QOTO QT O5M Smart Water Valve User Manual
- June 5, 2024
- QOTO
Table of Contents
QOTO QT O5M Smart Water Valve
User Manual
Smart Water Valve(Zigbee)
Performance and instructions
- Smart water valve
Remote operation: remote control of mobile APP anytime and anywhere, manual control of field devices, and timing control of APP Signal distance: the open distance between gateway and the smart water valve is ≤50 meters
Battery:2* AA Ni-MH rechargeable batteries Protection grade: IP66. A smart water valve can be installed and used outdoors.
Instructions for use:
- One gateway can be connected with 8 smart water valves.
- The open distance from the gateway to the smart water valve is ≤100 meters, (determined according to the actual installation environment).
- Zigbee signal cannot be relayed and jumped through smart water valve.
- Please install the timer under the sun, so that the solar panel can power the batteries.
- The App will record the statistics only if the smart valve is online.
- To prevent water into the battery case, please keep the cover closed correctly by screwing the bolts tightly.
- Winterization protection is needed when the temperature is under 0°C, frost damage is not in the warranty coverage.
Product parameters
Model| QT-05M
Caliber| ½”&¾”
Waterproof level| Ip66
Withstand water pressure| 0~10bar
Power| 2* AA Ni-MH
rechargeable batteries
Product
name| QWT-02(Zigbee)
Operating
temperature| -10℃~+50℃
Working
humidity| 0-90%RH
No condensation
Power
Signal| DC5V/1A
range| pen area ≤ 100 meters
Operation Guide
①Scan the QR code to download the “Smart Life” app,
②Register a member account.
Input your mobile phone number or email address. Receive the verification code
SMS. Configure your own password.
https://smartapp.tuya.com/smartlife
Gateway networking tutorial
- Open the APP and click add device or “+” in the upper right corner,
- Select gateway central control → wireless gateway (Zigbee),
- Enter WiFi account and password (2.4Ghz),
- Check to confirm that the indicator light is flashing, and EZ mode is in the upper right corner,
- Next, enter the interface of adding equipment,
- Wait a moment and add successfully.
Gateway adds and connects intelligent water valve
- Open the gateway interface and select “+Add Subdevice”.
- Confirm whether the indicator light of the intelligent water valve flashes (press and hold the switch button of the intelligent water valve for 5 seconds, and the indicator light switches from long on to flash or extinguish).
- Automatically search for equipment, and click Finish after searching for the equipment.
- If the addition is successful, click the name of the brush to modify it.
Mobile APP Interfac e
It’s easy to understand and operate
Warranty Regulations
-
The warranty period of this product is one year.
-
During the warranty period, any failure that occurred under normal use according to the instruction manual (judged by the official staff of our company) shall be repaired free of charge.
-
During the warranty period, if one of the following situations occurs, it must be repaired as a charge:
① This guarantee and valid purchase certificate cannot be provided.
②Faults and damages caused by incorrect use and improper repair by oneself.
③Failure or damage caused by transportation, moving, and falling after receiving goods.
④ Damage caused by other inevitable bad factors.
⑤Failure or damage caused by equipment soaking in water.
⑥If the temperature is lower than 0℃, please disassemble and put it back indoors. If the equipment is damaged due to this problem, there is no warranty. -
We only make the above warranties and do not make any other express or implied warranties (including implied warranties of merchantability, rationality and adaptability to a specific application, etc.). Our company is not responsible for any special, accidental or indirect damages, whether in contract, civil negligence or other aspects.
FCC Caution.
§ 15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
§ 15.21 Information to the user.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
§ 15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed nd used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: -Reorient or relocate
the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning for Mobile devices:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>