Samsung VS20T755 Vacuum cleaner User Manual
- June 5, 2024
- Samsung
Table of Contents
Samsung VS20T755 Vacuum cleaner
Product Specification
Model | VS20T755*** |
---|---|
Power | 100-240 V~ 50-60 Hz |
Rated power consumption | 550 W |
Battery specification | Lithium-ion 21.6 V, 1800 mAh, 6 cell |
Charging time | 3.5 hours |
Approximately 3 minutes (JET) / | |
Handy | Approximately 5 minutes (MAX) / Approximately 30 minutes (MID) / |
Cleaning time (Default | |
: MID) | |
Turbo Action Brush | Approximately 9 minutes (MAX) / Approximately 18 minutes |
(MID) /
| | Approximately 27 minutes (MIN)
- Charging and cleaning time may differ depending on the brushes and the conditions of use.
Safety information
- Before operating the appliance, please read this manual thoroughly and keep it for your reference.
- Because the following operating instructions cover various models, the characteristics of your vacuum cleaner may differ slightly from those described in this manual.
Caution/Warning symbols used
WARNING
Indicates that a danger of death or serious injury exists.
CAUTION
Indicates that a risk of personal injury or material damage exists.
Other symbols used
NOTE
Indicates that the following text contains additional important information.
State of California Proposition 65 Warning (US only)
WARNING
This product contains chemicals known to the State of California to cause
cancer and birth defects or other reproductive harm.
For battery recycling go to call2recycle.org or call
1-800-822-8837
Failure to meet these requirements could cause damage to the internal parts of
the vacuum and void your warranty.
General
-
Read all instructions carefully. Before switching the vacuum on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate at the rear of the handy vacuum cleaner (battery contact side).
-
WARNING :
-
Do not use the vacuum cleaner on a wet rug or floor.
-
Close supervision is necessary when any appliance is used by or near children. Do not allow the vacuum cleaner to be used as a toy. Do not allow the vacuum cleaner to run unattended at any time. Use the vacuum cleaner only for its intended purpose as described in these instructions.
-
Do not use the vacuum cleaner without a dustbin.
-
Empty the dustbin before it is full to maintain the highest efficiency.
-
Do not use the vacuum cleaner to pick up matches, live ashes or cigarette butts. Keep the vacuum cleaner away from stoves and other heat sources. Heat can deform and discolor the plastic parts of the unit.
-
Avoid picking up hard, sharp objects with the vacuum cleaner as they may damage the vacuum’s parts.
-
Do not block the suction or the exhaust port.
-
To avoid damage, remove the plug by grasping the plug, not by pulling the cord.
-
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should not clean or perform maintenance on the vacuum without adult supervision.
-
Children should be supervised to ensure that they do not play with the appliance.
-
The battery must be removed from the main unit before cleaning or performing maintenance on the vacuum.
-
The use of an extension cord is not recommended.
-
If your vacuum cleaner is not operating correctly, switch off the power supply and consult an authorized Samsung service agent.
-
If the power cord is damaged, it must be replaced by a Samsung service center to avoid any electrical hazards.
-
Do not use to suction up water.
-
Do not immerse in water for cleaning.
-
Please contact Samsung or a Samsung service center for a replacement if one is needed.
Wall mount
- Do not modify the polarized plug to fit a non-polarized outlet or extension cord.
- Do not use outdoors or on wet surfaces.
- Unplug the wall mount from the outlet when not in use and before servicing.
- Use only the wall mount supplied by the manufacturer to recharge.
- Do not use with a damaged cord or plug.
- Do not pull or carry by the cord, use the cord as a handle, close a door on the cord, or pull the cord around sharp edges or corners. Keep the cord away from heated surfaces.
- Do not use extension cords or outlets with inadequately rated current.
- Do not charge a non-rechargeable battery.
- Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
- Do not mutilate or incinerate batteries as they will explode at high temperatures.
- Do not attempt to open the wall mount. Repairs should be only carried out by a qualified Samsung service center.
- Do not expose the wall mount to high temperatures or allow moisture or humidity of any kind to come into contact with the wall mount.
Vacuum cleaner
- Do not pick up hard or sharp objects such as glass, nails, screws, coins, etc.
- Do not use without a filter in place. When servicing the unit, never put fingers or other objects into the fan chamber in case the unit accidentally turns on.
- Do not put any objects into openings. Do not use with any openings blocked. Keep openings free of dust, lint, hair, and anything that may reduce air flow.
- Do not pick up toxic materials (chlorine bleach, ammonia, drain cleaner, etc.).
- Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
- Do not use the vacuum cleaner in an enclosed space filled with vapours given off by oil based paint, paint thinner, moth proofing substances, flammable dust, or other explosive or toxic vapours.
Installation
- If you have a problem with installing the wall mount, contact a Samsung service center.
- Injury or product malfunction from not installing the wall mount correctly may not be compensated.
Power related
WARNING
- When installing the wall mount, do not bend the battery charger with excessive force or put heavy objects on the battery charger.
- Otherwise, electric shock or fire may occur.
- If there is dust, water, etc. on a pin or contact point of the power plug, wipe them carefully.
- Otherwise, abnormal operation or electric shock may occur.
- Do not pull the cord and do not touch the plug with wet hands.
- Do not plug the wall mount into a power source with the incorrect voltage. Do not plug the wall mount into a muti-outlet or power strip. Do not leave the battery charger lying on the floor. Attach the cord close to a wall.
- Otherwise, electric shock or fire may occur.
- Do not use a damaged power plug, battery charger, or loose power outlet.
- Otherwise, electric shock or fire may occur.
- If the battery charger is damaged, have a Samsung authorized service center replace the battery charger with a new battery charger.
- Otherwise, electric shock or fire may occur.
Operation
WARNING
- Do not touch the charging terminal of a vacuum or wall mount with chop sticks, metal screw drivers, forks, knives, etc.
- Otherwise, product malfunction or electric shock may occur.
- Make sure that the battery terminals of the wall mount do not come into contact with a conductor such as a bracelet, watch, metal rod, nail, etc.
- Make sure that any liquid such as water or juice is not allowed to enter the vacuum cleaner or the wall mount.
- Otherwise, electric shock or fire may occur.
- Do not use the wall mount for other purposes.
- Otherwise, severe damage to the wall mount or fire may occur.
- Do not vacuum liquid, blades, pins, embers, etc. during cleaning.
- Otherwise, abnormal operation or product damage may occur.
- Do not step on the product body or strike the product.
- Otherwise, an injury or product damage may occur.
- The brush and air outlet should not be blocked during cleaning.
- Otherwise, product malfunction or fire may occur due to overheating of the product.
- This product is intended for household use only. Do not use this product for heavy duty cleaning, commercial cleaning, industrial cleaning, or cleaning outdoors, especially on stone or cement. Do not use to pick up chalk powder in and around billiard tables or in hospital aseptic rooms.
- Otherwise, abnormal operation or product damage may occur.
- Do not use the product near heating appliances such as heaters, or in areas containing combustible sprays, or flammable materials.
- Otherwise, fire or product deformation may occur.
- Before using the product, make sure that the filters are correctly inserted.
- Otherwise, dust can enter the motor inside the main body and cause product damage. Suction force can decrease.
- If there is a gas leak or combustible spray is used, do not touch the power outlet and open the window for ventilation.
- Otherwise, an explosion or fire may occur.
- If the vacuum makes a strange sound or emits a smell or smoke, turn off the vacuum immediately, and then contact a Samsung service center.
- Otherwise, electric shock or fire may occur.
CAUTION
- Do not use the product near combustible material. Also do not use:
- In a place where a burning candle or desk lamp is placed on the floor.
- In an area where an unattended place heater is turned on or an area in which there are unextinguished embers in a fireplace, in an ashtray, etc.
- In a place where there are combustible materials such as gasoline, alcohol, thinner, ashtrays with unextinguished cigarettes, etc.
- Do not allow children to cling to or push the wall mount.
- Personal injury, product and floor damage may occur.
- When you need to store the vacuum cleaner for a short time during cleaning, turn the vacuum off and lay it on the floor.
- Otherwise, the vacuum cleaner may fall and could cause an injury or severe product damage.
- Do not charge the product near a window, heater, toilet, bathroom, etc.
- After using the vacuum cleaner, you should store it in the wall mount or lay it safely on the floor.
- Otherwise, the product may fall and could cause an injury or severe product damage.
- Do not store the vacuum cleaner by leaning it against a wall or table.
- Do not use the vacuum cleaner for other than its intended purpose. (Do not allow children to ride on or play with the product.)
- An injury or product damage may occur.
- Before plugging in or unplugging the wall mount, turn off the vacuum and make sure that the pins of the power plug do not come into contact with your hands.
- Otherwise, fire or electric shock may occur.
- When using the vacuum cleaner, be careful not to hurt yourself on the moving or spinning parts.
- Be careful not to suction body parts into a brush of the vacuum cleaner (Hair, etc.).
- When cleaning the wall or ceiling, use both hands.
- Use both hands to clean with the vacuum. If you clean with one hand, you can damage your wrist or drop the vacuum and cause an injury or damage the vacuum.
- When assembling the vacuum, be careful not to catch your fingers or hands in the movement fold of the handle.
- Do not use the vacuum cleaner on objects that can be easily scratched (monitors, stainless steel appliances, etc.).
- Do not store the vacuum cleaner inside a car.
- Do not use water to clean the vacuum cleaner when in use.
- Use the vacuum cleaner in dry places only.
- Do not use the vacuum cleaner in wet places or on water.
- Do not use the vacuum cleaner to pick up spilled beverages or pet waste.
- Do not use the vacuum cleaner in direct sunlight or high heat.
Maintenance
WARNING
- Before removing foreign matter inside the vacuum, turn off the vacuum cleaner first.
- If the vacuum is on while you are removing the foreign matter, you can hurt yourself or damage the vacuum.
- When cleaning the exterior of the product, turn off the product first and then wipe it with a dry towel. Do not spray water directly onto the product or wipe it with volatile materials such as benzene, thinner, or alcohol.
- If water gets into the product and an error occurs, turn off the product and contact a Samsung service center.
- Unplug the charging stand before cleaning it.
- When cleaning the washable parts, do not use alkaline detergent, acid, industrial detergent, air freshener, acetic acid, etc.
- Otherwise, product damage such as plastic breakage, deformation, discoloration, printing deterioration, etc. may occur.
Washable Parts| Dustbin, washable micro filter, Fine Dust Filter, metal mesh grille filter, dry cloth
---|---
Acceptable detergent| Neutral| Dish washing detergent
Prohibited detergent
| Alkaline| Lox, mold cleaner, etc.
Acid| Paraffin oil, an emulsifier, etc.
Industrial cleaners| NV-I, PB-I, Opti, alcohol, acetone, benzene, thinner,
etc.
Air freshener| Jet spray air fresheners (coffee flavor, herb, etc.)
Oils| Animal oils, vegetable oils
Etc.| Edible acetic acid, vinegar, glacial acetic acid, etc.
CAUTION
- Do not push the vacuum cleaner while it is stored in the wall mount.
- Personal injury, floor and product damage may occur.
INSTALLATION
Name of the parts
NOTE
The wave pattern on the exterior of the product is a natural appearance due to
the use of pearl plastic materials and its pearl distribution.
- Pipe
- Dustbin
- Metal mesh grille filter
- Washable micro filter
- Fine Dust Filter
- Dustbin release button
- Display
- Power( ) button
- Suction power control button
- Handle
- Battery level indicator
- Battery release button
- Pipe release button
- Brush release button
- Vacuum charging part
- Accessory holder
- Battery charger
Battery Spec
- VS20T755*** Series : Lithium-ion 21.6 V, 1800 mAh, 6 cell
Accessories
Accessories may differ depending on the models.
-
Pipe
-
Combination Tool
-
Extension Crevice Tool
-
Battery (2 units)
-
Wall mount (Screws: 2 units / Screw anchors: 2 units)
-
Battery charger
-
User manual
-
Mini Motorized Tool
-
Soft Action Brush
-
Turbo Action Brush
-
Flexible Tool
-
Clean station
-
Optional
Installing the wall mount
CAUTION
- The wall mount’s mounting screws must be affixed to a hard wall or underlying wall stud.
- If you install the wall mount into drywall, you must screw the supporting screws into an underlying stud.
Assembling the wall mount
To disassemble the wall mount, follow
steps in reverse order.
Installing the wall mount
-
The wall mount installation should be set so the top of the wall mount is 113 cm (44 1/2 in)from the floor.
-
Using the wall mount as a template, mark where the screw holes will be placed.
-
Drill the holes to a depth of 50 mm (2 in) using a 6 mm (1/4 in) drill bit, and put the provided screw anchors into the hole.
-
ix the wall mount to the wall with the
provided screws. -
Plug in the wall mount, place the vacuum into the wall mount, and then confirm that the battery level indicator is displayed.
- Please refer to the QR code for detailed information on the installation of the wall mount.
Using the vacuum cleaner
Using the wall mount Charging
- Make sure the back of the battery is correctly placed onto the vacuum charging part.
- Check if the battery level indicator is displayed while charging.
The battery level indicator blinks while charging. When charging is complete,
the blinking stops and the light level dims.
Storing the accessories Wall mount
- When accessories are disassembled to be stored, dust may fall from the suction part of the vacuum cleaner.
- After cleaning, operate in MAX mode for 10 seconds.
Desk charger
- Place the desk charger on a desk after folding the accessory holders and assemble the accessories to the holders as shown in the picture.
- If the Extension Crevice Tool is inserted first, the accessory holders can be folded more easily
Charging the battery
When the battery level indicator is at its lowest level and blinks( ) charge
the battery.
- When charging the vacuum, make sure the connection part of the wall mount is correctly connected.
- The vacuum cleaner cannot be used while it is charging.
CAUTION
- Before ejecting the battery, the product must be turned off. (If the battery is forcibly ejected while the vacuum is operating, the vacuum can malfunction.)
- Be careful not to drop the battery. If you do, you can injure yourself or damage the battery.
Ejecting the battery Press the battery release button at the rear of the handle
to eject the battery.
Re-inserting the battery Push the battery to the end until you hear it click.
Charging with a desk charger
- Charge the battery at the desk charger.
- Push the battery in firmly.
- Check if the battery level indicator is displayed while charging.
- Operating the vacuum cleaner
If the brush clings to floors (such as a carpet, a mat, or bedding, etc.) or does not spin properly, change the suction power to ‘MIN’ or ‘MID’ mode.
Power ( ) on / off When pressing the power button, the vacuum cleaner starts
operation in ‘MID’ mode.
Controlling suction power You can control the suction power of the vacuum cleaner.
- + button: Increases suction power.
- – button: Decreases suction power.
- ‘JET’ mode: Hold the [+] button down for 3 sec. while in ‘MAX’ mode.
- The ‘JET’ mode is not displayed separately on the screen.
Checking the display
- Clogged: Something is clogging the dustbin, pipe, or the connected suction accessory.
- Spinning brush stuck: Something is stuck in the connected spinning brush accessory.
- The spinning brush stuck display will not turn on if the spinning brush motor stops because it has overheated.
- No Filter: The washable micro filter is not assembled correctly
- Suction power: Displays the current suction power.
If either 01, 02, or 03 blinks a few times and the vacuum cleaner stops
operation, please take action by referring to the maintenance part of this
manual.
Using the accessories
If the spinning brush stops working, check whether it has overheated or has
something stuck in it. (Please refer to the troubleshooting part of this
manual.)
Disassembling the accessories
- When disassembling the pipe, press the release button at the rear of the pipe.
- Before disassembling the accessories, operate in MAX mode for more than 10 seconds to clean the accessories of any remaining dust or foreign matter.
- When disassembling the brush, press the release button at the rear of the brush.
Soft Action Brush Use to
clean a wood or linoleum floor.
Turbo Action Brush Use to clean various floor conditions at home, it is also
suitable to clean carpet.
Mini Motorized Tool Use to clean bedding.
Combination Tool Use to
remove dust from curtains, furniture, sofas, etc.
Extension Crevice Tool Use to remove dust from grooves of window frames, chinks,
corners, etc.
Flexible Tool Use to clean
the places hard to reach such as the upper or rear parts of furniture, or
ceilings.
NOTE
The Flexible Tool can only be connected to the Combination Tool or the
Extension Crevice Tool.
Maintaining the vacuum cleaner
CAUTION
- Turn off the vacuum cleaner before cleaning it.
- If the dustbin or filter is filled with dust, the vacuum cleaner may stop to prevent overheating.
- You should clean the dustbin or filter before it fills to the MAX line.
When to empty the dustbin Emptying the dustbin easily
If you use the clean station, you can empty the dustbin without causing dust
clouds.
Emptying and cleaning the dustbin
- After pressing the dustbin release button,
- pull the dustbin in the direction of the arrow.
-
Pull the washable micro filter out by pulling up on the filter handles inside the washable micro filter. (marked PULL)
-
While pressing the button, turn the dustbin cover and remove it from the dustbin.
-
Brush the dust off the metal mesh grille filter with the combination tool.
-
Do not pull the rubber attached to the metal mesh grille filter.
-
After emptying the dustbin, clean it and dry in the shade.
-
When heat is applied, product malformation may occur.
-
Reassemble the dustbin cover aligning the dustbin release button with the groove of dustbin.
-
Put the washable micro filter in the dustbin cover by fitting in grooves of the dustbin cover.
-
Assemble the dustbin to the vacuum in the order shown in the image by pushing it until you hear it click.
Cleaning the filter
- To maintain the best performance of the filter, remove the dust on the filter frequently and clean the filter with water once a month.
- After cleaning, dry completely for more than 24 hours in the shade before use.
- When heat is applied, product malformation may occur.
Washable micro filter
Fine Dust Filter
When
assembling, turn the filter until the line below the lock image is not
visible.
Cleaning the accessories
- Mini Motorized Tool
- Extension Crevice Tool / Pipe
Soft Action Brush
NOTE
When- foreign matter remains on the brush, remove it with a wet tissue or a
dry cloth.
CAUTION
- Do not clean the spinning brush and suction part with water.
- Do not use the Soft Action Brush to remove moisture such as spilt liquid or pet’s waste.
Turbo Action Brush
- If the foreign matter is not removed, use scissors to remove it.
NOTE
- If a or other foreign matter is vacuumed up and tangled with the spinning brush, the spinning brush will stop working to protect the brush motor. After cleaning the brush, turn the power off and then on again.
- If a brush does not work after cleaning, turn the power off and then on again.
- When cleaning the brush, be careful not to catch your fingers in the fold of the brush.
Notes and cautions
Battery usage
NOTE
- If your vacuum cleaner does not work after you charge the battery, change the battery. If it still does not work with the new battery, contact a Samsung service center.
- When you purchase a battery in a Samsung service center, check for the genuine Samsung logo on the battery ( ) and the battery name (VS20T755*** Series: VCA-SBT90EB).
CAUTION
- Do not disassemble the battery or the wall mount.
- Do not apply heat to the battery and do not put the battery in a fire.
- As the battery is manufactured only for this product, do not use the battery for other electronic appliances or other purposes.
- Removing the battery during operation may cause product malfunction.
- If the battery is removed while the vacuum cleaner motor is operating, the battery may not work for 30 seconds after being re-attached for safety reasons.
- Battery charging time and usage time may shorten with increased battery use. When the battery no longer charges or runs down quickly, replace the exhausted battery with a new one.
- Use only the wall mount and batteries provided by Samsung.
- Before inserting the battery, confirm that the battery is being inserted in the correct direction and orientation.
- When discarding a dead battery, put it into a battery collection box for recycling.
- If you are not going to use your vacuum cleaner for a long time, detach the battery from the vacuum.
- When attaching the battery to the vacuum, insert it until you hear a click. This assures that the battery is firmly attached.
- Otherwise, the battery may fall and could cause product damage or injury.
- Do not drop or strike the battery or subject it to a sudden shock.
- Do not disassemble the battery and make sure that you do not create a short circuit across the plus (+) and minus (-) terminals.
- Leaks from battery cells can occur under extreme usage or temperature conditions. If the liquid gets on your skin, wash the affected area quickly with water. If the liquid gets into your eyes, flush them immediately with clean water for a minimum of 10 minutes. Seek medical attention.
- To protect the motor and battery, the vacuum cleaner may not operate when the temperature is lower than 5 °C or higher than 45 °C.
- If you are not going to use the vacuum for a long period of time or you’re going to be away from home for a long period of time, unplug the wall mount, and then detach the wall mount from the battery. When the battery is not being charged and not being used, it will slowly discharge.
- When the battery level is low, recharge it. If the level of the battery remains low for a long period of time, it can cause the performance of the battery to degrade.
Operation
NOTE
- If excessive force is applied to a brush or foreign matter is caught in the spinning brush, the brush may stop working to protect the motor or vacuum. Turn the vacuum off, remove the foreign matter, and then turn the vacuum on. If the vacuum does not start, turn it off and then on again.
- Static electricity may occur depending on the humidity, temperature, or floor material, etc. in your home. If it happens repeatedly, contact a Samsung service center.
- Please charge the battery fully:
- Before using a newly purchased battery for the first time or if you haven’t used the battery for a long time.
- When the battery level indicator is on the lowest indication and blinks.
CAUTION
- When the spinning brush inside a brush is working, do not touch the brush.
- Otherwise, your hand can be caught and it may cause an injury.
- Do not use the vacuum cleaner on items that can be scratched (TV and monitor screens, etc.
Maintenance
NOTE
- Sometimes the wheel of a brush can scratch the floor. Before using the vacuum cleaner, check the wheels of the brush.
- If there is foreign matter on the wheel of the brush which cannot be removed easily, contact a Samsung service center.
CAUTION
- Storing the vacuum cleaner in sunlight for long hours may cause parts of the vacuum to deform or discolor. Therefore, after cleaning the parts of the vacuum cleaner, dry them in the shade.
- Do not clean the brush of the vacuum cleaner with water. Cleaning it with water can cause the brush to deform or discolor.
- Before cleaning the wall mount, you must unplug the wall mount.
- If you notice a continuous reduction in suction or the vacuum cleaner overheats abnormally, replace the Fine Dust Filter.
- After cleaning , , or with water, dry in the shade.
- When heat is applied, product malformation may occur.
Troubleshooting
Before calling for service, review the problems and solutions below. If none of the suggested solutions resolve your problem, please visit our website at www.samsung.com or call Samsung Customer Care. Note that you will be charged for any service calls in which no defects were found.
Problems | Solutions |
---|---|
The vacuum cleaner does not work. |
- Check the battery level and charge the battery
- Check whether the product is turned off, and then press the power button to turn it on.
- Check whether the pipe, dustbin or brush is blocked.
- Check whether the washable micro filter is inserted correctly.
- If the vacuum has not been used for a long time, charge the battery.
- If the battery dies, replace the battery.
Suction force decreases suddenly and the vacuum makes a vibrating sound.|
- Check whether a brush, dustbin or pipe is clogged with foreign matter and remove it
- Check whether the dustbin is fully filled with dust. If it is, empty the bin.
- Check whether the filter is dirty. If it is, clean the filter.
The vacuum cleaner cannot be charged.|
- Check if foreign matter (dust) is on the charging terminal. Remove any foreign matter with a cotton swab or soft cloth.
- Check that the vacuum cleaner is properly aligned on the charging station and the LED of the battery level indicator is turned on
- Confirm that the voltage provided to the wall mount matches the requirements of the wall mount.
The spinning brush does not work.|
- Turn off the vacuum and check whether the brush is clogged with foreign matter. If so, remove the foreign matter and restart the vacuum.
- If the brush still does not spin, turn the vacuum cleaner off and back on a second tim
- For the Soft Action Brush, if the vacuum overheats, it may take about 30 minutes for the motor to cool.
An odor is coming from the air outlet or filter of the vacuum cleaner.|
- Empty the dustbin and clean the filters frequently
- As your vacuum cleaner is a new product, it may have a slight odor for the first 3 months after purchase.
- If you use the vacuum cleaner frequently, accumulated dirt in the dustbin or dust on the filter may generate an odor
- Replacement filters are available at your local Samsung service agent.
Problems
|
Solutions
---|---
Cleaning is finished but small dust particles come out of the brush.|
- After cleaning, operate the vacuum for 10 seconds or more on the MAX setting to suction up the small dust particles.
Vacuum cleaner stops operation during cleaning.|
- The vacuum cleaner’s motor will shut off to prevent overheating
- When the vacuum operates with a full dustbin.
- When the vacuum operates with suction part or brush clogged.
- When the Extension Crevice Tool is used for long hours.
- After correcting the cause of the problem, turn the product on again. (This case may differ depending on the ambient temperature.)
Static electricity occurs when cleaning a thick and soft mat.|
- Some types of mats such as a (childcare center mat or a noise prevention mat for between floors, etc.) may cause static electricity
- Move the brush on a normal floor for a while and clean again. This should get rid of the static electricity.
Product specifications
Model
| VCA-SAE90*
---|---
Power|
120 V, 60 Hz
Weight
| 5.6 kg
Size
|
W 180 mm x D 185 mm x H 600 mm (W 7.09 in x D 7.28 in x H 23.62 in)
NOTE
- The wave pattern on the exterior of the product is a natural appearance due to the use of pearl plastic materials and its pearl distribution.
Accessories
- Dust bag: 2 units (Inside the product: 1 unit / Spare: 1 unit)
- Power cord
NOTE
If you want to purchase an additional dust bag, check the model name (VCA-
ADB90) and Samsung logo (SAMSUNG) ) first, then contact your nearest Samsung
Electronics retailer or Samsung service center.
PREPARATION
Safety Information
The following contents are written for users’ safety and prevention of
property damage. Before using the product, please read this manual thoroughly
and use the product correctly.
- For safety reasons, people with physical, sensory difficulties, or mental disorder, lack of experience and knowledge should not use this product without the supervision of their guardians.
Caution/Warning symbols used
WARNING
Indicates that a danger of death or serious injury exists.
CAUTION
Indicates that a risk of personal injury or material damage exists.
Other symbols used
NOTE
Indicates that the following text contains additional important information.
State of California Proposition 65 Warning (US only)
WARNING
This product contains chemicals known to the State of California to cause
cancer and birth defects or other reproductive harm.
For battery recycling go to call2recycle.org or call
1-800-822-8837
Failure to meet these requirements could cause damage to the internal parts of
the vacuum and void your warranty.
General
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should not clean or perform maintenance on the vacuum without adult supervision.
Installation
CAUTION
- The clean station should be placed and used on a stable floor.
- If the product falls over, an injury or product and floor damage may occur.
- Do not place or use the product on an uneven floor, a carpet, a living room table, or a desk etc.
- If the product falls over, an injury or product and floor damage may occur.
- Do not place the product at a wall behind which pipes (gas or water etc.) or electrical cables are installed.
- Do not install the product near water, in an area with excessive moisture, or near windows, etc.
- Do not install the product in a place where people frequently pass by, near an entrance, or a narrow passage.
- If people trip over the product, an injury or product damage may occur.
Power related
WARNING
- Do not bend the power cord with excessive force or put heavy objects on the power cord.
- Otherwise, electric shock or fire may occur.
- If there is dust, water, etc. on a contact point of the power plug pins, wipe them carefully.
- Otherwise, abnormal operation or electric shock may occur.
- Do not pull the power cord and do not touch the power plug with wet hands.
- Otherwise, electric shock or fire may occur.
- Do not use a power source with the incorrect voltage. Do not use a multi-plug outlet or power strip for the product. Do not leave the power cord lying on the floor. Attach the cord close to a wall.
- Otherwise, electric shock or fire may occur.
- Do not use a damaged power plug, power cord, or loose power outlet.
- Otherwise, electric shock or fire may occur.
- If the power cord is damaged, have a Samsung authorized service center’s qualified repairman replace the power cord with a new power cord.
- Otherwise, electric shock or fire may occur.
- Except for an authorized repairman, do not disassemble or modify the clean station.
- When using the product in a veranda, make sure the power cord and the power plug do not touch water.
Operation
WARNING
- Static electricity may occur depending on the humidity, temperature, or floor material, etc. of your operating environment. If it happens repeatedly, contact a Samsung service center.
- Do not cause a short circuit by touching the power terminal with utensils, metal screw drivers, etc.
- Otherwise, product malfunction or electric shock may occur.
- Make sure that any liquid such as water or juice does not touch inside or outside the product.
- Otherwise, electric shock or fire may occur.
- The clean station is manufactured for Samsung Jet wireless vacuum cleaner only, so do not use the clean station for other purposes.
- Do not use the product near heating appliances such as heaters, or in areas containing combustible sprays, or flammable materials.
- Otherwise, fire or product deformation may occur.
- If there is a gas leak, or a combustible spray is used such as a dust remover, do not touch the power outlet and open the window for ventilation.
- Otherwise, an explosion or fire may occur.
- If the product makes a strange sound or emits a smell or smoke, turn off the product immediately, and then contact a Samsung service center.
- Otherwise, electric shock or fire may occur.
CAUTION
- Do not allow children or a pet to ride on or play with the product.
- If the product falls over, an injury or product and floor damage may occur.
- When moving the product, you should grip it with both hands. NOTE
- When the dust bag of the clean station is filled with dust, the product may stop temporarily due to the overheating prevention device of the motor. Replace the dust bag and operate the product again.
- As a new product, it may have a slight odor for the first 3 months after purchase.
Maintenance
WARNING
- When cleaning the exterior of the product, unplug the product first and then wipe it with a dry towel. Do not spray water directly onto the product or wipe it with volatile materials such as benzene, thinner, or alcohol.
- Otherwise, product damage such as plastic breakage, deformation, discoloration, printing deterioration, etc. may occur.
CAUTION
- Do not push the clean station in case it falls over.
- Personal injury, floor and product damage may occur.
- When the clean station emits bad odor, replace the dust bag or clean the filters.
- When you pull the power cord out of the groove at the bottom of the clean station, do not pull it hard. Turn the cord gently on its side so that it can come out without interruption.
- Otherwise, the power cord may get damaged and could cause an electric shock or fire.
Installing the clean station
Installation guide
- As the outlet is at the rear of the product, do not put the product close against a wall, allow 10 cm (4 in) space between the wall and the product, and place the product on a stable floor.
- Put the power cord into the groove at the bottom of the clean station, arrange the cord neatly along the wall and plug the product in.
- Leaving the cord out on the floor can lead to the power cord being damaged or cause a tripping hazard.
- When the clean station is plugged in, the status indicator turns ‘blue’ and then turns off.
- Please refer to the QR code for detailed information on the use of product and cleaning methods.
Using the clean station
The clean station is compatible with the provided dustbin only.
Press the
[PUSH] button on the upper cover of the clean station.
Insert the
dustbin into the clean station. Dust is ejected automatically.
- When the clean station is in operation, the status indicator turns ‘blue’.
- Press the [Start/Stop] button to stop operation.
When the clean station’s operation stops completely, pull the dustbin out and close the clean station by pressing the upper cover firmly. NOTE
- If dust still remains inside the dustbin even after using the clean station, press the [Start/Stop] button to operate the clean station.
- Press the button again to stop operation.
- If the dustbin is filled with dust and will not eject it properly, push the washable micro filter down with your hand, and then operate the clean station.
- When there are foreign object residues, remove them by referring to ‘Maintaining the clean station’ section of the manual.
CAUTION
- After using the clean station, you should close the dustbin by pressing the bottom cover firmly until you hear it ‘click’.
Maintaining the clean station
Dust bag
Time to replace a dust bag
- When the status indicator turns ‘red’, you should replace the dust bag.-
- Grip both sides of the front cover and pull the cover towards you.
- Open the cover by pulling the [PULL] button.
Press the ‘PUSH’ lever.Pull the ‘PULL’ lever out in a diagonal direction and remove the dust bag.Insert a new dust bag towards the back and push the ‘PULL’ lever upward firmly until you hear it ‘click’.
- Be cautious not to assemble incorrectly when inserting the dust bag.
After replacing the dust bag, assemble the clean station in reverse order.
NOTE
- If the dust bag emits a bad odor even though it is not filled with dust, replace the dust bag.
- When you operate the clean station after replacing the dust bag, the status indicator changes from red to blue.
Premotor Filter
- Lift up the Premotor Filter inside the product and pull it out. Then, detach the nonwoven fabric from the filter.
- Remove the dust on the nonwoven fabric by shaking it and reassemble the Premotor Filter.
Fine Dust Filter
- Do not clean the Fine Dust Filter with water. Shake the filter.
- To maintain the best performance of the Fine Dust Filter, replace the filter once a year.
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
Country | Customer Care Center | Web Site |
---|---|---|
CANADA | 1-800-SAMSUNG (726-7864) | [www.samsung.com/ca/support |
](http://www.samsung.com/ca/support)(English)
1-844-SAM-PAYS (726-7297)| www.samsung.com/ca_fr/support
(French)
U.S.A| 1-800-SAMSUNG (726-7864)
1-844-SAM-PAYS (726-7297)
References
- Call2Recycle | Leading the Charge For Battery Recycling
- Aide et assistance : produits | Samsung Canada
- Product Help & Support | Samsung CA
- Support Home | Official Samsung Support US
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>