TORIN JACKS AT42002R 6 Ton Jack Stands Owner’s Manual

: June 5, 2024
: Torin Jacks

Table of Contents

TORIN JACKS AT42002R 6 Ton Jack Stands
Product Specifications
Product Usage Instructions
Frequently Asked Questions
SAFETY MARKINGS
ASSEMBLY INSTRUCTIONS
OPERATION INSTRUCTIONS
WARRANTY INFORMATION
TECHNICAL SPECIFICATIONS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TORIN JACKS AT42002R 6 Ton Jack Stands

Product Specifications

Model: T42002, T42002-1, T42002X, T43002, T43002-1, T43006, T43006-1, T46002, T46002-1, T41202, T41202-1
Lifting Capacity: 2 Ton, 3 Ton, 6 Ton, 12Ton
Lifting Range Min: 10-13/16 inches to 18-5/16 inches / 27.5 cm to 46.5 cm
Lifting Range Max: 16-9/16 inches to 28-1/8 inches / 42 cm to 71.5 cm

Product Usage Instructions

Assembly Instructions:

To assemble the jack stands, follow these steps:

Install the ratchet bar into the frame with the ratchet portion aligned with the locking pawl.
Move the ratchet bar to its lowest position by raising the locking handle and guiding the bar downward.
Bend the metal tab in using a hammer and punch to prevent separation of the ratchet bar from the base frame.

Additional Instructions for Specific Models:

For Item T42002, T42002-1, T42002X, T43002, T43002-1, T43006, T43006-1, T46002, T46002-1:

1. Follow the general assembly instructions.

For Item T41202, T41202-1:

1. Follow the general assembly instructions.
2. Tighten the bolt using a wrench instead of bending the metal tab.

Frequently Asked Questions

Q: What should I do if I encounter difficulties during assembly?

A: If you face any challenges during assembly, please refer to the user manual for detailed instructions. You canalso contact our customer support for assistance.

Q: Can these jack stands be used for vehicles other than cars?

A: These jack stands are suitable for various vehicles like trucks, SUVs, and trailers. Ensure you check the weight capacity and compatibility before use.

REGISTER YOUR PRODUCT

http://www.torin-usa.com/customer-support/register-a-product.html

SCAN CODE

SAFETY MARKINGS

WARNING!

Study, understand, and follow all instructions before operating this device.
Do not exceed rated capacity.
Use only on hard, level surfaces, with less than 3 degrees of slope.
Center load on saddle.
Use as a matched pair only.
Stands are not to be used to simultaneously support both ends of a vehicle.
No alterations shall be made to this product.
Support only on areas of the vehicle as specified by the vehicle manufacturer.
Only attachments and/or adapters supplied by the manufacturer shall be used.
Use wheel chocks or other blocking device on opposing wheels before using jack stands.
Do not use jack stands for any use other than the manufacturer specified usage.
Do not use if damaged in any way.
NEVER use jack stands on a lawn mower or lawn tractor.
Do not move or dolly the vehicle while on support stands.
Do not rock the vehicle while working on or around equipment.
The following are not recommended for supporting on this equipment: Foundations, Homes, Mobile Homes, Trailers, RV’s, Campers, nor Fifth Wheels, etc.
Failure to heed these markings may result in personal injury and/or property damage.

ASSEMBLY INSTRUCTIONS

In order to prevent removal of the post from the base use a hammer and flat end punch to hammer the jack’s tab in toward to post but not touching the post. If the same stands are equipped with a bolt instead of the tab. In this case the bolt can be threaded in toward the post until the bolt bottoms out.

Item: T42002, T42002-1, T42002X, T43002, T43002-1, T43006, T43006-1, T46002, T46002-1

Install ratchet bar into frame (Fig.1) with ratchet portion of bar aligned with locking pawl (stopper).
Move the ratchet bar to its lowest position by raising the locking handle, thereby releasing the stopper, and guiding the bar downward (Fig.2).
Bend metal tab in (Fig.3) using a hammer and punch. This will help prevent inadvertent separation of the ratchet bar from base frame.

Item: T41202, T41202-1

Install ratchet bar into frame (Fig.1) with ratchet portion of bar aligned with locking pawl (stopper).
Move the ratchet bar to its lowest position by raising the locking handle, thereby releasing the stopper, and guiding the bar downward (Fig.2).
Tightening the bolt (Fig.3) using a wrench. This will help prevent inadvertent separation of the ratchet bar from base frame.

OPERATION INSTRUCTIONS

If the operator is not fluent in English, the product and safety instructions shall be read to and discussed with the operator in the operator’s native language by the purchaser/owner or his designee, making sure that the operator comprehends their contents.
Visual inspection shall be performed before each use of the stand by checking abnormal condition, such as cracked welds, leaks and damaged, loose, or missing parts if stand is believed to have been subjected to abnormal load or shock inspection shall bemade by authorized repair facility.
Equipment that appears damage or worn or operates abnormally shall be removed from service.

Use on hard level surface with less than 3 degrees of slope.
Raise Vehicle with suitable jack.
Adjust height by pulling up on ratchet bar.
The weight of the locking handle should secure the ratchet bar in desired position. To confirm this, simply push down on the locking handle. Check to ensure ratchet is secure before loading.
Carefully position jack stands so that load is centered on stand’s saddle.
Slowly lower the vehicle onto the stands.
Check to ensure vehicle is secure before working on, around or under. When used to support vehicle, use wheel chocks on all unlifted wheels in both directions to prevent inadvertent movement.
DO NOT jack or dolley while jack stands are supporting the vehicle.

TO LOWER LOAD

Ensure that all tools, equipment and personnel are clear before lowering load.
With suitable jack, raise vehicle clear of stands.
Carefully release stopper and allow ratchet to glide down to lowest position.
Carefully remove stands, then carefully lower vehicle with lifting device

WARRANTY NOTICE

This equipment is covered under a 1-year limited warranty when used as recommended. Only those items listed with a Part # are available for purchase. For assistance with the operation or the availability of replacement parts, contact our Parts and Warranty Department at www.torin- usa.com/support. Please have available a copy of your receipt, the model number of the product, serial number, and specific details regarding your question. Not all equipment components are available for replacement; illustrations provided are a convenient reference of location and position in the assembly sequence. The manufacturer reserves the rights to make design changes and or improvements to product lines and manuals without notice.