Insets Ev4i E-Touch Inset Electric Fire Instruction Manual

Insets Ev4i E-Touch Inset Electric Fire

EU DIRECTIVES

All EvAll Evonic Fonic Firires pres products meet the products meet require requirements movements of the EC Dir the EC Directivectiveses.. These dishes directives has have been met be been met by compliance with the fy compliance with the following stand following standards:ds:
EU 2011-65/EU 2015/863 REU 2011-65/EU 2015/863 Restriction restriction of Hazar Hazardous Substancesdous Substances.. RRefefererences to the rences to the relevant designate designated standard standards used:ds used:

• EU 2011-65/EU 2015/863 Restriction of Hazardous Substances.
  References to the relevant designated standards used:

• EN 55014-1:2006 + A1:2009 +A2:2011 Electromagnetic Compatibility.

• EN 55014-2:2015 Electromagnetic Compatibility.

• EN 61000-3-2:2014 Electromagnetic Compatibility (EMC). Limits. Limits for Harmonic Current Emissions.

• EN 61000-3-3:2013 Electromagnetic Compatibility (EMC). Limits. Limitation of Voltage Changes, Voltage Fluctuations and Flicker.

• EN 60335-1:2012+A11:2014 Household and similar electrical appliances – Safety

• EN 60335-2-30:2009+A11:2012 Household and similar electrical appliances. Safety. Particular requirements for room heaters

UKCA STANDARDS

All EvAll Evonic Fonic Firires pres products are in conformity with the enormity with the relevant UK Staant UK Statutory Instrtutory Instrumentsuments (and their amendments).(and their amendments).

• 2016 No. 1101 The Electrical Equipment (Safety) Regulations 2016
• 2016 No. 1091 The Electromagnetic Compatibility Regulations 2016
• 2012 No. 3032 The Restriction Of Use Of Certain Hazardous Substances In
  Electrical And Electronic Equipment Regulations 2012

IMPORTANT INFORMATION AND HEALTH & SAFETY

• Read all of the instructions carefully before using the appliance, only use this appliance as described in this manual. Any other use, not rAny other use not recommended by the many manufacturer mar may cause injury to because injury to person sons, or dama, or damage to the ae to the appliance.
• Remove all packaging and dispose of it at an appropriate recycling facility.
• When trWhen transporting sporting or storing the aging or storing the appliance and appliance and power lead, keep in a dry place in a dry place, a, away from excessive fiber vibration and distortion and store so as to ae so as to avoid damaged damage.
• Do not install this appliance immediately in front of a fixed socket outlet.
• Do not install this appliance in the immediate surroundings of a bath, shower, swimming pool or any other area where the appliance could come into contact with water or humidity, e.g. a bathroom.
• Do not use in Ardo not use in areas where gasoline, paint, or any f, paint, or any flammable liquids are used or store used or stored. ed.
• This appliance is only suitable for indoor use, do not use outdoors.
• Do not cover the appliance, or let the air inlet/outlet to be obstructed in any way as it may overheat.
• Keep the power lead away from hot surfaces and hot conditions, including the heater outlet. Do not route the power lead in front of the appliance, or under any carpets or rugs.
• Always use a certified electrician should new circuits or outlets be required, and always use properly grounded, fused and polarized outlets.
• Where the power lead passes through any masonry wall, stone surround etc. ensure that suitable rubber bushes are fitted at any possible wear points.
• If the power lead is damaged do not use the appliance until it has been replaced.
• Do not use any external switching device, timers, or extension leads. Do not connect the appliance to a circuit that is frequently switched on and off by the utility.
• In the eIn, the event often of a malfunction, s a malfunction, witch of the appliance, and disconnect it fr, and disconnects it from them the main power supply. Ha. Have the ae the appliance inspected by a very certified electrician befield electrician before reusing
• Do not use the appliance if it is damaged. In the event of any damage to the appliance, please contact the retailer from whom the appliance was purchased.
• Any repairs must only be performed by a certified electrician.
• This appliance can be used by children aged 8 years and above, and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children under the age of 3 years should be kept away from the appliance unless supervised.
• Disconnect frDisconnect from the power supply before perfer performing any coming to any cleaning, maintenance or, maintenance or relocalization oftion of the unit. Do not use steam c the unit. Do not use steam cleaners or are, or aerosols near the appliance
• Do not burn wood or anything else in this appliance.
• Do not strike the glass.
• Do not drill or screw any new holes into the appliance.

 COMPONENTS FOR INSETS

Name

|

Fuel Sets

| Suction Lifters| Remote Control (Optional)| Spacer (Optional)|

Frame

| Frame Fret| Installation Kit| Electrical Lead| Inset Instruction Manual
---|---|---|---|---|---|---|---|---|---
Infill Plate| Magnets| Cast Frame Fixing Kit
Colorado| Logs / Pebbles White/Beach

/ Log & Pebbles / Coals

| 2 x| YES| 75mm| 1 x| | | 4 x| | 1 x| 1 x
Ev4i| Logs / Pebbles White/Beach

/ Log & Pebbles / Coals

| 2 x| YES| | 1 x| | | 4 x| | 1 x| 1 x
Ev4i4| Logs / Pebbles White/Beach

/ Log & Pebbles / Coals

| 2 x| YES| | 1 x| | | 4 x| | 1 x| 1 x
Ev6i| Logs / Pebbles White/Beach

/ Log & Pebbles / Coals

| 2 x| YES| | 1 x| | | 4 x| | 1 x| 1 x
Ev6i4| Logs / Pebbles White/Beach

/ Log & Pebbles / Coals

| 2 x| YES| | 1 x| | | 4 x| | 1 x| 1 x
Kepler 22| Logs / Pebbles White/Beach

/ Log & Pebbles / Coals

| 2 x| YES| 75mm| 1 x| | | 4 x| | 1 x| 1 x
Oberon| Logs / Pebbles White/Beach

/ Log & Pebbles / Coals

| | YES| | 1 x| 1 x fret 2 x screws| | | 1 x| 1 x| 1 x
Strellar| Logs / Pebbles White/Beach

/ Log & Pebbles / Coals

| 2 x| YES| | 1 x| 1 x fret 2 x screws| 1 x infill 2 x screws| | 1 x| 1 x| 1 x
Argenta 16| Kindling log set| 2 x| YES| | 1 x| | | 4 x| | 1 x| 1 x
Argenta 22| Kindling log set| 2 x| YES| | 1 x| | | 4 x| | 1 x| 1 x
Sphera| Kindling log set| 2 x| YES| | 1 x| | | 4 x| | 1 x| 1 x
Topaz| Logs / Pebbles White/Beach

/ Log & Pebbles / Coals

| | YES| | 1 x| | | 4 x| | 1 x| 1 x

OPERAOPERATING INSTRUCTING INSTRUCTIONS

Manuale
Remote Contremote Control

MANUAL OPERATION

• You can operate your appliance using the manual rocker switches located on the right-hand side.
  Please note there is no manual dimmer control.

• To turn on the appliance and activate the flame effect, press the top rocker switch to the I/On position.

• To activate the heater at Low Heat, press the middle rocker switch to the I position. To deactivate, switch the rocker switch back.

• To activate the heater at High Heat, press the bottom rocker switch to the II position. To deactivate, switch the rocker switch back.

• To turn off the heater and flame effect, press the top rocker switch to the O/Off position.

• If your appliance is fitted with a thermostat you can adjust the heat output by turning left to decrease the heat, and right to increase the heat.

REMOTE CONTROL OPERATION

• You can operate your appliance using the optional remote control. Ensure that the rocker switch on the appliance is in the I/On position, then you can use the remote to control the appliance.

• To turn on the flame effect, press the top left button.

• To activate the heater at Low Heat, press the bottom left button.

• To activate the heater at High Heat, press the bottom right button.

• To turn off the heater and flame effect, press the top right button.

• To activate the dimmer function, press the large bottom button once to start, and then again to stop at the desired dimmer setting.

• To turn off the appliance, press the rocker switch on the appliance to the O/Off position.

INSTINSTALTION

MODEL DIMENSIONS
The model shown in these drawings is a Colorado for illustrative purposes, please refer to the table for your specific models size.

MODEL DIMENSIONS

Model

| Width| Height| Depth
---|---|---|---
Overall (A)| Insert (B)| Overall (C)| Insert (D)| Overall (E)| Insert (F)| Frame (G)
Colorado| 460mm| 382mm| 605mm| 550mm| 130mm| 75mm| 55mm
Ev4i| 480mm| 382mm| 590mm| 550mm| 145mm| 75mm| 70mm
Ev4i4| 480mm| 382mm| 620mm| 550mm| 145mm| 75mm| 70mm
Ev6i| 625mm| 382mm| 590mm| 550mm| 145mm| 75mm| 70mm
Ev6i4| 625mm| 382mm| 645mm| 550mm| 145mm| 75mm| 70mm
Kepler 22| 645mm| 382mm| 605mm| 550mm| 135mm| 75mm| 60mm
Oberon| 515mm| 382mm| 615mm| 550mm| 200mm| 75mm| 125mm
Strellar| 515mm| 382mm| 615mm| 550mm| 200mm| 75mm| 125mm
Sphera| 475mm| 382mm| 600mm| 550mm| 204mm| 75mm| 50mm
Argenta 16| 464mm| 382mm| 590mm| 550mm| 127mm| 75mm| 52mm
Argenta 22| 638mm| 382mm| 605mm| 550mm| 125mm| 75mm| 50mm
Topaz| 645mm| 382mm| 605mm| 550mm| 135mm| 75mm| 60mm

INSTALLATION PROCESS

INSTINSTION Slide inSlide in

INSTALLATION

All our inset models are designed to be fitted into a standard 16” wide x 22” high opening. Before starting the installation check the dimensions of both the appliance and your opening to ensure that they align well.
Please note, if you are installing into an existing chimney breast it is imperative that the flue is adequately blocked off.

SLIDING IN

Once the dimensions have been checked, attach the electrical lead to the power inlet on the back lower right. Connect the electrical lead to the mains power, then slide the appliance into the prepared opening.

INSTINSTALTION Tie Bacie Back Modelsk Models

Oberon| Strellar|
---|---|---

All our inset models are designed to be fitted into a standard 16” wide x 22” high opening. Before starting the installation check the dimensions of both the appliance and your opening to ensure that they align well.
Please note, if you are installing into an existing chimney breast it is imperative that the flue is adequately blocked off.

STRELLAR INFILL PLATE

Our Strellar model comes with an infill plate and 2x screws, if you have an Oberon model you can skip to the section below and continue with the installation.
To fit the Infill plate, screw in the two screws to either side of the plate as shown. This lines up with the two screw holes on the front of the appliance.
You can now continue the installation in the below section.

STRELLAR & OBERON INSTALLATION

First attach the electrical lead to the power inlet on the back lower right, and plug into the mains power. Using the Cast Frame fixing kit, drill and fit the x 2 wall plugs and x 2 screw eyes to the inside of the wall opening. Then using the cable, form a loop by threading it through one of the holes on the front of the appliance, then through the eye screws, and back through another hole on the appliance. You can use the most conveniently positioned hole on the appliance for your installation. Now move the appliance into the opening, pulling the solid end of the cable against the appliance. Feed the barrel clamp onto the open end of the cable, and whilst maintaining tension screw it tight.
Cut the cable approximately 50mm away from the barrel clamp.

INSTINSTALTION With SpacerWith Spacer

Colorado| Kepler 22|

---|---|---

INSTALLATION

To convert your appliance to a free-standing unit you can fit an optional spacer.
Before securing the spacer, attach the electrical lead to the inlet at the back bottom corner of the appliance. Once the spacer is fitted it will be more difficult to attach this.
Position the spacer at the back of the appliance and line up the three screw holes on both appliance and spacer. Then screw in your three screws as shown below. The electrical lead can then slot into the semi circular hole, allowing the appliance to sit free-standing on the floor.

INSTINSTALTION Wall Mountedall Mounted

Ev4i4| Ev6i4| Topaz

---|---|---

All our inset models are designed to be fitted into a standard 16” wide x 22” high opening. Before starting the installation check the dimensions of both the appliance and your opening to ensure that they align well.
Once the measurements are confirmed, plug in the appliance and slide it into the prepared opening. The appliance can then be screwed to the wall with the four screw holes as shown below.

REMOREMOVING THE GIVING THE GLASSES

1. Unscrew the two screws, and remove the bottom glass retainer from the appliance.
2. The glass can now be removed from the appliance. To replace the glass, follow the steps in reverse.

Share

1. Unscrew the two screws, and remove the top plate.
2. With the top plate now removed, slide the glass upwards to remove.

FUEL SETS

Once your appliance is installed and any front glass is removed you can lay out your fuel set as you wish. Then replace any glass panel by reversing the glass removal steps.

FITTING THE FASCIA

MAGNETS
The following models have a fascia attached with magnets;

• Argenta 16
• Argenta 22
• Colorado
• Ev4i
• Ev4i4
• Ev6i
• Ev6i4
• Sphera
• Kepler 22
• Topaz

SLOTTED

The Oberon and Strellar cast fascia is secured to the front of the appliance with two top mounted clips and a mounting bracket. Line up the two clips with the top of the mounting bracket and slot them down into the bracket.

The cast frame can now be screwed to the appliance using the 2x screws supplied. The screw holes are located at the lower part of the frame. Once these are fitted, the fret panel can be fitted in front of this.

TROUBLESHOOTING

Applies to; Colorado / Ev4i / Ev4i4 / Ev6i / Ev6i4 / Kepler 22 / Oberon/ Strellar / Topaz / Argenta 16 / Argenta 22
Colorado Blower Access & Clean
Scan the QR code to be taken to a video in our maintenance series.

REPORT A FAULT
If you have any difficulties or problems with your appliance then please get in touch so that we can assist you. Please scan the QR code to be taken to our website’s Report a Fault page, we will then be in touch with you shortly.

WARRANTY

The above warranty terms and conditions, as of 1st May 2022, are applicable for all relevant products purchased after this date. Appliances despatched prior to this date will have an alternative warranty as set out within the Installation and User Instructions that was supplied with the product, this was usually a standard 2-year warranty.
To receive your Extended Warranty your Evonic Fires product must have been purchased from an authorised stockist within our Retailer Network and your warranty registered with Evonic Fires through the online form – evonicfires.co.uk/register-your-product. The commencement date for the warranty period is the date of purchase.
The product must be adequately serviced and maintained. Evonic Fires provide maintenance call outs at a cost, and information on this can be obtained by contacting our head office. Please see your Evonic Installation Instructions for further information on how to service and maintain your appliance.
During your extended warranty period, only parts supplied or authorised by Evonic Fires can be used to repair your fireplace, and these spare parts can be obtained by contacting our service department at service@evonicfires.co.uk or calling 01789 263868.
Consumable items such as glass, screens, LED’s, LED boards, filters and power supplies which are either subject to normal wear and tear or parts that require replacement in connection with normal maintenance are not covered within the extended warranty. These items are covered for the first 12 months.
To make a warranty claim, evidence must be supplied to our service department in the form of pictures, videos, or both. Failure to supply evidence to support your warranty claim may invalidate or delay the claim. Any visit by an Evonic Fires engineer will incur a service charge after the first year. We will not accept or reimburse the cost(s) of any third party who undertakes any work carried out on the product or fits parts, unless we have approved such work in advance of it being carried out.

WARRANTY EXCLUSIONS AND LIMITATIONS

The Evonic Extended Warranty does not cover:

1. Damage resulting from installation and usage where the appliance has not been installed or used in accordance with the CK Fires Ltd installation and operation instructions, or if the installation does not conform to local building, fire, and safety regulations.
2. Issues with mains/spur connections of power supply.
3. Damage resulting from the product not being adequately maintained. (Please see your CK Fires Ltd Installation and Operating Instructions for further information on how to service and maintain your appliance).
4. Damage caused by unauthorised modifications, use or repair.
5. Damage or defects caused by the product being stored in a damp, unheated environment.
6. Consequential loss (to the extent permitted by the law) relating to other associated products that have not been supplied by CK Fires Ltd.
7. Consequential loss (to the extent permitted by law) related to decorations, furnishings, or other household assets.
8. Removal and re-installation costs.

WARRANTY EXCLUSIONS AND LIMITATIONS

Repaired or replaced products are covered only for the remainder of the original warranty period. In the event of a claim being made, this must be reported to your retailer or CK Fires Ltd within 14 days of the fault occurring/being noticed. In the event of a product fault occurring during the warranty period years 2-5, CK Fires Ltd will send the appropriate component or goods necessary to rectify the fault, free of charge.
Nothing in the Extended Warranty shall make CK Fires Ltd liable for any or special, incidental, or consequential damages, injury to persons or property, or any other consequential loss beyond the consumer’s statutory rights. The liability on these issues is covered by our Terms and Conditions of Sale.
CK Fires Ltd total liability extends only to the purchase price paid for the goods, except where such a limitation is prohibited by statute. CK Fires Ltd, in the event of a warranty claim, reserves the right either to replace the goods in question or to refund the purchase price of the goods. For product sold outside the UK and Ireland, UK law will prevail.
The Evonic Fires Extended Warranty does not affect your statutory rights.

CK Fires Ltd / Evonic Fires
1, Evonic House, Clifford Park, Clifford Lane, Stratford-on-Avon, CV37 8HW
Tel: +44 (0)1789 263868 Fax: +44 (0)1789 293080 Email: sales@evonicfires.co.uk
www.evonicfires.co.uk
Follow us on:
Instagram | Facebook | Twitter | LinkedIn
@evonicfires

References

• Register Your Product - Evonic Fires
• Electric Fires, Stoves & Inset fires - Evonic Fires

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>