Shye West WD-300 Wireless Charge Clock Speaker User Guide

June 4, 2024
Shye West

West WD-300 Wireless Charge Clock Speaker
User Guide
Shye West WD-300 Wireless Charge Clock

Notice to User

  • Please make sure to use a fast charging plug to power the device. (Charging plug not included).

  • This device can only charge mobile phones that have a standard wireless charging function.

  • Wearing a metal phone case or a phone case that is too thick will block the wireless charging transmission. Please remove the phone case when wireless charging your mobile phone.

  • There may be signal interference and an increase in noise in FM radio mode when the wireless charge function is being used at the same time.

  • When using FM radio mode, please plug in the provided AUX cable to the AUX Jack on the device. The cable acts as an external antenna for radio reception. You can adjust the position of the cable to maximize the radio reception.

  • When the device is in clock mode, the  button will not function.
    Press the button to fully wake the device first then press the button to switch modes.

  • For safety reasons, the device’s wireless charging function may temporarily stop when overheating is detected during the wireless charging process.

  • lf you want to use Bluetooth and wireless charging at the same time, please make sure the device is fully turned on and switched to Bluetooth mode.

Safety Instructions

Please read the following instructions. Failure to follow all the instructions listed below may damage the device and/or may result in electric shock, fire, and/or personal injury.

  • Do not expose the device to direct sunlight
  • Do not remove screws from or open the device casing by yourself
  • To reduce the risk of fire or electric shock, do not expose this equipment to rain or moisture.
  • The unit shall not be exposed to dripping or splashing and objects filled with liquids, such as vases, shall not be placed on the unit.
  • Never charge the device with a damaged power cable.
  • Never put the device or charging cable near heat registers, radiators, stoves, or heaters.
  • Always put the device where it is not easily knocked over by persons in households or businesses.
  • Never touch the device with wet hands.
  • This device is only for the intended household or indoor use.
  • Never use any detergents to clean any part of the unit.

FCC STATEMENT

FCC ID: 2ASQY-WD-300
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user s encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help.

Welcome

We would like to congratulate you on the purchase of your WD-300 Wireless Charge Clock Speaker. Please read this manual carefully before use.

What’s Included

WD-300 deivce x1, USB Type-C charging cable x1, Aux Cable x1, User guide x 1

Overview

Shye West WD-300 Wireless Charge Clock - Figure

Button Functions

Shye West WD-300 Wireless Charge Clock - Figure 1

  1. Power Button: Press & Hold: On/Off Short Press after power on Clock Mode/ On

  2. Clock Button: Short Press: Set TimePress & Hold: Alarm On/Off Press Twice: Set Alarm

  3. Mode/Bass Button: Short press: Switch modes Press & Hold: Bass Adjust

  4. Next Button: Short press: Next Track(BT/TF Card mode)/Next Channel (FM Radio)/Add Hours/Minutes (Clock Mode)/Press & Hold: Reject an incoming call (Incoming  Call)Press & Hold 4 seconds: Disconnect devices(BT pairing mode)
    Alarm Dismiss (When the alarm buzzes)

  5. Previous Button: Short press: Previous Track(BT/TF Card mode)Previous Channel(FM Radio)/Minus Hours/Minutes (Clock Mode)/Alarm Dismiss (When alarm buzzes)

  6. Multi-Functional Knob: Turn Knob: Adjust volume/Adjust bass level (Bass adjust mode)/Adjust Hours/Minutes (Clock Mode)Short press: Play/Pause(BT/TF Card ode) Answer/End a call(Incoming Call)/Mute(FM Radio/Aux in mode)/Confirm Hours/Minutes (Clock Mode)/5 mins. SNOOZE(When the alarm buzzes)

Operation

• Charging the device
This device has a built-in rechargeable battery. To charge the device, use the provided USB Type-C Cable, connect the Type-C connector to the Type-C Input on the device, and the Standard USB-A Connector to a fast charging plug/Adaptor (Not Included)*. The red charging led indicator illuminates when charging and turns off when charging is complete.
Note: The wireless charge function requires a power connection to the charging plug.

Wireless Charge your mobile device
Connection to a fast charging plug is required to power the wireless charging function. The connection procedures are the same as how the device is connected for charging  Please see the steps above).  After the power is connected, place your mobile device on the circular silicone pad of the powered WD-300. Make sure your mobile device is centered according to the silicone pad for the best wireless charge efficiency. You may try to adjust the position of your mobile device if charging is not stable. The wireless charge ed indicator turns on when charging.
Note 1: Some phone cases may affect or block the wireless charging transmission, remove the case if necessary.
Note 2: The wireless charge-led indicator blinks if metals are detected indicating there is an abnormal situation. Remove any metals on the device to prevent overheating
Note 3: 10W/7.5W wireless charge output requires the device to be connected to a 9V-2A QC 3.0/PD fast charging plug. Connecting the device to a 5V-3A charging plug can only provide 5W wireless charging output. Using a nonqualified power plug may result in the malfunctioning of the device.
Note 4: The charging plug may not provide sufficient power if the wireless charging function, speaker function, and USB charge out function are all used at the same time. In such a situation, removing the USB connection is recommended.
Power On/Of & Switch modes
Press and hold the button to turn on the speaker. Short press the button to switch modes. Short press the button to enter clock mode. Short press the button in clock mode to switch on the device for other modes.
Bluetooth Pairing
Press the button repeatedly to enter Pairing mode. The word “BLUE” will start blinking on the speaker indicating that it is waiting for the device to pair. On your Bluetooth device, select “WD-300 / WD-300A” under your Bluetooth device list to pair. A successful connection via Bluetooth will be followed by an audible notification.  For help with Bluetooth Settings, please consult your device’s user manual.
Handsfree Speakerphone
The hands-free speakerphone function is enabled when the device is paired with your mobile device. Press the knob to answer an incoming call. To decline a call without answering, press and hold the knob during an incoming call. To end a call, press the knob during a call. For the best conversation experience, make sure the WD-300  unit is placed near (within 40cm) the user.
FM Radio
Press the   button repeatedly to enter FM radio mode. Press and hold the knob to initial automatic channel search. Searched channels will be saved automatically. Press the or button to switch channels. Short press the knob to mute the speaker when listening to the radio and short press the button again to unmute.
Note 1: When using FM Radio mode, please plug in the provided AUX cable to the AUX Jack on the device. The cable acts as an external antenna for radio reception. You can adjust the position of the cable for better radio reception.
Setting the alarm
Press the button twice quickly to set the alarm. Press the button or turn the knob to set the hour then press the knob to confirm. Now press the button or turn the knob to set the minute and press the knob to confirm. Once the alarm is set, a white dot next to the clock digits will appear indicating that an alarm has been set.
Snooze/Alarm Dismiss & Alarm On/Off
Press the Knob when the alarm buzzes to snooze for 5 minutes. Press any buttons (Except the On/Of button & the Snooze button) to dismiss the alarm when it buzzes. The alarm will still buzz the next day. To disable the alarm completely, press and hold the button until the white dot next to the clock digits disappears.
• Soothing Mode/ White noise mode
(Optional feature. Only available in WD-300A soothing mode version.) Press the button to switch to Soothing mode. Press the button to select soothing sounds. Press the knob to play/pause the soothing sound. Soothing sound/music will automatically stop if the speaker has not been operated for 30 mins.

Specifications

• BT version: V5.0 •Charging output: 5W/7.5W/10W
•Wireless Distance: 10m •Input voltage: 5V-3A / 9V-2A
•Speaker Power: 3W •Size: 195x105x72 mm
Speaker impedance: 40 •Battery Capacity: 1200mAh

We produce quality products with our heart for our customers. If you encounter any difficulty in using our product please feel free to contact us and we will sincerely serve every customer. Contact information can be found in online/at one store where you purchased this item.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur n a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  ser is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
    This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals