SEMES SSD-100 Smoke and Temperature Detection User Manual
- June 9, 2024
- SEMES
Table of Contents
SEMES SSD-100 Smoke and Temperature Detection
Product Overview
It is a stand alone smoke and temperature detector designed to be used in various industrial production lines such as distribution boards.
- Smoke Detection Method (Light Scattering) Alarm function to notify of fire by detecting smoke caused by fire
- Stand Alone alarm Detecting Smoke and sounds a Smoke alarm to notify people of the occurrence of a fire
- Built-in Temperature sensor (PT100)
Package Content
Product Function and How To Use
Unit Layout and Function
| No | Description | Function |
|---|---|---|
| 1 | Alarm Buzzer | Alarm Sounds in case of Fire (1second on/1second off) |
2
| ****
Reset Switch / LED
| Turn alarm sounds off or operation testing Status display LED
3| Screw Cap| Screw Cap
4
| ****
Input / Output Port
| DC 24V Voltage input.
Relay input / output & temperature sensor_PT100 input / output
| Status | Relay Contact | Operating |
|---|---|---|
| Power on | B contact | Normal |
| Power off | A contact | B à A contact |
| Smoke Alarm On | A contact | B à A contact |
| Reset Alarm sound | B contact | A à B contact |
LED Operation
| LED Indication | Status Description |
|---|---|
| Green LED ON | Normal Status |
| Red LED Blinking | Smoke Detection (Red LED 1second on/1second off) |
Red LED ON
| Short Key : Red LED On until Alarm sound Off Long Key : maintenance mode
General Operation (Mode Description)
- (Smoke monitoring mode) Once power is applied properly with correct power connection, Green LED will be ON and Relay is connected to B contact.
- (Smoke detection mode) When device detect smoke by fire, Red LED will be blinking and sounds alarm.
- Operator click the Reset switch in order to reset device which is in Smoke detection mode,. Alarm sounds will be OFF and Red LED will be ON until device come to smoke monitoring mode back. In Smoke monitoring mode, LED will change to Green color
Maintenance mode
- Push reset switch for 3 seconds in Smoke monitoring mode, Red LED will be On and alarm sounds.
- Once click reset switch again, Alarm sound will be off and LED will be changed green color.
Installation instruction
How to install
Input/output pin-map
| No | name | Connection |
|---|---|---|
| 1 | 24V | DC24V connect (Less than 30 m) |
| 2 | GND | DC GND connect |
| 3 | FG | Ground |
| 4 | R1 | Relay input |
| 5 | R2 | Relay B contact |
| 6 | PT1 | PT100 A terminal |
| 7 | PT2 | PT100 B terminal |
Caution
- When wiring to the terminal block, please be careful not to allow foreign objects such as dust or wire sheath to enter the connection terminals and the inside of the product.
- When mounting and wiring, make sure to disconnect the external power source.
- Please use device in the prescribed temperature range. Otherwise, the product may malfunction and break.
- Please use within the rated voltage and current ranges. When device used outside of prescribed range. the product may malfunction and break.
- Please read the product manual carefully and check the product rating, connection diagram, appearance specifications, etc.
- This product is an optical smoke detector that avoids dusty places, areas affected by wind, and places where the lighting shines directly on the product, etc., and please carefully monitor the installation environment and install and use it.
- Use by installing at a distance of 60 cm from the wall.
- Install and use in a place that is not affected by air conditioners and fans.
- Install and use at a distance of at least 1 meter from the lights
- In the event of an abnormality in the product, do not arbitrarily disassemble it and exchange it at the place of purchase.
- When using the product, please take care not to get debris around the product and on the exterior of the smoke chamber in the product. (This causes malfunctions.)
- Test in check mode every 1 month to make sure there are no abnormalities in the product.
Specification
| No | Category | Description |
|---|---|---|
| 1 | Model Number | SSD-100 |
| 2 | Model Type | DC 24V, Photo-electric type2, non-waterproof |
| 3 | Power | DC 24V / current 50mA |
| 4 | Operating condition | -10℃~60℃ / Humidity 10%~ less than 90% |
| 5 | Alarm sounds | Bigger than 85dB |
| 6 | Detection Method | Photo-electric (Light-scattering) |
| 7 | Temperature sensor | PT100 |
| 8 | Dimension / Weight | 90.0 x 102 x 35.7 (mm) / 130g |
| 9 | Certification | CE, FCC, KC , KFI Report. |
| 10 | Intended use environment | Industry |
Warning Information
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Manufacturer and Distributor
| Manufacturer | SEMES / Republic of Korea |
|---|---|
| Distributor | Bridge Builder / 010-2740-5634 |
| After Service | 02-2699-7536~7 |
| Address | **77, 4sandan 5-gil, Jiksan-eup, Seobuk-gu, Cheonan-si, |
Chungcheongnam-do, Republic of Korea**
Documents / Resources
|
SEMES SSD-100 Smoke and Temperature
Detection
[pdf] User Manual
SSD-100, SSD100, 2AN5B-SSD-100, 2AN5BSSD100, SSD-100 Smoke and Temperature
Detection, SSD-100, Smoke and Temperature Detection, Temperature Detection,
Detection
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>