ifi ZEN-Phono-3 Phono Stage For Turntables User Manual
- June 6, 2024
- ifi
Table of Contents
if ZEN-Phono-3 Phono Stage For Turntables
Thank you for purchasing the Phono from the ZEN series. The Phono 3 is a balanced MM/MC phono stage. Unleash the full potential of your favorite vinyl records with the ZEN Phono 3. It boasts an intelligent subsonic filter that transforms the sound of your warped vinyl records, a noise floor quieter than some Class A+ phono stages, providing greater dynamic range and supports four MC/MM gain selections to ensure compatibility with a wide range of cartridges. The ZEN Phono 3 creates a serene listening experience that allows every musical detail to shine through.
FEATURES
- Supports four MC/MM gain selections from 36dB to 72dB and four input impedance settings, ensuring compatibility with a wide range of cartridges
- Features intelligent subsonic filter to intelligently remove only the ultra-low frequencies caused by warps, not by the music, unlike typical bass-reducing filters
- With an EIN (Equivalent Input Noise) of -151dBV, this phono stage surpasses some Class A+ models by 20dBV, ensuring a super-silent noise floor
- Precise RIAA with balanced output, performance matches that of a $1,000 phono stage
- Internal high-tech 1.2MHz clean power supply, rivaling classic tube amplifiers’ LC filtering circuits
Contents
- Power switch
- MM and MC gain channel display LED
- Load Mode Selector Switch
- SUBSONIC Filter ON/OFF
- Balanced 4.4mm analog line output
- RCA analog line output
- Ground
- RCA analog line input
- Gain channel switch
- DC 5V Power Supply Connection
Power switch
Power switch, short press to switch on/off.
Note: If the device has been switched on for some time (≥10 minutes), you need to shut off the unit twice to turn it off. It only happens if the unit is on for a while. This is because the MCU will have switched out of the signal path so you get to enjoy the best sonics!
MM and MC gain channel display LED
The LEDs indicate the currently selected gain mode (see item 9).
| LED | Gain mode (9) | Output Voltage |
|---|---|---|
| MM | 1 MM | ＞2mV |
| HIGH | 2 MC HIGH | ≤2mV |
| LOW | 3 MC LOW | ≤0.5mV |
| V-LOW | 4 MC V-LOW | ≤0.25mV |
Tips: ZEN Phono3 automatically enters the lock state after working for ≥10 minutes, it can not be adjusted after locking, you need to press the intelligent subsonic filter switch (4) briefly to unlock it, and it can be adjusted normally after unlocking.
Load Mode Selector Switch
This button cycles between 4 load levels:
| Load | Mode |
|---|---|
| 200pF (Default is 100pF) | MM/MC HIGH |
| 1kΩ/400Ω/100Ω | MC LOW/MC V-LOW |
Tips: ZEN Phono3 automatically enters the lock state after working for ≥10 minutes, it can not be adjusted after locking, you need to press the intelligent subsonic filter switch (4) briefly to unlock it, and it can be adjusted normally after unlocking.
SUBSONIC Filter ON/OFF
This is the SUBSONIC filter switch. The iFi-designed subsonic filter will intelligently detect whether a subsonic frequency is a warp or a bass note. It will eliminate the warps and let all the bass and mid-range frequencies pass through untouched. Therefore, it will not affect the sound quality.
Balanced 4.4mm analog line output
This is an analog output via 4.4mm > XLR or other balanced interconnects. You
can use this to connect to active speakers or amplifiers that have a volume
control.
Tip: As ZEN Phono 3 is balanced, this is the recommended output.
RCA analog line output
This is an analog output via RCA > RCA or other single-ended interconnects.
You can use this to connect to active speakers or amplifiers that have a
volume control.
Ground
This is the ZEN Phono 3’s ground, please connect it to the turntable’s
grounding wire.
RCA analog line input
This is an analog input. Connect your turntable to the ZEN Phono 3 here.
Gain channel switch
This switch switches between 4 gain levels:
| Gain Channel | Corresponds Gain |
|---|---|
| 1. corresponds to MM | (>2mV) |
| 2. corresponds to MC HIGH | (≤2mV) |
| 3. corresponds to MC LOW | (≤0.5mV) |
| 4. corresponds to MC V-LOW | (≤0.25mV) |
Please adjust the gain channel switch in accordance with your preference and your turntable’s specifications.
DC 5V Power Supply Connection
The ZEN Phono 3 is powered by a 5V supply only. Please connect the ZEN Phono 3
to the enclosed power supply.
Tip: For best performance upgrade the enclosed power supply to a super- low noise power adapter such as iPower2 5V or iPower X 5V.
SPECIFICATIONS
| Analogue Input: | RCA L/R |
|---|---|
| Analogue Output: | Balanced 4.4mm |
| Max.^ Output Voltage RMS: | RCA L/R |
| Balanced | ≤19.98V RMS 100kΩ (THD + N <1%) |
| --- | --- |
| ≤12.75V RMS 600Ω (THD + N <1%) | |
| Single-Ended | ≤10.07V RMS 100kΩ (THD + N <1%) |
| ≤7.94V RMS 600Ω (THD + N <1%) | |
| Output impedance: | |
| Balanced | ≤200Ω |
| Single-Ended | ≤100Ω |
| Input impedance: | |
| MM/MC HIGH | 47kΩ 100pF or 200pF (optional) |
| MC LOW/MC MC V-LOW | 1kΩ or 400Ω or 100Ω (optional) |
| Gain settings | |
| MM | 36dB (±1dB) |
| MC HIGH | 48dB (±1dB) |
| MC LOW | 60dB (±1dB) |
| MC V-LOW | 72dB (±1dB) |
| SNR: | (All 2V Balanced/1V Single-Ended) |
| MM | 91dB (A-weighted) |
| 82dB (unweighted 80kHz BW) | |
| MC HIGH | 81dB (A-weighted) |
| 71dB (unweighted 80kHz BW) | |
| 80dB (unweighted 80kHz BW) | |
| --- | --- |
| MC V-LOW | 78.6dB (A-weighted) |
| 69dB (unweighted 80kHz BW) | |
| Ein (equivalent input noise): | (All 2V Balanced/1V Single-Ended) |
| MM 8.9nV | /Hz (unweighted) |
| -118dBV (unweighted) | |
| MC HIGH 7.95nV | /Hz |
(unweighted)
|
-129dBV (A-weighted)
| -119dBV (unweighted)
MC LOW 0.7nV|/Hz
(unweighted)
|
-149.6dBV (A-weighted)
| -140dBV (unweighted)
MC V-LOW 0.63nV|/Hz
(unweighted)
|
-150.6dBV (A-weighted)
| -141dBV (unweighted)
Total Harmonic Distortion:| (All 2V Balanced/1V Single-Ended @ 600Ω)
MM| <-91dB/0.0027%
MC HIGH| <-80dB/0.0095%
MC LOW| <-70dB/0.031%
MC V-LOW| <-73dB/0.022%
General|
---|---
Channel Separation:| >75dB (1kHz all modes)
Frequency Response:| 20Hz – 20kHz (±0.15dB)
| 20Hz – 80kHz (±3dB)
Power Supply Requirement:| DC 5V/0.5A (centre +ve)
Power Consumption:|
No Signal| ~1.5W
Max Signal| ~1.8W
Dimensions:| 158 x 115 x 35 mm (6.2″ x 4.6″ x 1.4″)
Net Weight:| 456 g (1.0 lbs)
Limited Warranty:| 12 months
_12 months typical or as permitted/required by local reseller laws.
**Specifications are subject to change without notice.
^See FAQ at ifi-audio.com for more information._
Documents / Resources
| ifi
ZEN-Phono-3 Phono Stage For
Turntables
[pdf] User Manual
ZEN-Phono-3 Phono Stage For Turntables, ZEN-Phono-3, Phono Stage For
Turntables, Stage For Turntables, Turntables
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>