TORKLIFT CENTRAL WH91265 T-Connector Honda Civic Sedan Instruction Manual

WH91265 T-Connector Honda Civic Sedan
Instruction Manual

Installation Instructions

WARNING
ALWAYS read and follow all warnings and instructions included with the purchase before beginning installation. Keep for future reference.
DO NOT exceed the lower towing manufacturing rating (including in your vehicle owner’s manual) or specific amperage ratings stated on the product.
ALWAYS read, understand, and follow all warnings and instructions printed on the tow vehicle’s battery.
ALWAYS wear safety glasses and use all safety precautions during installation.

TOOLS REQUIRED:

Trim Panel Remover, 10mm Socket & Ratchet or 10mm Wrench, Drill (3/32” Drill Bit), Wire Crimpers, Wire Cutters, Philips Head Screwdriver, Test-probe

1. Open hatch locates and removes trim panels covering the tail lights. Using a 10mm socket, remove the mounting screws on both driver’s and passenger’s sides, being careful not to break trim panel mounting tabs. Remove tail lights and set them aside. AB

2. Disconnect the vehicle wiring harness from both taillight sockets. Separate this connector, being careful not to break the locking tabs. All connector surfaces should be clean and free of dirt. C

3. Beginning on the driver’s side and underneath the vehicle, route the harness containing the yellow wire up through the opening between the vehicle bumper and body to the driver’s side taillight pocket.
   NOTE
   For ease of installation use a fish wire between the taillight pocket and rear fascia to pull the harness from underneath the vehicle out through the taillight pocket

4. Insert the T-One® Connector ends, with the yellow wire, between the vehicle wiring connectors and locks into place. All connector surfaces should be clean and free of dirt. C

5. Underneath the vehicle, determine a suitable mounting point behind the rear bumper fascia on the passenger’s side. mount the T-One® Connector black box using the double-sided tape provided.
   CAUTION
   Make sure the module is mounted so that the epoxy side of the module is pointed towards the ground to prevent any water buildup.
   CAUTION
   Verify what is behind any surface prior to drilling to avoid damage to the vehicle and/or personal injury. Do not drill into any exposed surfaces.

6. Locate a suitable grounding point near the Harnesses black box or such as an existing ground stud or drill a 3/32” hole and secure the white wire using the eyelet and screw provided. (Do not drill into vehicle floor or bed.) Clean dirt and rustproofing from the area.
   WARNING
   If routing the wire thru a grommet and along the exterior of the vehicle, be careful to avoid any hot pipes, heat shields, the fuel tank, or any other points that may pinch or break the wire.

7. Route harness containing the green wire underneath the vehicle up through the opening between the vehicle bumper and body to the passenger’s side taillight pocket.
   NOTE
   For ease of installation use a fish wire between the taillight pocket and rear fascia to pull the harness from underneath the vehicle out through the taillight pocket.

8. Insert the T-One® Connector end, with the green wire, between the vehicle wiring connectors and lock it into place. All connector surfaces should be clean and free of dirt.

9. Disconnect the vehicle’s Negative (-) battery cable. If not removed, remove the fuse from the yellow fuse holder (provided).  After cutting the fuse holder wire, attach the ring terminal and secure it to the vehicle’s Positive (+) battery cable. Connect the other end of the fuse holder to the black 12 ga. wire, using the yellow butt connector (provided).
   WARNING
   If routing the wire thru a grommet and along the exterior of the vehicle, be careful to avoid any hot pipes, heat shields, the fuel tank, or any other points that may pinch or break the wire.

10. Beginning from the front of the vehicle, route the black 12 ga. wire rearward along the frame rail avoiding any hot pipes, heat shields, the fuel tank, or any other points that may pinch or break the wire.

11. Connect the other end of the black 12-ga. wire to the black power wire located on the T-One® Connector’s black box, using the yellow butt connector (provided).

12. Reconnect the vehicle’s Negative (-) battery cable and install the 15 amp fuse into the fuse holder from step 9.
    WARNING
    Read and follow all warnings and cautions printed on the tow vehicle’s battery. All connections must be complete for the T-One® Connector to function properly. Test and verify the installation with a test light or trailer once installed. For the initial test, reset the vehicle’s electrical system by temporarily removing the key from the ignition.

13. Reinstall the plastic trim panels, threshold, storage covers, floor covering, and other items that may have been removed during installation, being careful not to pinch or cut the wires.
    NOTE
    Secure all loose wires and mount the Trailer Tow Harness in an accessible location with a bracket or electrical box.
    WARNING
    Overloading circuits can cause fires. DO NOT exceed stated product ratings. Read the vehicle’s owner’s manual & instruction sheet for additional information.

© 2021 Horizon Global

Documents / Resources

| TORKLIFT CENTRAL WH91265 T-Connector Honda Civic Sedan [pdf] Instruction Manual
WH91265, T-Connector Honda Civic Sedan, Honda Civic Sedan, Civic Sedan, WH91265, T-Connector
---|---

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>