DS18 NXL-10 MARINE GRADE COAXIAL SPEAKER Owner’s Manual
- June 5, 2024
- DS18
Table of Contents
DS18 NXL-10 MARINE GRADE COAXIAL SPEAKER
FEATURES
- 10″ 2-Way Speaker for Marine & Motorsports.
- Continuous Power Handling 200W RMS Each.
- Peak Music Power 600W MAX Each.
- Sensitivity: 94.3dB at 1W/1M.
- Nominal Impedance: 4 Ohm.
- Frequency Response: 35Hz – 20KHz
- IP65 Marine Grade Compliant Specifications, 100% UV Stable.
- Sold as Pair.
COMPONENTS
- Coaxial Separate with Floating Design.
- Motor Structure Use Y35 Ferrite Main Magnet and Reverse N35 (Neodymium) Magnet.
- 25mm PEN Dome Tweeter.
- Copper ring utilized in motor structure for far field performance.
- lntegrated LED-RGB Lighting.
MATERIALS
- Injected Molded Polypropylene Cone with UV Protection.
- Soft PC Damping Glued Surround.
- PC injection Molded Composite Basket with UV Coating.
BT Control Module & App (LED-BTC) For Multi-Function for RGB LED Lighting (sold separately).
PACKING INCLUDES
- 2 x 10″ 2-Way Full Range Speaker For All Elements Marine (1 per box) .
- 2 x 1.5M #18 Speaker Input Wired With Fast Terminal.
- 2 x 1.5M #22 RGB Power Input Wired With Fast Terminal.
- 12xM4 Phillips lnner Hex Head 304 Stainless Steel (4mm Hex Tool).
READ BEFORE INSTALLATION
- Be sure to carefully read and understand the instructions before attempting to install these speakers.
- For safety, disconnect the negative battery terminal from the battery prior to beginning the installation.
- For easier assembly, we suggest you run all wires prior to mounting speakers in place.
- Use high quality connectors for a reliable installation and to minimize signal or power loss.
- Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle. If installation in a boat, take care not to cut or drill through the main hull.
- Never run wires underneath the vehicle. Running the wires inside the vehicle or hull area provides the best protection.
- Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the firewall.
INSTALLATION
- Determine where the speakers will be mounted. Ensure an area large enough for the speaker to mount evenly. Be sure that the mounting location is deep enough for the speaker to fit: only mount to a flat surface. Use extra caution when mounting on panels with urethane foam.
- Refer to the specification chart to determine the proper diameter hole to cut for the speaker.
- Mark the locations for the mounting screws. Drill the holes with a 0.75″ bit.
- Feed the speaker wires through the cutout and connect to the speaker terminals. Be sure to observe proper polarity when connecting the wires. The speaker’s positive terminal is indicated with a “+”.
- Fit the speaker and mount into place using six (6) screws.
- Tighten the screws until the speaker is snug in place.
- LED CONNECTIONS – There are two options to choose from:
WIRING
-
lf you have an LED Control Module (LED-BTC), Connect as shown in the Following diagram:
2. To connect without LED Control Module (LED-BTC), Connect as Shown in the Following Diagram: -
Green Color: “G” Fast Terminal Connect to Battery Negative.
-
Red Color: “R’ Fast Terminal Connect to Battery Negative..
-
Blue Color: “B” Fast Terminal Connect to Battery Negative.
-
Purple Color: “R” And “B” Fast Terminal Connect to Battery Negative.
-
Yellow Color: “R’ And “G’ Fast Terminal Connect to Battery Negative.
-
Cyan Color: “B” And “G” Fast Terminal Connect to Battery Negative.
-
While Color:”R’ And ‘B’ And “G’ Fast Terminal Connect to Battery Negative.
EXAMPLE OF GREEN LIGHT CONNECTION:
SPECIFICATIONS
GENERAL SPECIFICATIONS
- Nominal Diameter ………………………………………………………………….. 10″ / 254 mm
- Nominal Impedance ………………………………………………………………………… 4 Ohm
- RMS Power Handling ………………………………………………………… 200 Watts
- MAX Power Handling………………………………………………………….. 600 Watts
- Sensitivity (1w/1m) …………………………………………………………………… 94.3 dB
- Frequency Response ……………………………………………………….. 35Hz-20KHz
- Recommended Hi Pass Crossover ……………………………..50Hz
BODY – FEATURES
- UV Compliant …………………………………………… Yes, 100% Stable / Si 100% Estable
- Marine Grade Type …………………………………………………………………………. IP65
- RGB LED …………………………………………. Yes, RGB integrated / SI, RGB Integrado
- Grill Type ……… Injection Molded Composite ASA with UV Protection Coating
- Pair ………………………………………………………………………………………………………………. Yes / Si
WOOFER SPECIFICATIONS
- Voice Coil Diameter ………………………………………………. 1.5″ / 38.6mm
- Voice Coil Former Material ……………………………………………. Kapton
- Winding Material …………………………………………………………………………. CCAW
- Cone Material ………………. Injection Molded Polypropylene + UV Compliant
- Surround Material …………………………………………….Butyl (Rubber) / Goma
- Basket Material ……………………………………….. High Temp Injection Molded
Composite with UV Protection Coating
- Magnet Material ………………………………… Ferrite (Y35) + Neodymium (N35)
- Magnet Weight …………………………………………………………………………. 50 OZ + 0.56 OZ
TWEETER SPECIFICATIONS
- Voice Coil Diameter ……………………………………………………….1″ / 25mm
- Voice Coil Former Material ……………………………………………. Kapton
- Winding Material ………………………………………………………………………. CCAW
- Diaphragm Material …………………………………………………………………………..PEN
- Magnet Material …………………………………Neodymium (N38H) / Neodimio (N38H)
- Magnet Weight …………………………………………………………………………………… 0.51 OZ
THIELE & SMALL PARAMETERS
- Equivalent Volume ……………………………Vas …………………. 197.13L / 6.96ft3
- Excursion (one way) ……………………………… Xmax ……………………………………. 6 mm
- Free Air Resonance …………………………..Fs ……………………………………. 42 Hz
- Mechanical Factor ………………………………….Qms ……………………………………. 6.874
- Electrical Factor ………………………………………. Qes ……………………………………. 0.838
- Total Factor …………………………………………………….Qts ……………………………………. 0.747
- Moving Mass …………………………………….Mms ………………………………….. 11.37g
- Compliance ……………………………………. Cms ………………………….1.264 mm/H
- Bl Factor ……………………………………………………………. Bl ………………………………………… 3.4
- Voice Coil Inductance………………….Le………………………….. 0.60712mH
- Diaphragm Area ……………………………………. Sd………………………….. 333.29 cm2
- DC Resistance ……………………………………………. Re………………………………..3.2 OHM
- Efficiency Bandwidth Product
SPEAKER MEASUREMENTS
- Overall Diameter ……………………………………………………………………… 10.7″ / 274 mm
- Overall Depth…………………………………………………………………….. 5.7″ / 144.7 mm
- Front Mount Baffle Cutout ……………………………………. 8.75″ / 222 mm
- Mounting Depth ………………………………………………………….. 4.2″ / 106.6 mm
- Motor Diameter …………………………………………………………………….5.3″ / 135 mm
COLORS AVAILABLE
- Black Satin ……………………………………………………………………………………… NXL-10/BK
- White Gloss ………………………………………………………………………………….. NXL-10/WH
WARRANTY
Please visit our website DS18.com for more information on our warranty policy
DIMENSIONS
We reserve the right to change products and specifications at any time without notice. Images may or may not included optional equipment.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>