current 9050 ColorPLUS+ Smart LED Light User Guide
- June 5, 2024
- current
Table of Contents
current 9050 ColorPLUS+ Smart LED Light
IMPORTANT SAFETY INSTRUCTIONS
When using electrical products, basic precautions should always be practiced including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
- Never attempt repairs yourself, return the device to an authorized repair facility for service or discard.
- Carefully examine light after installation and BEFORE plugging it into the GFCI wall outlet. Be sure there is NO water or moisture on the light.
- Never plug in a wet cord. If a plugged in light or socket does get wet, DO NOT TOUCH IT. Instead, promptly disconnect the fuse or circuit breaker that supplies power to the light.
- Never operate a light that is damaged or malfunctioning, discontinue use immediately and return or discard.
- This is NOT a toy. Close supervision is required when any appliance is used by or near children.
- Always unplug fixture when not in use, before putting on or taking off parts, and before cleaning. Never pull the cord to unplug from GFCI.
- Do not use this light for anything other than its intended use.
- Ensure light is securely installed before supplying power to the unit.
- Do not use with an extension cord.
- Do not look directly into the LEDs.
WARNING:
Risk of Electric Shock. Plug device ONLY into to a GFCI protected receptacle.
If one is not provided, contact a certified electrician for proper
installation.
WARNING:
Risk of Electric Shock. Mount the unit at a height greater than 1 foot
from the ground surface.
SAVE THESE INSTRUCTIONS
This manual contains important safety and operating instructions for power
units
WARNING:
Drip Loops should always be used to help prevent water from traveling along
the cord and coming into contact with an electrical outlet. Drip loops must
always be below the level of the outlet. If the plug or outlet does get wet,
DO NOT TOUCH the cord. Disconnect the fuse or circuit breaker that supplies
power.
GROUNDING INSTRUCTIONS
This LED system must be powered with the supplied UL/cUL Listed power supply.
To avoid possible electric shock, power supply must be plugged into a GFCI
wall outlet that is installed and grounded in accordance with all appropriate
codes and ordinances.
LIMITED WARRANTY
Current USA, Inc. warrants this product against defects in materials and
workmanship of a period of ONE (1) YEAR from the date of original retail
purchase and is not transferable. Warranty on all Products, including
Aquariums, is limited to replacement of the product and does not cover fish
loss, personal injury, property loss or direct, incidental or consequential
damage arising to the use of this product.
Note:
Current-USA, Inc. One-Year Limited Warranty does not cover damage caused by
the following: improper installation, saltwater corrosion, electrical surges,
or modifications.
This warranty does not apply if the product has been damaged by accident,
abuse, misuse or misapplication or if the product has been modified without
the written permission of Current-USA, Inc.; or if any Current-USA, Inc. logos
have been removed or defaced.
THE WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL
OTHERS, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED. CURRENT USA, INC.
SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING BUT NOT
LIMITED TO LOST PROFITS, DOWNTIME, GOODWILL, DAMAGE TO OR REPLACEMENT OF
EQUIPMENT AND PROPERTY, AND ANY COSTS OF RECOVERING ANIMALS, PLANTS, TANKS OR
OTHER AQUARIUM RELATED ITEMS AND/OR EQUIPMENT. CURRENT USA, INC. IS NOT
RESPONSIBLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM
ANY BREACH OF WARRANTY, OR REPLACEMENT OF EQUIPMENT OR PROPERTY, OR ANY
COSTS OF RECOVERING OR REPRODUCING ANY EQUIPMENT, ANIMALS OR PLANTS USED OR
GROWN WITH CURRENT USA, INC. PRODUCTS. Some jurisdictions do not allow the
exclusion or limitation of incidental or consequential damages or exclusions
of implied warranties, so the above limitations or exclusions may not apply to
you. This warranty gives you specific legal rights, and you may also have
other rights that vary form jurisdiction to jurisdiction.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/IV technician for help .
Getting Started:
WARNING:
These products may represent a possible shock or fire hazard if improperly
installed or attached in any way. Products should be installed in accordance
with this install guide, current electrical codes and/or the current National
Electric Code (NEC).
-
Download the Aquatic VITA app
on your smart device -
Aquatic VITA app
Install LED Light
-
Slide adjustable docking legs on each side of light fixture to match the length of your aquarium.
-
Connect the 3-pin plug on the light fixture to the matching 3- pin plug on the LED controller,
-
Connect the male DC plug from the power supply to the LED controller.
-
Plug power supply into a GFCI protected AC outlet ensuring a drip loop is in place.
-
Place fixture over glass top of aquarium and adjust docking mounts as needed to fit tank.
-
You are now ready to use the LED light via the inline LED controller.
-
To activate smart mobile app features, proceed to steps 4 & 5. When in Smart Wi-Fi pairing mode, the LED light will blink. Note: the light will stop blinking after 3 minutes or when controlled via the inline controller.
LED Controller Button:
WARNING :
LED Controller is NOT waterproof. Keep in a dry place away from dripping water
or where it may drop into water.
Main control features:
- Press once (1x) to turn ON, light will display default White color spectrum (all colors 100%).
- Press and hold button 3 seconds to turn light OFF.
- To reset controller for pairing with the Vita app and mobile device, press and hold button for 9 seconds – LED light will blink red when ready for pairing and connection.
Manual Scene control:
- Press 2x to display Sunrise fade scene.
- Press 3x to display Sunrise fade scene.
- Press 4x to display Moonlight fade scene.
- Press 5x to display Rainstorm scene.
- Press 6x to display Partly Cloudy scene.
- Press 7x to display Sunset scene.
- press 8x to display Glow scene.
- Press 9x to display Stream scene.
- Press 10x to display Deepwater scene.
- Launch and use the Aquatic VITA app to complete the set up.
- Open the VITA app.
- Complete the requested information to create a new account, or sign into your existing account.
- Tap Add Device or the + sign, then select “Color Plus Aquarium LED” and confirm. Then enter your Wi-Fi network & password.
- Light must be rapidly blinking to connect. If not already blinking, press and hold the button on the controller for nine seconds to put light in pairing mode. Be sure to connect to a 2.4 GHz Wi-Fi network that covers your installation location.
LED controller will then pair with your mobile device (this can take 30-60
seconds).
(OPTIONAL) Connect to Alexa or Google Assistant using the in App guide
TROUBLESHOOTING TIPS CONNECTING TO WI-FI
If you are having difficulty connecting:
- Make sure the Wi-Fi network is a 2.4 GHz network. Smart Strip Light will not connect to a 5 GHz network.
- Test your Wi-Fi network with other devices such as your phone to make sure it is operating properly.
- The Wi-Fi connection may not have good coverage during set up. Try moving the Smart Strip Light closer to your Wi-Fi router.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>