PYLE PL1SN104 10.1 Inch Touch Screen TFT or LCD Monitor Single Din MP5 Player User Manual

PyleUSA.com
User’s Manual

|
---|---

PL1SN104
Adjustable Viewing Angle (Maximum Angle 360°)

WARNING For your safety, the driver should not operate the controls while driving. Also, while driving, keep the volume to a level at which external sounds can be heard.

Precautions

1. When the interior of the car is extremely cold and the unit is used soon after switching on the heater, moisture may form on the disc or the optical parts of the player and proper playback may not be possible. If moisture forms on the disc, wipe it off with a soft cloth. If moisture forms on the optical parts of the player, do not use the player for about one hour. The condensation will disappear naturally allowing normal operation.
2. This unit uses precision parts and components for its operation. In the event that trouble arises, never open the case, disassemble the unit, or lubricate the rotating parts. Contact your service center.
3. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to protect reasonably against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio reception, which can be determined by turning the equipment off and on, the user is encouraged to consult an experienced radio technician for help.

Wiring-Back Panel:

Wiring-Color Wiring:

for an external amplifier
Orange| ILLUMINATION| 12 volt + trigger dashboard illumination
Brown W| BACK UP CAMERA| 12 volt + trigger from reverse lights
Pink| PARKING| Connect to parking brake ground. Disables video play unless grounded
Blue| AUTO ANTENNA| 12 volt + trigger output
Gray/White| SW-GROUND| Steering wheel control Key 2 interface wire
Black (RCA)| CAM VIDEO IN| Camera RCA video input for use with rearview camera
Red| ACC| Ignition Accessory 12V+
Yellow| FUSE/ POWER B+| Connect to (+) side of car battery
Black| GROUND| Connect to (-) side of car battery
Purple| Speaker Rear R| Rear right speaker         Purple (+) Purple/Black (-)
Green| Speaker Rear I,| Rear left speaker           Green (+) Green/Black (-)
Gray| Speaker Front R| Front right speaker       Gray (+) Gray/Black (-)
White| Speaker Front L| Front left speaker           White (+) White/Black (-)

*Brown wire tells the monitor when to activate and display the rearview camera on the display (optional)

General Operation:

Profile of main interface

1. Time Setting
2. Radio
3. Bluetooth
4. USB
5. SD Card
6. Navigation (optional)
7. Steering Wheel Control Setting
8. EQ
9. Wallpaper
10. AUX
11. AutoLink
12. Settings

Note: If there is no device connection, icons for USB, and SD will be shown no device. Click is invalid in this case. Display setting is invalid if there is no audio or video playing.
Radio

• Radio Region: Set the unit for one of the following regions: Europe, America, China, Russia,
  Japan, RDS (on/off)
  Multimedia player

• Support lots of video and audio formats

• Subwoofer: Tum the subwoofer output On or Off

• EQ-Sertting: Pop, Rock, Classical, Jazz, or Off
  Time

• Slide the figures in the set time interface
  Language

• Language: Select desired language(English, Spanish, Deutsch, Russian, Portuguese, French, Chinese, etc.
  Camera input

• Connect the camera with this device, and can auto-detect the brake signal when reversing.
  (Note: Camera is not included)
  Car logo

• Preset car logo to match your car brand
  Steering wheel control

• Set the function button on your steering wheel via the system learning setting
  AUX Input

• Connect an optional audio video source to the Aux input
  AM/FM Tuner Operation
  Radio interface RDS turn on function
  Touch Radio icon in main interface to switch to radio mode.

| Short press this button to downward search the station semi-automatically
---|---
| Short press this button to upward search the station semi-automatically
| Switch the receiving band
| Scan
| EQ
| Locate / remote channel
| Single track, In FM band, press this button to switch between ST and MONO, The default setting is ST. AM band doesn”t have this function

Multimedia player

• Support MP3.WMA.AVI,MOV,MP4,RMVB,VOB,FLV,etc media format

• Support SD, USB, MMC

• Support JPEG, BMP, PNG, etc. picture format
  Music interface

• The system will automatically read USB and SD.

• The user can directly click options in the directory menu to perform the play.

1. Click the icon to enter the playlist

| EQ
---|---
⏮️| Select Previous Program / Title / Song
| Play / Pause
| Select Next Program / Title / Song
| Volume
| Title Menu
| Selection

Video or Picture playing interface

Note: Sliding the controlling bar at the bottom to show the next page.
AUX in (Auxiliary device input)
Click in from the main interface SRC key in the remote control to switch to AUX in Mode. AUX in enables external media sources to connect to the system, like camera, video games, Walkman, external navigation box (controlled by the remote controller), etc. No auxiliary device input shows at the below picture. Connect external devices through the 3.5mm auxiliary audio/video input. It can display the corresponding picture as the output video.

Rearview Camera
Auto operation: After connecting with the reverse camera, it will automatically detect the reverse signal and show the reverse pictures. The system will swift to any mode to rear view lens mode automatically. When reverse is over, the system will come back to the previous mode.

Wireless BT Streaming

| Dialing
---|---
| Call records
| Phone book
| Bluetooth music
| EQ
| Settings

Wireless BT Music
The phone must support A2DP agreement. Press BT Music icon in the main interface. Under the connected mode, click the play keys in the Wireless BT interface to play different music formats restored in the phone. Due to different types of phones, music can be played either by choosing music player on the phone or click the play key in the Wireless BT interface.

Settings| Default| Options|

Function

---|---|---|---
BT| On| | BT is in standby when the device is turned on
Device| Not Paired| Device Name| When connected, the current Wireless BT device name will be displayed. Press the device name to display a list of available devices that can be connected.
Connect| Auto| | After connecting with the same device one time, it will be auto-connected next time.
Auto Answer| Manual| Manual| You must press the Talk button to answer an incoming call
Auto| All incoming calls will be automatically answered

Notes: Some Bluetooth approved devices may not communicate or work properly with this head unit, depending on the features or specifications of the device. During hands-free operation, some noise may be heard when using a mobile device with this head unit, depending on the mobile device and or the communication environment.

AutoLink Software(Phone Link)

AutoLink connects your device to your Android mobile phone and iPhone through the standard USB port and transfers the picture and sound from the phone to the device. You can control the phone through the device’s screen, such as receiving calls, dialing calls, listening to music, and watching movies, or photos.
Connect your ANDROID phone or iPhone to the unit with an original USB cable, touch the AutoLink icon, open the menu, then follow the instructions.

|
---|---

Enable USB debugging
Before connecting AutoLink to an Android mobile phone, ensure that the ‘USB Debugging’ option of the Android mobile phone has been enabled. The method for enabling ‘USB Debugging switching’ will be different for different versions of the Android system. Pls select the connection wizard according to the system version of the mobile phone to operate on the phone in a sequence.

1. Select ‘Developer Options’, click ‘Additional Settings’, run ‘Developer Options’, click to Open USB debugging.
   

2. Select Phone settings, click ‘About phone’, click ‘The number of System version’ or ‘Build number’ for several times, click ‘Developer Options’, and enable USB Debugging.

Note: If the connection fails, check the USB cable connection or restart the ANDROID mobile and check the procedure. When the phone link icon is clicked correctly, the phone screen will be displayed on the device screen.
Depending on the type of phone, there may be a difference in the AutoLink
Not all phone models are compatible with the AutoLink feature.

Setting

Note: Sliding the bar on the left side to see more optional settings.

Wheel Set Setting

Connect the steering wheel control cable, and click the corresponding key to activate the function. After entering into the steering wheel control interface, then keep pressing
the steering wheel “VOL+” button in your car, at the same time click “ ”in the interface, it will be selected, then it is finished this setting. Click other buttons according to this method, the steering wheel function can be used.

Troubleshooting

Phenomenon| Reasons|

Solutions

---|---|---
Normal| |

Not operating

| A fuse of machine power supply and auto vehicle battery is burnt, Voltage of power supply is overloaded Automatic protection system avoids fault due to illegal operation Wrong pin assignment ISO connector| Change for the fuse of the correct types;
Adjust voltage; Reset the system by pressing the Resetkey Check the wiring diagram
Remote control does’ t work| Battery is out of power; Battery is not placed correctly| Change new battery; Reinstall battery

**** No or low sound

| Disconnection; Volume setting is low volume; wrong connection of Silence; Loudspeaker fault; Volume balance setting bias Earthing in loudspeaker connection| Check the connection; Increase the volume; Reconnection the silence wire complied with the installation instruction; Change for a new loudspeaker; Adjust the volume balance setting to the middle place; Keep the insulation of the loudspeaker connection
Inferior quality of sound; Distortion of sound| Inferior disc is used; Loudspeaker does not match the impedance of the machine; Loudspeaker opens the circuit.| Use genuine discs; Change a loudspeaker; Check the connection of the loudspeaker.
Machine reset by itself when it is shut down| Connection of ACC and B+ is not correct.| Check and reconnect ACC and B+
Turnover screen| |
---|---|---
Turnover screen does not open automatically.| Auto Open of turnover screen setting is OFF.| Auto Open» ON
No image| Connection of the brake wire is not correct; Not brake state| Connect brake wire with the cathode of power supply correctly; Keep brake state after a car is placed safely.
Unstable output of images| DVD does not correspond with the present system video setting; the Video signal line is not connected correctly.| Adjust the system video setting; Check and make sure of the connectivity. Unsupported code
Images being stretched or compression| Inappropriate image proportion setting| ** Adjust image setting
Trouble| Cause(s)| Solution (s)
---|---|---
Radio| |
** Weak signal| Auto antenna does not reach out completely LOG function is under working state| Connect auto antenna line correctly; Close LOC function.
Disc/Card Reading| |
Break-down during playing| Disc is stained or scratched; Documents or records are damaged| Clean or replace the disk; Replace the disk or choose the stored file
The wrong information is shown on the panel| The screen cannot display all the information.|

Error or not operating| Illegal operation| Hold the EJECT key for 5 seconds to reread the device. Take out the disk inside the machine
Disc cannot enter| There is a disc already on the side of the device. The disc is not fully accepted.| and replace a new disc Transport the screws
the device Disc does not play| The disk level surpasser the level setting of the Lock function; The area code of the disc is not compatible; the Disc is turned upside down.| Adjust the level setting of the Lock feature; Use a compatible disk; Keep the side with sign up when inserting the disk.
SD card readable by PC but unreadable by the device| Due to compatibility reasons of SD card brands, not all of the SD cards can be read under the system. Or you may wrongly use an MMC card as an SD card.| The present system mainly supports the following SD card brands: San Dick, KingMAX, Kingston, Panasonic, Apacer, etc.
Nonrepeat and search function while play VCD| PBC service is functioning| Shut down PBC service

Systematic Parameter

Specifications

• Working voltage: Direct current 12V
• Working voltage range: 10.8V-16V
• Maximum working electronic current: 10A
• Installation angle: less than 30 degree tilted on the front side and backside

Device
USB/SD| Type(•*)
• MP3
• WMA
• JPEG (1080×920)
• AVI
• RMVB
• MPG
• DAT
---|---

• Power output: 4X80 W
• Impedance 4ohm
• SNR: 70dBA
• Frequency Response: 20Hz-20kHz

Video

• Standards: NTSC. PAL (Auto-recognition)
• Output: 1 Vp-p (75ohm)
• Input: 1Vp-p (75ohm)

Features:

• Single Din Size Universal Standard
• Hi-Res 10.1” Digital Display
• Full HD 1080 Support
• USB Flash Drive Reader
• AM/FM Radio with 30 Station Memory
• Video Aux (RCA) Input/Output Connector Jacks
• Rearview Backup Camera Support
• Audio Aux (RCA) Input/Output Connector Jacks
• Marine Grade Waterproof Construction
• Night Vision Illumination
• Total Pixels: 656 x 492
• 170 Degree Wide Viewing Angle
• 420 TVL Horizontal Resolution

FM Radio

• Frequency modulation:
  87.5 MHz ~108.0MHz (Europe)

• Flexibility (-30dB):10dBu
  SNR (-50dB):15dBu

• Frequent sound range: 30H2~15kHz (+3dB)

AM Radio

• Frequency range:
  522KHZ-1620KHZ (Europe)

• Sensitivity (SN=20dB): 20dBu

• Image rejection: 60dB

• Frequency response: 50HZ-2KHZ (+-3dB)

Display

• Screen type: TFT
• Response time: up=30 millisecond.
• Down=50 millisecond
• Angle range: depression angle=65°
• elevation angle=40<>
• Left vision=65 Right vision=65

Environment temperature

• Operation temperature:
  -4°F~158°F or -20~+70°C
• Maintenance temperature:
  -22°F~176°F or -30°C~80°C
• Operating humidity: 45%~+80%°C (relative humidity)
• Maintenance humidity: 30%~90% (relative humidity)

Disassembly Steps of Display

1. Pull the two clips(A&B) on the back of the display to both sides.
   

2. Remove the display.
   

3. Press the clips toward the center and unplug the cable.
   

4. Disassembly completed.
   

Rear View Backup Camera Installation

Please read all of the installation instructions carefully before installing the product. Improper installation will void the manufacturer’s warranty. The installation instructions do not apply to all types of vehicles and are written as guidelines to assist in installing the system. Please consult an experienced technician if you are not comfortable installing the product. Prior to using and installing the Backup Camera System, please read the safety information provided in this user manual. Be sure to use the product as outlined in this user manual. Alteration or modifications carried out without appropriate authorization may invalidate the user’s right to operate the equipment.

WARNING: Failure to read and follow these warnings and instructions may result in serious injury, including damaged property, so please pay close attention and exhibit the utmost care.

• The Digital Backup Camera is designed as an aid to the driver in detecting potentially hazardous driving conditions, obstructions, and large stationary objects. You, the driver, must also remember to drive safely and properly. The use of the Digital Backup Camera is not a substitute for safe, proper, and legal driving practices.

• Never back up while looking only at your connected monitor display screen. You should always check behind and around the vehicle when backing up just as you would if the vehicle did not have the Digital Backup Camera. Always make sure your driving area is clear. Always back up slowly and with caution.

• Never depend on the Backup Camera entirely when backing up. The image on the monitor display screen may be slightly different from actual and real-time conditions. Objects viewed in the rearview monitor differ from actual distances because a wide-angle lens is used. So use the camera as an aid and always follow the intended driving
  practices to properly judge distances from objects.

• The Backup Camera’s assisted low lux lighting performance feature is also an aid to a driver. Always use your own eyes to confirm the vehicle’s surroundings, as the displayed image may be not well lit or not entirely visible. Always proceed with caution and perform double-checks before proceeding.

• The area displayed by the Backup Camera is limited. It does not display objects that are close to or just below the bumper, underneath the vehicle or objects out of the camera’s view. The camera’s view can change according to your vehicle’s orientation on the road or changing road conditions.

• Be sure to check the camera is properly functioning, is properly positioned, and securely mounted, every time you operate your vehicle.

• Make sure your trunk or hatch operates correctly, as intended, before and after installation.

• Proceed with caution when cleaning your vehicle around the camera. Avoid excess water exposure around the camera, especially with spraying or a power washer.

• Please make sure to keep the camera clean and unobstructed from any debris

• Follow all traffic laws and motor vehicle regulations.

• Consult local laws and regulations for any restrictions on installation or use.

• Using a Backup Camera System is not adequate enough to completely eliminate a vehicle’s blind spot. Always remember to drive with caution, following all traffic laws.

System Installation and Wiring

Note: Camera System installation on diesel vehicles may require a slightly different wiring install. Caution: Connecting to other types of electrical systems will cause damage to your vehicle. Please contact the manufacturer if you are unaware of the system type in your vehicle. Refer to the model’s power requirements prior to connection and installation.
QUICK INSTALLATION:
This rearview backup camera system comes with a camera and installation wiring. When installing, the camera is preferable to be mounted in the rear of your vehicle (just above the license plate).
This kit includes necessary wiring and cable connector accessories sufficient for typical connections. However, additional accessory cables and installation materials may be necessary for completely secure and operational backup camera performance.
Camera Connection:
Connect the camera to the using the included DC 12V power cable. Connect the DC 12V power cable to the positive 12V reverse tail light in the rear of your vehicle. Then, connect the black wire, of the DC 12V power cable, and ground it properly. This connected power and ground cable then connects to the camera and will supply power to the camera directly.
Next, use the included yellow RCA video connector cable, and run that cable from the yellow RCA video connector jack of the camera to the yellow video connector of your compatible display monitor. The yellow RCA cable when connected automatically retrieves the video signal when activated (when your vehicle is switched into the reverse gear).

Installation Transcript:

1. Locate the reverse taillight wiring behind your vehicle’s reverse light. You may need to remove an interior panel, or another cover, in order to locate the wiring. Connect the included power 12V DC power cable to the reverse light.
   a. Connect the power cable’s Red wire to your vehicle’s reverse light positive wire.
   b. Connect the power cable’s Black wire to your vehicle’s reverse light negative wire.

2. Connect the camera to this ‘reverse light’ connection installation, then mount the camera in the desired location.

3. Run the RCA video cable from the camera to your compatible video display monitor.

• Please remember to run cables in the least obtrusive route possible. Vehicle vibrations and bumpy driving conditions can result, so extra care should be taken to securely mount the camera and fasten all cables and wiring to secure locations.
• Ensure the wires are safely and securely connected, with proper isolation applied to all connections.
  Additional Notes:
  • Determine the best location for the camera (The camera is preferably mounted just above the license plate).
  • Be sure when running the connection cables to leave a small amount of slack so you can still move the camera around the license plate if you decide to slightly adjust the camera’s positioning at a later time.
  • After installation, test the camera before use. Placing your vehicle in reverse should provide a picture in the monitor within the rearview mirror assembly.

Angle Adjustable Camera Lens

• Located on the camera housing are 2 screws that lock the camera lens angle in position.
• The screws may be loosened to allow camera lens angle adjustment
• Loosen the screws, and adjust the camera lens to the desired angle. then tighten the screws securely.
• Be sure as to not overtighten the screws.

Questions? Issues?
We are here to help!
Phone: (1) 718-535-1800
Email: support@pyleusa.com

PyleUSA.com

| VISIT US ONLINE:
Have a question?
Need service or repair?
Want to leave a comment?
PyIeUSA.com/ContactUs
---|---

www.PyleUSA.com

Documents / Resources

| PYLE PL1SN104 10.1 Inch Touch Screen TFT or LCD Monitor Single Din MP5 Player [pdf] User Manual
PL1SN104, 10.1 Inch Touch Screen TFT or LCD Monitor Single Din MP5 Player, PL1SN104 10.1 Inch Touch Screen TFT or LCD Monitor Single Din MP5 Player
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>