………………………. 50 OZ + 0.56 OZ

TWEETER SPECIFICATIONS
Voice Coil Diameter……………………………………………………1″ / 25mm
Voice Coil Former Material………………………………………….. Kapton
Winding Material……………………………………………………….. CCAW
Diaphragm Material…………………………………………………..PEN
Magnet Material…………………………… Neodymium (N38H) / Neodimio (N38H)
Magnet Weight………………………………………………………….. 0.51 OZ

THIELE & SMALL PARAMETERS
Equivalent Volume……………………………..Vas …………………. 197.13L / 6.96ft3
Excursion (one way)…………………………… Xmax ……………………………………. 6 mm
Free Air Resonance…………………………..Fs ……………………………………. 42 Hz
Mechanical Factor………………………………..Qms ……………………………………. 6.874
Electrical Factor……………………………………… Qes ……………………………………. 0.838
Total Factor…………………………………………..Qts ……………………………………. 0.747
Moving Mass……………………………………. Mms ………………………………….. 11.37g
Compliance………………………………… Cms ………………………….1.264 mm/H
Bl Factor…………………………………………………… Bl ………………………………………… 3.4
Voice Coil Inductance………………..Le ………………………….. 0.60712mH
Diaphragm Area…………………………………….. Sd ………………………….. 333.29 cm2
DC Resistance………………………………………. Re ……………………………….. 3.2 OHM
Efficiency Bandwidth Product……………………….EBP …………………… 50.12

SPEAKER MEASUREMENTS
Overall Diameter………………………………………………………. 10.7″ / 274 mm
Overall Depth……………………………………………………………………. 5.7″ / 144.7 mm
Front Mount Baffle Cutout……………………………………. 8.75″ / 222 mm
Mounting Depth………………………………………………… 4.2″ / 106.6 mm
Motor Diameter…………………………………………………………………5.3″ / 135 mm

COLORS AVAILABLE
Black Satin…………………………………………… NXL-10/BK
White Gloss………………………………………. NXL-10/WH

WARRANTY

Please visit our website DS18.com for more information on our warranty policy

DIMENSIONS

We reserve the right to change products and specifications at any time without notice.
Images may or may not include optional equipment.

FOR MORE INFORMATION PLEASE VISIT
DS18.COM

Documents / Resources

| DS18 NXL-10 10 Inch Marine Grade Coaxial Speaker [pdf] Owner's Manual
NXL-10, 10 Inch Marine Grade Coaxial Speaker, NXL-10 10 Inch Marine Grade Coaxial Speaker, Marine Grade Coaxial Speaker, Grade Coaxial Speaker, Coaxial Speaker, Speaker
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>