SmartPet RS1 Dog Training Collar User Guide

DOG TRAINING COLLAR

Model: RS1

Quick Start Guide

Charge the Receiver and the Remote Transmitter for 3 hours with the cable in the package box. Micro-USB is used to charge the Remote Transmitter, and 5.50C Is used to charge the Receiver.
Make your dog sit down and fit the Receiver to your dog by leaving one finger space between the collar and your dog’s neck, Center the contact points underneath your dog’s neck, touching the skin.

Turn on the Receiver by pressing and holding the Power Button for 2 seconds with vibration to indicate that the Receiver Is powered on.

Turn on the Remote by pressing and holding On/Off(Channel) Button for 2 seconds.

Warning Tone Command: press the Warning Tone Button, and the green indicator lights rapidly flow from both ends and meet in the middle, and the Receiver will deliver a warning tone. Press the Level Button to adjust the warning tone levels. vibration Command: press the Vibration Button, and the yellow Indicator lights rapidly flow from both ends and meet In the middle, and the Receiver will deliver the vibration. Press the Level Button to adjust the vibration levels.

Shock Command: press the Shock Button, and the red Indicator lights rapidly flow from both ends and meet In the middle, and the Recelver will deliver the static shock. Press the Level Button to adjust the shock levels.

Switch the channel by pressing the On/Off(Channel) Button. This product can train up to 2 dogs.

Pair the Remote Transmitter to an extra Receiver: first, change the channel of the Remote Transmitter to Channel 2 by pressing the On/Off (Channel) Button, next press the Power Button on the Receiver 3 times until you hear a beeping. Then press any one of the Warming Tone, Vibration or Shock Button, and the Receiver will respond respectively.

**Important Safety Information:

**

WARNING
Not for use with aggressive dogs. Do not use this product if your dog Is aggressive, or if your dog Is prone to be aggressive Aggressive dogs can cause severe injury and even  eath to their owner and others. If you are unsure whether this product Is  appropriate for your dog, please consult your veterinarian or a certified trainer.

• For use with dogs over 6 months of age.
• DO NOT use It when the dog or the collar Is wet.
• DO NOT press and hold shock or vibrate for more than 10 seconds to avold physical or psychological damage to your dog.
• Your dog should not vocalize or panic when receiving stimulation. If this happens, the stimulation level is too high and you need to go back tc the previous level and repeat the process.
• DO NOT charge the device near any flammable substances.
• Dog use only. Not for use on children.
• This is not a toy, and should only be operated by a responsible adult.

CAUTION
For on-leash training. Do not attach the leash to training collar.
Use a regular collar In addition to the training collar.
Risk of skin damage. Please read and follow the instructions in this manual. Proper fit of the collar is Important. A collar worn for too long or made too tight on the dog’s neck may cause skin damage. Ranging from redness to pressure ulcers; this condition is commonly known as bed sores.

• DO NOT leave the collar on the dog for more than 12 hours per day.
• When possible reposition the collar on the dog’s neck every 1 to 2 hours.
• Check the fit to prevent excessive pressure; follow the Instructions In this manual.
• Never connect a lead to the collar; It will cause excessive pressure on the contacts.
• Wash the dog’s neck area and the contact probes of the collar weekly with a damp cloth.
• Examine the contact area dally for signs of a rash or a sore.
• If a rash or sore !s found, discontinue use of the collar until the skin has healed. If the condition persists beyond 48 hours, see your veterinarian.
• The Receiver collar meets IP67 waterproof rating, It can be submerged Into water up to 1 meter for up to 30 minutes. If submerged and wet, please do not use it.
• This product comes with conductive silicone covers, please ensure they are worn on the contact points before putting the Receiver on your dog and check for the presence of the silicone cover every hour.

How the System Warks
The Remote Training Collar Is easy to use with an advanced digital display that tells you exactly what level of stimulation you are using.
The Remote Training Collar assists you in controlling your dog without a leash.
At the push of a button, your Remote Transmitter sends a signal activating your dog’s Receiver. He receives a safe but annoying stimulation. He’ll quickly learn the association between his behavior and your correction; in no time, you’ll have a better-behaved dog. The Remote Training Collar has been proven safe, comfortable, and effective for both small and large dog breeds.
Using the Remote Training Collar consistently and correctly, any basic obedience commands can be taught and will help to correct many misbehaviors that your dog exhibits.

Remote Transmitter

Package Content

Product Overview

Receiver

|
---|---

Setting UP

charging the Product
Remote Transmitter: charge the device until the Colorful Indicator Light becomes solid green which will take around 2-3 hours. Receiver: charge the device until the Indicator becomes solid green which will take around 2-3 hours.

Warning: Please use a charger with a 5V output voltage that can always be seen onthe surface of it. If charged with a charger with an output voltage over 5V, the Receiver will deliver a rapid warning tone and stop charging automatically, and the Remote Transmitter will stop charging automatically with the colorful indicator rapidly blinking in red.

2. Turn on/off the Product
Turn on the Remote Transmitter by pressing and holding the On/Off (Channel) Button for 2 seconds, the red, green and blue indicator lights successively flow from left to right, which means the Remote Transmitter is powered on.

Turn off the Remote Transmitter by pressing and holding the On/Off (Channel) Button for 2 seconds, the blue indicator lights quickly flow from the middle to both ends, which means the Remote Is powered off. Turn on the Receiver by pressing and holding the Power Button for 2 seconds.![SmartPet RS1 Dog Training Collar

• fig 16](https://manuals.plus/wp-content/uploads/2022/07/SmartPet-RS1-Dog- Training-Collar-fig-16.png)

Training Modes

1. Warning Tone Mode
   When pressing the Warning Tone Button, the green Indicator lights rapidly flow from both ends and meet in the middle, and the Receiver will deliver a warning tone. It will cut off automatically if you press and hold the Warning Tone Button for 10 seconds. There is a total of 8 levels of Warning Tones for training which you can adjust by the
   Adjustment Button.

2. 

3. Vlbration Mode
   When pressing the Vibration Button, the yellow Indicator lights rapidly flow from both ends and meet In the middle, and the Recelver will deliver a vibration. it will cut off automatically If you press and hold the Vibration Button for 10 seconds. There Is a total of 16 levels of Vibration for training which you can adjust by the Adjustment Button.
   

4. Shock Mode
   When pressing the Shock Button, the red indicator lights rapidly flow from both ends and meet in the middle, and the Receiver will deliver a static shock. It will cut off automatically if you press and hold the Shock Button for 10 seconds. There is a total of 99 levels of Shock for training which you can adjust by the Adjustment Button.
   

5. Switching Channels
   Press the Channel Button to choose the Receiver you want to control If you have paired up two Receivers.

Fitting the Receiver

Important: The proper fit and placement of your Receiver are important for effective training. The Contact Points with Conductive Silicone Cover must have direct contact with your dog’s skin on the underside of his neck. To assure a proper fit, please follow these steps:

1. Make sure that the Receiver Is turned off.

2. Have your dog standing comfortably (A).

3. Place the Recelver on your dog’s neck close to the ears. Center the Contact Points underneath your dog’s neck, touching the skin. Note: It is sometimes necessary to trim the hair around the Contact Points to make sure that contact is consistent.

4. The Receiver should fit snugly, yet loose enough to allow one finger to fit between the strap and your dog’s neck (C).

5. Allow your dog to wear the collar for several minutes then recheck the fit. Check the fit again as your dog becomes more comfortable with the Receiver.
   

6. How to attach the collar to the Receiver ?
   Follow the following 1-2-3-4 steps instructed to the strap.

CAUTION: Risk of Skin Damage. Too long time or too tightly fitting may cause pressure necroses, which if often misidentified as burns. Please follow the below instructions:
-Do not shave the dog’s neck as this may Increase the risk of skin irritation.
-Do not leave the Receiver on your dog’s neck for continuous 12 hours.
-Never attach a leash to the collar.
-Never fit the Receiver too tight to your dog’s neck.

Pairing Up

If you feel the Receiver is not responding to the Remote Transmitter, follow these steps to pair them up.

1. Press and hold the Power Button on the Receiver for 2 seconds and the On/Off (Channel) Button to turn both of the Receiver and the Remote Transmitter on.
   

2. Prass the Power Button on the Receiver 3 times to enter the Pairing Mode. You will hear beeping and the Indicator become solid. You will now have 10 seconds to finish the pairing.

3. Press the Warning Tone Button, Vibration Button, or Shock Button on the Remote Transmitter, and the Receiver will respond correspondingly indicating that the Pairing process is completed.

Tips:
The Receiver is paired up to Remote Transmitter in Channel 1 by factory default setting.
If you buy a new Receiver, you follow the above palring Instruction to pair up to channel 2. The system can pair up to 2 Receivers in
2 different channels.
If you can not pair the device successfully, it may be caused by signal Interference. Please try in a new place or contact with our service center.
LCD Display & Indicator Definitions
Remote:

| Warning Tone Mode
---|---
| Vibration Mode
| Shock Mode

12

|  Channel 1 and 2
|  Levels for Warning Tone/Vibration/Shock
| Battery indicator

88

|

Remote colorful indicator light:

to right
Turn off| Blue light flowing
Press| Green light flowing
Press| Yellow light flowing
Press| Red light flowing
| Slowly blinking indicates the Receiver is on
Fast blinking indicates when the Receiver is on charge
Faster blinking indicates the Receiver battery is low

Traning Tip
How to find the best stlmulation for your dog?
Important: Always start at the lowest level and work your way up. The Remote Training Collar has 8 types of Warning Tones, 16 levels for Vibration and 18 levels for Static Shock. For Warning Tone, there are & types of tones and there is only a frequency difference among different types. For Vibration and Static Shock, level 1Is the lowest; level 16 is the highest for Vibration and 99 for Static shock. This allows you to choose the Stimulation level that is best for your dog. Once you have placed the Recelver on your dog, It Is time to find the Stimulation Level that Is best for him. This Is called the Recognition Level.
A slight change in your dog’s behavior, such as looking around in curiosity, scratching at his collar, or flicking his ears, indicates the Recognition Level that Is best for your dog.

Flolow the steps below to find your dog’s Recognition level:

1. Starting at Level 1, press the Warning Tone/Vibration/Shock Button continuously for 1 to 2 seconds.
   Note: When the Warning Tone/Vibration/Shock Button Is held down for 10 consecutive seconds, the Remote Transmitter will “time out”, and you must release and press the button again before additional stimulation can be delivered.

2. If your dog shows no reaction, repeat the Stimulation Level several times before moving up to the next level.

3. YOUR DOG SHOULD NOT VOCALIZE OR PANIC WHEN RECEIVING STIMULATION. IF THIS HAPPENS, THE STIMULATION LEVEL IS TOO HIGH AND YOU NEED TO GO BACK TO THE PREVIOUS LEVEL AND REPEAT THE PROCESS.

4. Move up through the Stimulation Levels until your dog reliably responds to the stimulation.

5. If your dog continues to show no response at the highest level of Vibration or Static Shock, check the fit of the Receiver. If your dog has long or thick hair, contact our Customer Care Center to obtain a longer set of Contact Points. Then go back to #1 and repeat the process.

If this still does not yield any results, your dog’s hair will need to be trimmed around the Contact Points. If after completing all of these steps, your dog still does not indicate he is feeling the stimulation, please contact our customer service.

HOW TO Maximize the distance ?
Terrain, weather, vegetation, transmission from other radio devices, and other factors will affect the maximum range.
Hold the Remote Transmitter in a horizontal position away from your body to achieve optimum range. For maximum signal strength, keep the device properly charged. *Avoid touching the antenna or the range may decrease substantially.

Frequently Asked Questions

Q: Is the Stimulation safe for my dog?
A; While the Stimulation is unpleasant, it is harmless to your dog.
Electronic training devices require interaction and training from the owner to achieve desired results.
Q: How old does my dog have to be before using the Remote Training Collar?
A: Your dog should be able to recognize basic obedience commands such as “SIt” or “Stay”. Dogs should be at least 6 months old before using the Trainer.
Q: Once my dog Is trained and has been obeying my commands, will he have to continue to wear the Receiver?
A: Probably not. You may need to reinforce training with the  Receiver from time to time.
Q@:ls the Receiver waterproof?
A:Yes. The Receiver meets IP67 waterproof rating, but make sure to keep the area dry when charging. Note: the Remote Transmitter Is not waterproof.
Q: Will get a maximum range with the Remote Training Collar?
A: The range of the Remote Training Collar will vary according to terrain, weather, vegetation, as well as transmission from other radio devices. See “How the System Works” for tips on maximizing your range.
Q: How long can I continuously deliver stimulation to my dog?
A:The maximum amount of time you can press the Warning Tone/Vibration/Shock button and deliver stimulation to your dog continuously Is 10 seconds. After this, the Remote Transmitter will time out, and these stimulation buttons must be released and pressed again.

Trouble Shooting

1. My dog does not respond whenl press 4 buttons.

• Make sure the Receiver has been turned on.
• If your range has reduced from the first time you used the Remote Training Collar, the battery may be low In either the Remote Transmitter or the Receiver.
• Many factors can impact the amount of range you have with the Remote Trainer. For a list of these factors, see “How the System Works”. ‘Test the Receiver. See “How to test the functions” for details. ‘Increase the Stimulation Level. Refer to “How to Find the Best Warning Tone/Vibration/Static Shock Level for Your dag’ for more information.
• Make sure the Receiver’s Contact Points are placed snugly against your dog‘s skin. Refer to “How to Fit the Receiver’ for more Information.

2. The Receiver will not turn on.

• Make sure the Receiver has been charged. For the Initial charge, be sure to charge It for4 hours. Subsequent charges only take 2~ 3 hours.

3. The Receiver is not responding to the Remote Transmitter.

• Verify the Receiver is on.
• ‘If the indicator is blinking rapidly, fully charge the Receiver.
• ‘If the first 2 solutions did not resolve your problems, please check the “How to pair the Remote Transmitter & Receiver” section.

FCC Statement

USA
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed communications. radio frequency energy and, If not Installed and used In accordance with the Instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur ina particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‘

• Reorient or relocate the receiving antenna.
• ‘Increase the separation between the equipment and receiver.
• ‘Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• ‘Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirements.

The device can be used in portable exposure conditions without restriction. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>