2013 FORTE KOUP G 2.0 DOHC Manual Transaxle System Instructions

2013 FORTE KOUP G 2.0 DOHC Manual Transaxle System

Removal

1. Remove the following items;

   • Engine cover (A). (Refer to “Intake and Exhaust system” in EM group.)
   • Air cleaner assembly (B) and air duct (C) . (Refer to “Intake and Exhaust system” in EM group.)
   • Battery and battery tray (D). (Refer to “Charging system” in EE group.)
   • ECM (E) (Refer to “Engine Control System” in FL group.)

2. Disconnect the back up lamp switch connector (B) and the vehicle speed sensor connector (A).

3. Remove the ground cable from transaxle (A).

4. Disconnect the select or shift cable assembly (B) after removing the pin (A).

5. Remove the tube bracket bolt (A).
   Tightening torque:
   14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.8 ~ 15.9 lb-ft)

6. Remove the transaxle upper mounting bolt (B-2ea) and the start motor mounting bolt (A-2ea).
   Tightening torque:
   [A,B] 42.2 ~ 54.0 N.m (4.3 ~ 5.5 kgf.m,31.1 ~ 39.8 lb-ft)

7. Using the SST (09200-38001), hold the engine and transaxle assembly safely.

8. Remove the transaxle support mounting bracket bolts (A-4ea).
   Tightening torque:
   58.9 ~ 78.5 N.m (6.0 ~ 8.0 kgf.m, 43.4 ~ 57.9 lb-ft)

9. 9. Remove the under cover (A).
   Tightening torque:
   9.8 ~ 11.7 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.6 lb-ft)

10. Remove the side cover (A).

11. Remove the following items. (Refer to ” Drive shaft assembly ” in DS group.)

12. Drive shaft assembly. (Refer to “Drive shaft assembly ” in DS group.)

13. Sub frame assembly. (Refer to “Front suspension system” in SS group.)

14. Remove the clutch release cylinder assembly(B) after removing the nuts (A-2ea).
    Tightening torque:
    14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.8 ~ 15.9 lb-ft)

15.  Remove the drive shaft cover (A).

16. Remove the mounting bolts(A-4ea, B-2ea) of lower part of the transaxle, and the left side cover and remove the transaxle assembly by supporting it with a jack.
    CAUTION
    Be careful not to damage other system or parts near by when removing the engine and transaxle assembly.
    Tightening torque:

17.  43 ~ 49 N.m (4.3 ~ 4.9 kgf.m, 31.1 ~ 35.4 lb-ft)

18.  43 ~ 55 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)

Installation

1. Installation is the reverse of removal. NOTE

• Adding Manual transaxle fluid. (Refer to “Manual transaxle system” in this group.)
  Portions of materials contained herein are sourced from the Hyundai Kia Automotive Group Copyright 2011 – 2015 Service Repair Solutions, Inc.

References

• Direct-Hit -- Your Session has been Terminated

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>