Topology DS103 3 5 Inch TFT and Remote BMZ Display User Guide
- June 3, 2024
- Topology
Table of Contents
DS103 3 5 Inch TFT and Remote BMZ Display
User Guide
Product Details
Product Name
Intelligent LCD display, model: DS103
Firmware: CYCMotor Ltd specific
Features
- Simple and lightweight, separate installation bracket design
- High brightness, high contrast 3.5 inches colored TFT screen
- Clock function (clock is on when the display shutdown)
- Excellent outdoor design with IP65-level waterproof
- Micro USB serial communication port, convenient maintenance services.
Dimensions & Materials
Materials
Product shell – ABS + PC plastic
Transparent window – Tempered glass
Dimensions
L 110mm x W 68.2mm x H 68mm
Electrical Specifications
- Power supply: DC 24V/36V/48V/ 52V
- Rated current: 30ma/36V
- Shutdown leakage current: <1uA
- Screen specification: 3.5” colored TFT（480*320pixels）
- Communication method: UART (default)
- Operating temperature: -20°C ~ 60°C
- Storage temperature: -30°C ~ 80°C
- Waterproof level: IP65
Quick start guide
After unboxing and installing your CYC motor system, there are two main things you need to set up.
- Change your Battery No. setting according to your rated voltage.
Within 15 seconds of turning on your display, long press the MENU button to enter the settings functions. Press UP/ DOWN to navigate to the settings page & MENU to select.
6s = 22.2V
7s = 25.9V
8s = 29.6V| 9s = 33.3V
10s = 36V
11s = 40.7V| 12s = 44.4V
13s = 48V
14s = 52V
---|---|---
*Please note that 6s to 9s are not compatible with the CYC systems. This will be removed in future batches. Our apologies for the confusion.
-
Change your Wheel setting according to your bike’s wheel size.
-
Now, you can set things up like your temperature and speed unit as well as your brightness level. Otherwise, you’re good to go!
Functionalities
Power On/ Off
Press and hold the POWER button for 3 seconds to turn the display on/ off.
Navigation
The MENU button is used to go into your main settings page & your clear data
page. It is also used to enter and select a setting or function.
- POWER
- MENU
- UP
- DOWN
Switch Dashboard
Switch the main dashboard to display different information by pressing the
MENU button.
Assist Level Operating
Press the UP/ DOWN button to change the assist level between levels 1, 2, and
3. Note that “OFF” means no motor assistance will be given.
Dark & Light-Themed Dashboard
Long press the UP button to switch between light and dark-themed dashboards.
Walk Assist
Hold the DOWN button to activate the walk assist. Note that it takes 3
seconds to activate & will deactivate immediately when the button is released.
Settings
Long press the MENU button within 15 seconds of switching on the display to
enter the “Settings” page. Note that once the system has been activated for
longer than 15 seconds, you will need to restart the motor system to enter the
settings menu.
Clean Trip Data
Wait 15 seconds after starting up the motor system to enter the “Clean Data”
menu. Long press the MENU button to clear the previous trip data. Please note
that the trip data does not automatically clear once you restart the motor
system. This is a manual process.
Error Codes
In certain circumstances, an error code may appear on your display. Contact
technical_support@cycmotor.com for
assistance.
*Error codes TBC
Installation
- Determine if you need to select the corresponding mounting clamp and rubber clip ring according to the diameter of your handlebar (Applicable handlebar specifications：Φ 22.2; Φ25.4; Φ31.8).
- Open the display lock clamp and insert the rubber clip (if applicable) into the correct position of the lock clamp.
- Set the rubber ring in the bracket (if applicable) then assemble it in the middle of the handlebar. You can adjust the angle of the display to make the display screen more visible when riding. After fixing the angle, tighten the screws. The tightening torque is 1N.m.
- Open the lock ring of the switch and set it in the appropriate position on the left side of the handlebar. Adjust the angle and position of the switch as needed in order to ensure that you can operate the switch easily.
- Fix and tighten the handlebar fixing screw with an M3Hex wrench (locking torque is 0.8Nm).
- Connect the display connector to the controller connector according to the label.
Note: Damage caused by excessive torque is not covered by the warranty.
Compatibility
The clamps are suitable for 3x different handlebar sizes: 31.8mm, 25.4mm, and
22.2mm.
Pin Layout
- Red wire: Anode(36V to 72V)
- Black wire: GND
- Yellow wire: TxD (display -> controller)
- Green wire: RxD (controller -> display)
- Blue wire: Power cord to the controller
Certification
CE / IP65 (waterproof) / ROHS.
Be sure to contact technical_support@cycmotor.com if further assistance is
needed.
THANK YOU!
The information contained in this document is derived from the TFT LCD
Display Guide provided by Zhejiang Topology Intelligent Technology Co., Ltd.
(otherwise known as Topology). All the information contained in this manual is
published in good faith and for general information purposes only. Contact
technical_support@cycmotor.com for further
assistance.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>