HOVER-1 i-200 SELF-BALANCING electric scooter Instruction Manual
- June 5, 2024
- HOVER-1
Table of Contents
1 i-200 SELF-BALANCING electric scooter
Instruction Manual HELMETS SAVE LIVES!
Always wear a properly fitted helmet that complies with CPSC or CE safety standards when you ride your scooter.
| Correct Fitting:
Make sure your helmet covers your forehead.
---|---
| Incorrect Fitting:
Forehead is exposed and vulnerable to serious injury.
WARNING!
PLEASE READ THE USER MANUAL THOROUGHLY.
Failure to follow the basic instructions and safety precautions listed in the
user manual can lead to damage to your i-200, other property damage, serious
bodily injury, and even death.
Thank you for purchasing the Hover-1 i-200 Electric Scooter. Please read all
instructions carefully before using and retain this manual for future use and
reference.
This manual applies to the i-200 Electric Scooter.
- In order to avoid dangers that are caused by collisions, falls, and loss of control, please learn how to ride the i-200 safely.
- You can learn operating skills by reading the product manual and watching videos.
- This manual includes all operating instructions and precautions, and users must read it carefully and follow the instructions.
- Hover-1 can not be held liable for damage or injury caused by failure to understand and follow the warnings and instructions in this manual.
ATTENTION
-
Use only the supplied charger with this scooter.
Charger Manufacturer: DONGGUAN GREEN POWER ONE CO.,LTD
Model: GA09-4200400US -
The operating temperature range of the i-200 is 32-104° F (0-40° C).
-
Do not ride on icy or slippery surfaces.
-
Read the user manual and warning labels before riding.
-
Store the i-200 in a dry, ventilated environment.
-
When transporting the i-200, avoid violent crashes or impacts.
LOW-TEMPERATURE WARNING
Low temperature will affect the lubrication of moving parts inside the i-200
scooter, increasing internal resistance. At the same time, in low
temperatures, the discharge capacity and the capacity itself of the battery
will be significantly decreased.
Use caution when riding the i-200 in cold temperatures (below 40 degrees F).
Doing so may increase the risk of mechanical failures of the scooter, which
may lead to damage to your i-200, other property damage, serious bodily
injury, and even death.
SAFETY INSTRUCTIONS
- Keep the i-200 away from heat sources, direct sunlight, humidity, water, and any other liquids.
- Do not operate the i-200 if it has been exposed to water, moisture, or any other liquids to prevent electric shock, explosion, and/or injury to yourself and damage to the i-200.
- Do not use the i-200 if it has been dropped or damaged in any way.
- Repairs to electrical equipment should only be performed by the manufacturer. Improper repairs void the warranty and may place the user at serious risk.
- Do not puncture or harm the exterior surface of the product in any way.
- Keep the i-200 free from dust, lint, etc.
- Do not use this i-200 for anything other than its intended use or purpose. Doing so may damage the i-200 or lead to property damage, injury, or death.
- This product is not a toy. Keep out of reach of children.
- Do not expose batteries, battery packs, or batteries installed to excessive heat, such as direct sunlight, or open flame.
- Do not allow hands, feet, hair, body parts, clothing, or similar articles to come in contact with moving parts, wheels, or drivetrain, while the engine is running.
- Do not operate or allow others to operate the i-200 until the user understands all instructions, warnings, and safety features described in this manual.
- Check with your doctor if you have a medical condition that could affect your ability to use the i-200.
- Persons with head, back, or neck ailments or prior surgeries to those areas of the body are not recommended to use the i-200.
- Do not operate if you are pregnant, have a heart condition, or have both.
- Persons with any mental or physical conditions that may make them susceptible to injury or impair their physical or mental capabilities to recognize, understand and perform all of the safety instructions and to be able to assume the hazards inherent in unit use, should not use the i-200.
NOTES:
In this manual, the above symbol with the word “NOTES” indicates
instructions or relevant facts the user should remember prior to using the
device.
CAUTION!
In this manual, the above symbol with the word “CAUTION” indicates a
hazardous situation that, if not avoided, can cause minor or moderate injury.
WARNING!
In this manual, the above symbol with the word “WARNING” indicates a
hazardous situation that, if not avoided, can cause death or serious injury.
SERIAL NUMBER
Please keep the serial number on file for warranty claims as well as proof of
purchase.
WARNING!
WARNING: Prolonged Exposure to UV Rays, Rain, and the Elements May Damage
the Enclosure Materials. Store Indoors When Not in Use.
INTRODUCTION
The Hover-1 i-200 is a personal transporter. Our technology and production
processes are developed with strict testing for each i-200 scooter. Operating
the i-200 without following the contents of this manual may lead to damage to
your i-200 or bodily injury.
This manual is designed to give you the information you need for the safe
operation and maintenance of your i-200. Please read it thoroughly before
riding your i-200.
PACKAGE CONTENTS
- Hover-1 i-200 Electric Scooter
- Wall Charger
- Operation Manual
FEATURES/PARTS
1. Fender | 5. Tire |
---|---|
2. Left Foot Mat | 6. Power Button |
3. Battery Indicator | 7. Charge Port |
4. Right Foot Mat | 8. Protective Chassis Casing |
OPERATING PRINCIPALS
The i-200 uses digital electronic gyroscopes and acceleration sensors to
control balance and motion, depending on the user’s center of gravity. The
i-200 also uses a control system to drive the motors that are located within
the wheels. The i-200 has a built-in inertia dynamic stabilization system that
can help assist with balance when moving forward and backward but not while
turning.
TIP – To increase your stability, you must shift your weight in order to
overcome the centrifugal force during turns, especially when entering a turn
at higher speeds.
WARNING
Any i-200 that does not work properly can cause you to lose control and
fall. Inspect the entire i-200 thoroughly before every ride, and do not ride
it until any problems have been corrected.
SPECIFICATIONS
Max Speed: | 44-160 lbs (20-72.5 kg) |
---|---|
Max Distance Range: | Up to 7mph (11.2 km/h) |
Max Incline Angle: | Up to 4 miles (6.43 km) |
Minimum Turning Radius: | 8° |
Age: | 0° |
Charge Time: | 8+ |
Battery Type: | Up to 6 hours |
Battery Voltage: | Lithium-ion |
Battery Capacity: | 36 V |
Power Requirement: | 2.0Ah |
Ground Clearance: | AC 100-240V, 50/60 Hz |
Platform Height: | 1.15 inches (2.9 cm) |
Tire Type: | 4.72 inches (12 cm) |
BTID: | Non-Pneumatic Solid Tires |
FCC ID: | D044460 |
2AANZ200B
CONTROLS AND DISPLAY
PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY
TURNING YOUR DEVICE ON/OFF
Power On: Take your i-200 out of the box and place it flat on the floor.
Press the power button (located on the rear of your i-200) once.
Check the LED indicator (located in the center of your i-200). The battery
indicator light should be lit, indicating the i-200 is powered on.
Power Off: Press the power button once.
MAT SENSOR
There are four sensors under the foot mats on your i-200.
When riding the scooter, you must ensure you are stepping on the foot mats. Do
not step or stand on any other area of your scooter.
The i-200 may vibrate or spin in one direction if weight and pressure are
applied to only a one-foot mat.
BATTERY INDICATOR
The display board is located in the middle of the i-200.
- A green LED Light indicates the hoverboard is fully charged.
- Red flashing LED light and beeping indicate low battery.
- Blue light indicates the board is charging.
When the LED light turns red, please recharge the i-200.
BLUETOOTH SPEAKER
The i-200 has a powerful built-in wireless speaker so you can play your music
while riding.
PAIRING THE SPEAKER
-
Turn on your i-200 and the speakers will “Ping” to announce that it’s waiting for a Bluetooth® connection. This will indicate your i-200 speaker is now in pairing mode.
-
Place the i-200 and the Bluetooth® device to which you would like to pair it within the operating distance. We recommend keeping the two devices no further than 3 feet apart during pairing.
-
Ensure Bluetooth® is enabled on your phone or music device. Refer to the manufacturer’s instructions for how to enable Bluetooth® on your device.
-
Once you have activated Bluetooth® on your device, select the option “H 1-200” from the list of available Bluetooth® devices.
-
If required, enter the PIN code “000000” and confirm the entry.
-
The i-200 will say “Paired” when successfully paired.
-
Please note, that pairing mode on the Hover-1 will last for two minutes.
If no devices are paired after two minutes, the i-200 speaker will automatically return to standby mode. -
If pairing is unsuccessful, turn off the i-200 first and re-pair following the aforementioned steps.
-
If your smartphone is out of range, or the battery is low on your
i-200, your speaker may disconnect from your smart device, and the
i-200 will say “Disconnected.” To reconnect, follow the aforementioned steps, or recharge your scooter.
NOTE: Once you have paired the i-200 speaker with a device, the speaker
will remember this device and will pair automatically when the device’s
Bluetooth® is activated and in range. You do not need to re-pair any
previously connected devices.
Your scooter can pair up to two multi-point devices. You can reconnect a
previously paired device without going through the pairing or PIN process on
up to two devices.
LISTENING TO MUSIC
Once the i-200 Bluetooth speaker is paired to your device, you can stream
music wirelessly through it. Only one speaker will play music as the other
speaker is strictly for safety alerts from your Hover-1. Select the track you
wish to listen to on your device to listen via the speaker.
All volume and track controls will be made using your music device.
Should you encounter any problems while streaming, please refer to your
device’s user manual.
BEFORE RIDING
It is important that you fully understand all elements of your i-200. If these
elements are not used correctly, you will not have full control of your i-200.
Before you ride, learn the functions of the various mechanisms on your
scooter.
Practice using these elements of your i-200 at slower speeds in a flat, open
area before taking the i-200 out in public areas.
PRE-RIDE CHECKLIST
Ensure that your i-200 is in proper working order each and every time you
ride. If a part of the scooter does not function correctly, please contact our
Customer Support Center.
WARNING
Any i-200 that does not work properly can cause you to lose control and
fall.
Do not ride an i-200 with a part that is damaged; replace the damaged part
before riding.
- Ensure the battery is fully charged before riding your scooter.
- Ensure that the screws on the front and back tires are locked firmly before each ride.
- Please wear all appropriate safety and protective gear as previously mentioned in the User Manual before operating your i-200.
- Make sure to wear comfortable clothes and flat closed-toe shoes when operating your i-200.
- Please carefully read the User Manual, which will assist in explaining the basic working principles and provide tips on how to best enjoy your experience.
SAFETY PRECAUTIONS
Different localities and countries have different laws governing riding on
public roads, and you should check with local officials to ensure you are
complying with these laws.
Hover-1 is not liable for tickets or violations given to riders who do not
follow local laws and regulations.
- For your safety, always wear a helmet that meets CPSC or CE safety standards. In the event of an accident, a helmet can protect you from serious injury and in some cases, even death.
- Obey all local traffic laws. Obey red and green lights, one-way streets, stop signs, pedestrian crosswalks, etc.
- Ride with traffic, not against it.
- Ride defensively; expect the unexpected.
- Give pedestrians the right of way.
- Do not ride too close to pedestrians and alert them if you intend to pass them from behind.
- Slow down at all street intersections and look to the left and right before crossing.
Your i-200 is not equipped with reflectors. It is not recommended that you ride in conditions of low visibility.
WARNING
When you ride in low-visibility conditions such as fog, dusk, or night, you
might be difficult to see, which could lead to a collision. In addition to
keeping your headlight on, wear bright, reflective clothing when riding in
poor lighting conditions.
Think about safety when you ride. You can prevent many accidents if you think
about safety. Below is a helpful checklist for Compact riders.
SAFETY CHECKLIST
-
Do not ride above your skill level. Ensure you have had enough practice with all functions and features of your i-200.
-
Before stepping on your i-200, make sure it is placed flat on level ground, the power is on, and the Running Indicator light is green. Do not step on if the Running Indicator light is red.
-
Do not try to open or modify your i-200. Doing so, voids the manufacturer warranty and may cause your i-200 to fail, resulting in injury or death.
-
Do not use the i-200 in a manner that would put people or property in danger.
-
If riding near others, keep a safe distance to avoid a collision.
-
Be sure to keep your feet on the pedals at all times. Moving your feet off your i-200 while driving is dangerous and may cause the i-200 to stop or veer sideways.
-
Do not operate the i-200 while under the influence of drugs and/or alcohol.
-
Do not operate the i-200 when you are restless or sleepy.
-
Do not ride your scooter off of curbs, ramps, or attempt to operate in a skate park, or empty pool. Misuse of your i-200, voids the manufacturer warranty and may lead to injury or damage.
-
Do not continuously spin in place, it will cause dizziness and increases the risk of injury.
-
Do not abuse your i-200, doing so can damage your unit and cause failure to the operating system leading to injury. Physical abuse, including dropping your i-200, voids the manufacturer’s warranty.
-
Do not operate in or near puddles of water, mud, sand, stones, gravel, debris or near rough and rugged terrain.
-
The i-200 can be used on paved surfaces that are flat and even. If you encounter uneven pavement, please lift your i-200 over and past the obstruction.
-
Do not ride in inclement weather: snow, rain, hail, sleek, on icy roads or in extreme heat or cold.
-
Bend your knees when riding on bumpy or uneven pavement to absorb the shock and vibration and help you keep your balance.
-
If you are unsure if you can safely ride on a specific terrain, step off and carry your i-200. ALWAYS BE ON THE SIDE OF CAUTION.
-
Do not attempt to ride over bumps or objects greater than ½ in.
even when prepared and bending your knees. -
PAY ATTENTION – look at where you are riding and be conscious of the road conditions, people, places, property and objects around you.
-
Do not operate the i-200 in crowded areas.
-
Operate your i-200 with extreme caution when indoors, especially around people, property, and narrow spaces.
-
Do not operate the i-200 while talking, texting, or looking at your phone.
-
Do not ride your i-200 where it is not permitted.
-
Do not ride your i-200 near motor vehicles or on public roads.
-
Do not travel up or down steep hills.
-
The i-200 is intended for use by a single individual. DO NOT attempt to operate the i-200 with two or more people.
-
Do not carry anything while riding the i-200.
-
Individuals with lack of balance should not attempt to operate the i-200.
-
Pregnant women should not operate the i-200.
-
The i-200 is recommended for riders ages 8 and older.
-
At higher speeds, always take into consideration longer stopping distances.
-
Do not step forward off of your i-200.
-
Do not attempt to jump on or off your i-200.
-
Do not attempt any stunts or tricks with your i-200.
-
Do not ride the i-200 in dark or poorly lit areas.
-
Do not ride the i-200 off-road, near or over potholes, cracks or uneven pavement or surfaces.
-
Keep in mind that you are 4.72 inches ( 12cm) taller when operating the i-200. Make sure to go through doorways safely.
-
Do not turn sharply, especially at high speeds.
-
Do not step on the fenders of the i-200.
-
Avoid driving the i-200 in unsafe places, including near areas with flammable gas, steam, liquid, dust or fiber, which could cause fire and explosion accidents.
-
Do not operate near swimming pools or other bodies of water.
WARNING
When a hoverboard and a kart (sold separately) are being used, it is NOT
ADVISABLE to ride the combo uphill. If using on a steep incline above 5-10°, a
safety mechanism built into the hoverboard will activate, which will shut down
your hoverboard automatically. If this happens, dismount your hoverboard,
place it on a flat surface, wait 2 minutes, and then power your hoverboard on
again.
WARNING
To reduce the risk of injury, adult supervision is required. Never use in
roadways, near motor vehicles, on or near steep inclines or steps, swimming
pools or other bodies of water; always wear shoes, and never allow more than
one rider.
RIDING YOUR i-200
FAILURE TO FOLLOW ANY OF THE FOLLOWING SAFETY PRECAUTIONS CAN AND MAY LEAD
TO DAMAGE TO YOUR i-200, VOID YOUR MANUFACTURER WARRANTY, LEAD TO PROPERTY
DAMAGE, CAUSE SERIOUS BODILY INJURY, AND CAN LEAD TO DEATH.
Before using your i-200, be sure to familiarize yourself with the operating
procedures.
OPERATING YOUR i-200
Make sure the i-200 is fully charged before initial use. For charging
instructions, please follow the details under CHARGING YOUR i-200.
Stand directly behind your i-200 and place one foot on the corresponding foot
mat (as described in the diagram below). Keep your weight on the foot which is
still on the ground, otherwise, the i-200 may begin to move or vibrate, making
it difficult to step on evenly with your other foot. When you are ready, shift
your weight to the foot already placed on the i-200 and step on with your
second foot quickly and evenly (as described in the diagram below).
NOTES
Stay relaxed and step on quickly, confidently, and evenly. Imagine climbing
stairs, one foot, then the other. Look up once your feet are even. The i-200
may vibrate or spin in one direction if weight and pressure are applied to
only a one-foot mat. THIS IS NORMAL.
Find your center of gravity. If your weight is distributed correctly on the
foot mats and your center of gravity is level, you should be able to stand on
your i-200 just as if you were standing on the ground.
On average, it takes 3-5 minutes just to get comfortable standing on your
i-200 and maintaining proper balance. Having a spotter will help you feel more
secure.
The i-200 is an incredibly intuitive device, it senses even the slightest bit
of motion, so having any anxiety or reservation about stepping on may Couse
you to panic and trigger unwanted movement when you first begin using your
i200, the fastest way to move in your desired direction is to focus in that
direction. You will notice that just thinking about which way you would like
to go will shift your center of gravity. and that subtle movement wild propel
you in that direction Your center of gravity determines which direction you
move, accelerate, decelerate, and come to a complete stop. As described in the
diagram below, tilt your center of gravity in the direction you wish to move
To tum, focus on the direction you wish to tum, and stay relaxed.
WARNING
Do not tum sharply or at high speeds to avoid donger Do not tum or ride
quickly along slopes as it may cause injury
As you get comfortable on the i-200, you will notice it becomes easier to
maneuver. Remember at higher speeds, it is necessary to shift your weight to
overcome the centrifugal force Bend your knees if you encounter bumps or
uneven surfaces, then dismount and carry your i-200 to a safe operating
surface.
NOTES
Try staying relaxed and focus on finding your center of gravity to maintain
full control of your i-200.
Dismounting your i-200 can be one of the easiest steps, yet when done incorrectly, may cause you to fall. To properly dismount, from a stopped position, lift one leg up and set your foot back down on the ground (STEPPING BACK). Then step off completely as described in the following diagram.
WARNING
Make sure to lift your feet completely off the foot mat to clear the i-200
when stepping back to dismount. Failure to do so may send the i-200 into a
tailspin.
WEIGHT AND SPEED LIMITATIONS
Speed and weight limits are set for your own safety. Please do not exceed the
limits listed here in the manual.
- Maximum Weight: 160 lbs
- Minimum Weight: 44 lbs
- Maximum Speed: Up to 7 mph
WARNING
Overweight exertion on the i-200 may increase the possibility of injury or
product damage.
OPERATING RANGE
The i-200 can travel a distance of up to 4 miles on a fully charged battery in
ideal conditions. The following are some of the major factors that will affect
the operating range of your i-200.
- Terrain: Riding distance is highest when riding on a smooth, flat surface. Riding uphill and/or on rough terrain will reduce distance significantly.
- Weight: A lighter user will have further range than a heavier user.
- Ambient temperature: Please ride and store the i-200 under recommended temperatures, which will increase riding distance, battery life, and overall performance of your i-200.
- Speed and Riding Style: Maintaining a moderate and consistent speed while riding produces maximum distance. Traveling at high speeds for extended periods, frequent starts and stops, idling and frequent acceleration or deceleration will decrease the overall distance.
BALANCE & CALIBRATION
If your i-200 is unbalanced, vibrating, or not turning properly, you can follow the below steps to calibrate it.
- First, place the i-200 on a flat, horizontal surface such as the floor or a table. The foot mats should be even with each other and not tilted forward or backward. Make sure the charger is not plugged in and the board is turned off.
- Press and hold the ON/OFF button for a total of 10-15 seconds. The scooter will turn on, lighting the battery indicator on the board.
- After the light flashes 5 times consecutively you may release the ON/OFF button.
- Turn the board off and then turn the board back on. Calibration will now be completed.
SAFETY ALERTS
While riding your i-200, if there is a system error or improper operation
performed, the i-200 will prompt the user in a variety of ways.
You will hear a beep sound alerting you to take precautions and cease
operation, which may make the device stop suddenly.
The following are common occurrences where you will hear the Safety Alerts.
These notices should not be ignored, but appropriate action should be taken to
correct any illegal operation, failure or errors.
- Unsafe riding surfaces (uneven, too steep, unsafe, etc.)
- When you step on the i-200 if the platform is tilted more than 8 degrees forward or backward.
- The battery voltage is too low.
- The i-200 is still charging.
- During operation, the platform self initiates to tilt due to excess speed.
- Overheating, or motor temperature is too high.
- The i-200 has been rocking back and forth for over 30 seconds.
- If the system enters protection mode, the alarm indicator will light up and the board will vibrate. This typically occurs when the battery is about to run out of power.
- If the platform is tilted forward or backward more than 8 degrees, your i-200 will power off and stop suddenly, possibly causing the rider to lose balance or fall off.
- If any or both tires are blocked, the i-200 will stop after 2 seconds.
- When the battery level has depleted below protection mode, the i-200 engine will power off and stop after 15 seconds.
- While sustaining a high discharge current during use (such as driving up a steep slope for a long period of time), the i-200 engine will power off and stop after 15 seconds.
WARNING
When the i-200 turns off during a Safety Alert, all operating systems will
halt. Do not continue attempting to ride the i-200 when the system initiates a
stop.
Turn your i-200 off and back on to unlock it from a Safety Lock.
CHARGING YOUR i-200
CHARGING THE i-200
-
Ensure that the charging port is clean and dry.
-
Make sure that there is no dust, debris, or dirt inside the port.
-
Plug the charger into a grounded wall outlet. The charging indicator light ON THE CHARGER will be green.
-
Connect the cable with the power supply ( 1 00V – 240V; 50/ 60 Hz).
-
Align and connect the 3-pin charging cable to the charging port of the i-200. DO NOT FORCE THE CHARGER INTO THE CHARGE PORT, AS THIS MAY CAUSE THE PRONGS TO BREAK OFF OR PERMANENT DAMAGE TO THE CHARGE PORT.
-
Once attached to the board, the charging indicator light ON THE CHARGER should change to red, indicating that your device is now being charged.
-
When the red indicator light on your charger turns to GREEN, then your i-200 is fully charged.
-
A full charge may take up to 6 hours. While charging, you will see a blue flashing light on the scooter, which also indicates charging.
Do not charge for more than 7.5 hours. -
After fully charging your i-200, unplug the charger from your i-200 and from the power outlet.
BATTERY CARE/MAINTENANCE
BATTERY SPECIFICATIONS
Battery Type: Rechargeable lithium-ion battery
Charge Time: Up to 6 hours
Voltage: 36V
Initial Capacity: 2.0 Ah
BATTERY MAINTENANCE
The lithium-ion battery is built into the i-200. Do not disassemble the i-200
to remove the battery or attempt to separate it from the i-200.
-
Use only the charger and charging cable supplied by Hover-1.
Use of any other charger or cable may lead to damage to the product, overheating, and risk of fire. Use of any other charger or cable voids the manufacturer’s warranty. -
Do not connect or attach the i-200 or the battery to a power supply plug or directly to a car’s cigarette lighter.
-
Do not place the i-200 or batteries near a fire, or in direct sunlight.
Heating the i-200 and/or the battery can cause additional heating, breaking, or ignition of the battery inside the i-200. -
Do not continue charging the battery if it does not recharge within the specified charging time. Doing so may cause the battery to become hot, rupture, or ignite.
To preserve natural resources, please recycle or dispose of batteries properly. This product contains lithium-ion batteries. Local, state or federal laws may prohibit the disposal of lithium-ion batteries in ordinary trash. Consult your local waste authority for information regarding available recycling and/or disposal options. -
Do not attempt to modify, change, or replace your battery.
WARNING
Failure to follow the safety precautions listed below could lead to serious bodily injury and/or death. -
Use only the charger and charging cable supplied by Hover-1.
Use of any other charger or cable may lead to damage to the product, overheating, and risk of fire. Use of any other charger or cable voids the manufacturer’s warranty. -
Do not use your i-200 if the battery begins to emit odor, overheats, or begins to leak.
-
Do not touch any leaking materials or breathe fumes emitted.
-
Do not allow children and animals to touch the battery.
-
The battery contains dangerous substances, do not open the battery or insert anything into the battery.
-
Only use the charger provided by Hover-1.
-
Do not attempt to charge the i-200 if the battery has discharged or emits any substances. In that case, immediately distance yourself from the battery in case of fire or explosion.
-
Lithium-ion batteries are considered to be hazardous materials.
Please follow all local, state, and federal laws in regards to recycling, handling, and disposing of Lithium-ion batteries.
WARNING
SEEK IMMEDIATE MEDICAL ASSISTANCE IF YOU ARE EXPOSED TO ANY SUBSTANCE THAT
IS EMITTED FROM THE BATTERY.
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: ( 1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Please note that changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
FCC INSTRUCTIONS FOR A CLASS B DIGITAL DEVICE OR PERIPHERAL
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CARE & MAINTENANCE
- Do not expose the i-200 to liquid, moisture, or humidity to avoid damage to the product’s internal circuitry.
- Do not use abrasive cleaning solvents to clean the i-200.
- Do not expose the i-200 to extremely high or low temperatures as this will shorten the life of the electronic components, destroy the battery, and/or distort certain plastic parts.
- Do not dispose of the i-200 in the fire as it may explode or combust.
- Do not expose the i-200 to contact with sharp objects as this will cause scratches and damage.
- Do not allow the i-200 to fall from high places, as doing so may damage the internal circuitry.
- Do not attempt to disassemble the i-200.
- Use only the charger provided by Hover-1.
WARNING
Avoid using water or other liquids for cleaning. If water or other liquids
enter the i-200, it will cause permanent damage to the internal components.
WARNING
Users who disassemble the i-200 scooter without permission will void the
warranty.
WARRANTY
For warranty information, please visit us at: www.hover-l.com
Affix Serial Number Label Here:|
---|---
@RideHover1
@RideHover1
@RideHover1
www.Hover-1.com
Documents / Resources
|
HOVER-1 i-200 SELF-BALANCING electric
scooter
[pdf] Instruction Manual
i-200, electric scooter, SELF-BALANCING electric scooter, SELF-BALANCING
scooter
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>