Parrot Uncle F8235110V 22.5 Inch Indoor Matte Black Industrial Caged Ceiling Fan User Guide

Indoor Matte Black Industrial Caged Ceiling Fan
User Guide 

F8235110V
Installation & Operating Instructions for the Parrotuncle Owner’s Installation, Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

Safety Information

1. To reduce the risk of electric shock, the electricity has been turned off at the circuit breaker or fuse box before begin.
2. All wiring must be in accordance with the National Electrical Code NASI/NFPA 70-1999 and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
3. The outlet box and support structure must be securely mounted and capable of reliably supporting 351b.(15.9kg).Use only UL-listed outlet boxes marked “Acceptable forFan Support of 35Ibs(15.9kg)or less.”
4. The fan must be mounted with a minimum of 7 ft. (2m) clearance from the trailing edge of the blades to floor S.
5. Do not operate the reversing switch while the fan blades are in motion. You must turn the fan off and stop the blades before you reverse the blade direction.
6. Do not place objects in the path of the blades.
7. To avoid personal injury or damage to the fan and other items, please be careful when working around or cleaning the fan.
8. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL-listed and marked suitable for use with the model fan you are installing. Switches must be UL General Use Switches. Refer to the instructions packaged with the light kits and switches for proper assembly.
9. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box.
10. All setscrews must be checked and retightened where necessary before installation.

WARNING: To reduce the risk of personal injury, do not bend the blade brackets (also referred to as flanges) during assembly or after installation. Do not insert objects in the path of the blades.
WARNING: Remove the rubber motor stops on the bottom of the fan before installing the blades or testing the motor.
WARNING: To reduce the risk or fire or electric shock, do not use this fan with any solid-state speed control device.
WARNING: To avoid possible electric shock, turn the electricity off at the main fuse box before wiring you feel you do not have enough electrical wiring knowledge or experience, contact a licensed electrician.
WARNING: Electrical diagrams are for reference only. Optional use of any light kit shall be UL-listed and marked suitable for use with this fan.
WARNING: To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked’ Acceptable for fan support of 35 lbs.(15.9 kg)or less • and use the screws provided with the outlet box.

THANK YOU FOR YOUR PURCHASE
Thank you for purchasing this quality product. To ensure correct function and safety, please read and save all instructions before using the product.

SAFETY TIP

1. To avoid possible electric shock, turn the electricity at the main fuse box or circuit panel before you begin the fan installation or ON not before servicing the fan. r installing accessories
2. Read all instructions and safety information carefully before installing your fan and save these instructions.
3. Make sure all electrical connections comply with local codes or ordinances and the National Electrical Code. If you are unfamiliar with electric wiring, please use a qualified and licensed electrician.
4. Make sure you have a location selected for your fan that allows clear space for the blades to rotate, and at least seven (7) feet of clearance between the floor and the fan blade tips. The fan should be mounted at least thirty (30) inches from walls or other upright structures.
5. WARNING: The outlet box and ceiling support joist used must be securely mounted, and capable of supporting at least 100 pounds. To reduce the risk of fire, electric shock, or personal injury, mount to the outlet box marked acceptable for fan support and use mounting screws provided with the outlet box. The box must be supported directly by the building structure.
6. WARNING: To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked “acceptable for fan support” and use mounting screws provided with the outlet box most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.
7. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL listed and marked suitable for use with the model fan you are installing. Switches must be UL. general use switches. Refer to the instructions packaged with the light kits and switches for proper assembly.
8. After installation is complete, check that all connections are absolutely secure.
9. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box.
10. WARNING: To reduce the risk of electrical shock and fire, do not use this fan with any solid-state fan speed control device, or rheostat.
11. Do not separate the reverse switch until the fan has come to a complete stop.
12. Do not insert anything into the fan blades while they are rotating.
13. WARNING: To reduce the risk of personal injury, do not bend the blade brackets (also referred to as “flanges”) during assembly or after installation. Do not insert objects in the path of the blades.
14. To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning the fan.
15. Do not use water or detergent when cleaning the fan or fan blades. Dry dust cloth or lightly dampened cloth will be suitable for most cleaning.

NOTE: The important safety precautions and instructions appearing in the manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense and caution are necessary factors in the installation and operation of this fan.
NOTE: This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities are di erent or are impaired, or lack of experience or knowledge, unless such persons are supervised or trained to operate the appliance by a person responsible for their safety.
NOTE: Children should be supervised to ensure that they do not use appliances as a toy.

| Mounting screw(2PCS)
---|---
| Washer(2PCS)
| Plastic wire nut (7PCS)
| Remote control (1 PC)

Pls, check whether the above accessories are completed or not?Yes, and install.

Attaching the fan to the outlet box
WARNING: To reduce the risk of fire, electric shock, or personal A, injury, mount to an outlet box marked “Acceptable for fan support: of 35 lbs . (15.9kg) or less ,” and use the screws provided with the outlet box.
NOTE: The mounting bracket(A) is designed to slide into place on an outlet box with the outlet box screws(LL).

|
---|---

FROM POWER SOURCE AC 110- 120 VOLT 60Hz 3.5AMPS.

OPERATING YOUR FAN

Turn on the power and check the operation of the fan. The remote controller controls the fan as follows:
HI – for fan high speed
MED – for fan medium speed
LO – for fan low speed
FAN OFF -for fan off
REVERSE – for fan reversal fomard function
LIGHTIDIMMER – for light on and off (color selection).
The appropriate speed settings for warm or cool weather depend on factors such as the room size, ceiling height, and the number of fans.

Remote controller
GENERAL INFORMATION
This remote controller is designed to separately control your ceiling fan speed and light brightness.
There are four buttons (HI, MED, LOW, OFF) to control the speed of the fan and off.
The light dimmer button will control the light brightness dimmer and off.
The red indicator on the transmitter will light when one of the five buttons is pressed.
INSTRUCTION OF INSTALLATION AND OPERATION

1. SETTING THE CODES
   This unit has 16 different code combinations. To set the codes, perform the following steps:
   A. Setting the codes on the transmitter:
   a. Remove the battery cover. Press firmly on the arrow and slide the battery cover off.
   b. Slide code switches to your choice of up or down position. The factory setting is all up. Do not use this position. Use a small screwdriver or ball point pen to slide firmly up or down (Figure 1).
   B. Setting the codes on the receiver:
   a. Slide code switches to the same position as set on your transmitter (Figure

2. b. Replace the battery cover on the transmitter.

2. INSTALLING RECEIVER IN CEILING FAN
   A. Safety precautions:
   WARNING: HIGH VOLTAGE! Disconnect power by removing a fuse or switching off the circuit breaker.
   Do not use with solid state fans.
   The electrical wire must meet all local and national electrical code requirements.
   Supply for fan must be 110/120 volt, 60Hz. Maximum fan motor amps: 1.0, Maximum light watts: 180 incandescent or ballast LED.
   Otherwise, power can cause serious injury or death.
   B. Installing receiver in fan:
   a. Remove power from the circuit.
   b. Remove the ceiling fan canopy from the mounting bracket.
   c. Disconnect existing wiring between a ceiling fan and Supply in the electrical junction box.
   d. Make connections as follows, using the wire nuts supplied
   CAUTION: Ceiling Angle Shall Not Exceed 30 Degrees, For Mounting Controller, ModelRC -R28-
   CONNECT TO
   Green fan wire ….Bare supply wire
   Red receiver wire(AC IN L) ….Red supply wire
   White receiver wire(AC IN N) ….White supply wire
   White receiver wire(TO MOTOR N) ….White fan wire
   Black receiver wire(TO MOTOR L) ….Black fan wire
   Blue receiver wire(FOR LIGHT) ….Blue light wire
   Purple receiver wire(FOR REV) ….Purple rev wireIf other fans or supply wires are different colors, have this unit installed by a qualified licensed electrician.
   e. Push all connected wires up into the junction box.
   f. Lay the brown antenna wire on top of the receiver, and put the receiver into the mounting bracket.
   g. Reinstall the canopy on the mounting bracket.
   h. Restore power.

3. OPERATING TRANSMITTER:
   A. Install a 9-volt battery(not included). (To prevent damage to the transmitter, remove the battery if not used for a long time).
   B. Store the transmitter away from excessive heat or humidity.
   C. This remote control unit is equipped with 16 code combinations. In order to prevent possible interference from or to other remote units such as garage door openers, car alarms, or security systems. If you find that your fan and light kit go on and off without using your remote control, simply change the code combination in your transmitter and receiver.
   D. Operating the buttons on the panel of the transmitter.
   HI, key -for fan high speed.
   MID-key-for fan medium speed.
   LOW key-for fan low speed.
   FAN OFF key-for fan off.
   REV key-for fan REV speed.
   LIGHT/DIMMER key-for light brightness and off.

• The light function is controlled by pressing the LIGHT/DIMMER key down to increase or decrease light.
  Tap the key quickly to turn the light off or on.
  *Keep pressing the button in excess of 0.7 seconds and it becomes dimmer, the light varies cyclically in 0.8 seconds. The receiver can remember the last status of the light brightness when the light was switched so that it can resume adjusting the light brightness.|
  ---|---

“Optional Wall Mounting for Transmitter Holder” Place an inaccessible area of your home, and screw the transmitter holder into the wall using the two screws provided, slide the hand unit into the holder.

4. TROUBLESHOOTING GUIDE
   1. Fails to operate
   a. Power to receiver?
   b. Receiver wired correctly?
   c. Fan manual speed control in highest position?
   d. Light kit switch turned on?
   e. Good battery in the transmitter?
   f. Code set at exact same positions in both transmitter and receiver?
   2. Won’t operate at a distance
   If transmitter operates fan/light kit when up close, but not at 20 feet away.
   Try placing the brown antenna wire higher, up through the ceiling/outside the juston box.

NOTICE!
Your ceiling fan and light kit assembly must meet the following requirements:

1. Do not use with solid state fans.
2. Electrical rating: 120v 60Hz 3.5A
   MAX. Motor amps: 1.0
   MAX. Light watts: 180-(incandescent, or ballast non-dimmer, or LED)

WARNING
TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED WITH A WALL CONTROL/SWITCH.

size of product

TROUBLESHOOTING GUIDE

Please refer to the instruction sheet for detailed directions and descriptions of installation steps and requirements.

1. FAN/REMOTE IS NOT WORKING
   Ensure the remote is within the 20-foot range of the receiver
   To reset the remote control: 1) Turn off power to the fan using the wall switch or circuit breaker. 2) Remove batteries from the remote. 3) Wait 10 seconds. 4) Replace batteries and turn the power on.
   Check batteries to insure they are good and oriented correctly.
   Check to make sure the frequency switches (DIP Switches) from the remote to the receiver are set to the same frequency.
   Check the main and branch circuit fuses or breakers.
   If using a Variable Speed Wall Switch, ensure it is specifically designed for use with a ceiling fan.
   Check the line wire connections to the fan and the switch wire connections in the switch housing per the instructions.
   If the fan still does not work, please contact Customer Service Support@parrotuncle.com

2. THE FAN IS NOISY
   Make sure all motor housing screws are tightened.
   Make sure the screws that attach the fan blade to the motor are tight.
   Make sure the wire nut connectors are not rattling against each other or the interior wall of the switch housing.
   Allow a 24-hour break-in period. Most noises associated with the new fan may disappear during this time.
   If using a ceiling light kit, make sure the glassware is secured tightly
   Make sure there is a short distance/gap from the ceiling to the top of the canopy. The canopy should not touch the ceiling!
   Make sure your ceiling box is secure and that the rubber isolator pads are used between the mounting bracket and outlet box.

3. THE FAN WOBBLES
   Verify all blades and blade bracket screws are secure (most fan wobble problems are caused by loose parts). If one of the fan is properly installed, run the ceiling fan for 10 minutes to let the fan self-adjust.
   If wobble occurs after running the fan for 10 minutes, verify blade level using the following process:
   a) select a point on the ceiling above the tip of one of the blades. Then select the fan blade and measure from the center of the selected blade to point on the ceiling. Rotate the fan until the next blade is positioned and repeat the measurement using the same point from the ceiling for every blade. Measurements should be within 1/8 inch.
   b) If all deviations are less than 1/8 inch and the fan continues to wobble, please contact Customer Service Support@parrotuncle.com to order a complimentary Blade Balancing Kit
   – If all deviations are less than 1/8 inch and the fan continues to wobble, please contact Customer Service Support@parrotuncle.com to order a complimentary Blade Balancing Kit

4. THE LIGHT IS NOT WORKING
   Check Bulb to make sure it is installed correctly.
   Remove the non-working bulb and replace it with a bulb that is known to be a good working bulb
   To reset the remote control: 1) Turn off power to the fan using the wall switch or circuit breaker. 2) Remove batteries from the remote. 3) Wait 10 seconds. 4) Replace batteries and turn the power on.

AFTER INSTALLATION
WOBBLE”
The fan blades have been adjusted in the factory to minimize any wobble.
NOTE: CEILING FANS TEND TO MOVE DURING OPERATION DUE TO THE FACT THAT THEY ARE MOUNTED ON A RUBBER GROMMET. IF THE FAN IS MOUNTED RIGIDLY TO THE CEILING, IT WOULD CAUSE EXCESS VIBRATION. THE MOVEMENT OF A FEW CENTIMENTERS IS QUITE ACCEPTABLE AND DOES NOT SUGGEST ANY PROBLEM.
TO REDUCE THE FAN WOBBLE: PLEASE CHECK THAT ALL SCREWS WHICH SECURED THE MOUNTING BRACKET AND DOWNROD ARE SECURE.
BALANCING A WOBBLING CEILING FAN:
For your convenience, a Balancing Kit is included; please follow this procedure when balancing the fan:

1. Check that all blade and blade arm screws are secure.

2. Most fan wobbling problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the blades. Measure this distance. Rotate the fan until the next blade is positioned for measurement. Repeat for each blade. The distance deviation should be equal within
   1/8″(0.32cm).

3. Use the enclosed Blade Balancing Kit if the blade wobble is still noticeable.

4. If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight and possibly result in a smoother operation.
   WARNING: TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE ARM WHILE INSTALLING, BALANCING THE BLADES, OR CLEANING THE FAN. DO NOT INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.

NOISE
When it is quiet(especially at night) you may hear occasional small noises. This is normal. Please allow a 24-hour “breaking-in” period, most noises associated with a new fan disappear during that time.
CARE AND CLEANING

1. Periodic cleaning of your ceiling fan is the only maintenance required. Use a soft brush or lint-free cloth to avoid scratching the paint finish. Please make sure to turn off electrical power before you clean your fan
2. Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create the possibility of an electrical shock.
3. The motor has a permanently lubricated ball bearing. No need to oil

NOTE: MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BEFORE YOU ATTEMPT ANY CLEANING OR REPAIRS.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>