BFL-4(4/1) Butterfly Wheelchair Accessible Table Installation Guide

BFL-4(4/1) Butterfly Wheelchair Accessible Table

PARTS DESCRIPTION

CONTACT TECHNICAL SUPPORT AT 1-888-678-2060.**
---|---

BASE ASSEMBLY

STEP 1

1. BEFORE STARTING ASSEMBLY, PLEASE REMOVE TABLE ARMS (#6) FROM BASE A (#1) & BASE B (#2).
2. IN ORDER FOR THE BFL-4(4/1) TO BE TRANSPORTED PROPERLY AND SAFELY, PLEASE MAKE SURE BOTH TRANSPORT CASTERS (#13) ARE POINTING IN THE SAME DIRECTION.

STEP 2

Required Items:
Base A (#1)
Base B (#2)
1/2” Screw (#4) X4

• Place Base A (#1) onto a flat surface. Position Base B (#2) at 90 degrees to Base A (#1). Push Base B (#2) down onto Base A (#1) until the tops of the center post are flush.
  Use 1/2 Screws (#4) to secure bases (Do not over tighten).

| IN ORDER FOR THE BFL-4(4/1) TO BE MOVED PROPERLY AND SAFELY, PLEASE MAKE SURE BOTH TRANSPORT CASTERS (#13) ARE POINTING IN THE SAME DIRECTION BEFORE PROCEEDING. IF NECESSARY, PLEASE SEE STEP 1.
---|---

BASE PLATE ASSEMBLY

Required Items:
Leg Attachment Plate (#3)
1/2” Screw (#4) X12

• Tip the entire assembly over (legs in air). Secure Bases together by bolting the Attachment Plate to the underside of Base A (16 screws). Tighten screws securely.

Required Items:
Pneumatic Pistons (#5) X4

Pneumatic Pistons: Place the end with the spring into the PVC tube before inserting into frame.

• Tip the frame, placing it on its legs. Place Pneumatic Pistons (#5) into frame tubes. These pistons are helpful when adjusting the height of each table top.

TABLE TOP / MOUNTING BRACKET ASSEMBLY

Required Items:
Table Tops (#10) X4
Table Top Mounting Brackets (#11) X4
M6x16 Mounting Bracket Screws (#12) X32

• Lay Table Top (#10) on a level floor with pre-drilled holes pointing up. Using the Allen Wrench provided, secure Table Top Mounting Bracket (#11) using the M6x16 Mounting Bracket Screws (#12). Repeat on all Table Tops (#10).
  

TABLE TOP ASSEMBLY

Required Items:
Table Arms (#6) X4
Adjustable Knobs (#7) X4
1 1/4” Bolts (#8) X8
1/4” Nuts (#9) X8
Table Tops (#10) X4

• Insert Table Arms (#6) into the assembled base. Ensure the “L” shaped bracket is held to one side while inserting the arm tops into the center post.

• Insert 1 1/4” Bolts (#8) into Table Arm (#6) and tighten with 1/4“ Nut (#9).
  Start with inner pre-drilled hole – this is to stop the Table Tops from hitting the arm. Repeat on all four Table Arms.

• Slide Table Tops (#10) onto Table Arms – See Diagram B. Use Adjustable Knobs (#7) to secure tops.

• Insert 1 1/4” Bolts (#8) into outer pre-drilled hole of Table Arm (#6). Tighten with 1/4” Nut (#9) – this is to stop the Table Tops from sliding off the arm.

FINAL ADJUSTMENTS

• Use Adjustment Knobs (#7) to secure the table tops at the desired height.
• Operation: Two offset casters have been provided to ensure easy & safe relocation of the table. To move the table, lift the table from opposite side of the casters by 10” off the floor. Adjust glides to level & stabilize the table. Secure by tighten the locking nut.

BFL-4(4/1) SPECIFICATIONS

OVERALL: 48” X 48” (EXTENDED – 58” X 58”)
INDIVIDUAL TOP: 26”W X 22”D
HEIGHT ADJUSTMENT: 26” – 36”
20” – 30” – OPTIONAL

ADDITIONAL MODELS:

Documents / Resources

| Butterfly BFL-4(4/1) Butterfly Wheelchair Accessible Table [pdf] Installation Guide
BFL-4, Wheelchair Accessible Table, Accessible Table, Table
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>