TOPRCBOXS S1 Drone User Manual
- June 4, 2024
- TOPRCBOXS
Table of Contents
TOPRCBOXS S1 Drone
DISCLAIMER & SAFETY GUIDELINES
Please read the disclaimer carefully before using this product. By using it,
you hereby agree to this disclaimer and signify that you have read them fully.
-
FLIGHT ENVIRONMENT:
-
DO NOT fly above or near obstacles, crowds, cars, open water, public road, high voltage power lines, trees or airport.
-
DO NOT fly the drone in the magnetic interference area ,radio interference area, and government regulated no-fly zones.
-
DO NOT use this product in severe environments such as rain, snow, fog and windy, etc.
-
Please always stay away from the rotating propellers and motors.
-
Always keep small parts and electrical parts out of the reach of children.
-
The charger is not a toy. Only use the original charger provided.
-
Battery charging should be done in a location out of reach of children. When citrating it must be kept away from flammable materials such as bed, carpet ,wood floors etc.,
-
DO NOT reverse polarity or puncture batteries. DO NOT store the batteries near any heat source.
-
Dispose of the drone and batteries in accordance with local regulations. DO NOT treat it as household waste.
TOPRCBOXS accepts no liability for damage, injury or any legal responsibility
incurred directly or indirectly from the use of this product.
The user shall observe safe and lawful practices including, but not limited
to, those set forth in these Safety Guidelines.
TOPRCBOXS reserves the right to update this user manual.
MAINTENANCE AND CARE
- Check thoroughly (take note the propellers) every time after a crash or violent impact.
- Before the first fly, learn how to apply the “Emergency Stop” function, which is in page 11 of this manual.
- Do not charge the battery if it is hot. Let it cool down first.
- If you do not plan to use your drone for an extended period of time, remove the batteries from the controller to avoid battery leakage, which may damage the controller.
- Keep the drone and the controller in a location where is cool and dry, and avoid long time exposure to direct sunlight.
- Please give your drone a minute cool down time after each flight, to increase the durability of the drone.
Specifications
- Max Flight Distance: 330 feet/ 100m (outdoors and unobstructed)
- Transmission Distance: About 196feet/60m( outdoors and unobstructed)
- Flight Time: About 15 mins
- Charging Time: About 80 mins
- Mobile APP Requirement: Android 5.1 and later, IOS 9.0 and later
Package contents
Video Tutorial
Please download the APP “Sl FPV” or scan the code to watch our S1 drone
tutorial video.
Please do not hesitate to contact us if you need further support.
Drone Diagram
Controller Details & Charging the Controller
Important Note:
- When the remote controller continuously emits the sound of DI..DI..DI~, and the indicator lights on the controller blink continuously it may a alarm showing it is running out of battery, please replace the battery of the remote controller.
- Plug the USB charging cable into a USB charging port on the computer, power bank or USB adapter (SV/0.S-2A).
- Please always use the usb cables provided.
- Charging Time of the Controller (Full Charge): about 45 mins.
Phone Holden
Insert
Insert the phone holder, a click sound will be heard ****
Trimmer
Press the Trimmer button to enter the Trimmer mode.(it will emit a beep sound)
Now you can push the right joystick to re-balance the drone.
Pressing the Trimmer button again to exit the Trimmer mode. (it will emit a
beep sound)
“Trimmer mode” needs to be turned off to regain control of the drone
F/B Sideways Drift Trim: If the drone tends to drift forward, press the Trimmer button to enter and push the right joystick down to re-balance the drone .If the drone tends to drift backwards ,press the Trimmer button to enter and push the right joystick up to re-balance the drone. Press the Trimmer button again to exit the mode (It will only trim a bit when press once. Press more times to adjust until the drone stays oriented at the control)
L/R Sideward Fly Trim: If the drone tends to drift left, press the Trimmer button to enter and push the right joystick right to re-balance the drone. If the drone tends to drift right ,press the Trimmer button and push the right joystick left to re-balance the drone. Press the Trimmer button again to exit the mode (It will only trim a bit when press once. Press more times to adjust until the drone stays oriented at the control.)
Charge the Drone Battery
Important Note:
-
When the drone battery runs low. the indicator lights on the drone will blink continuously and the controller will emit “DI DI DI~”.
At this time the drone will land automatically after about 60 seconds. -
Plug the USB charging cable into a USB charging port on the computer, power bank or USB adapter (5V/0.5-2A).
-
Please always use the usb cables provided.
-
Charging: red light turn on
-
Charge Complete: green light turn on.
-
Charging Time (Full Charge): about 80 mins.
-
Flight Time: About 15 mins.
Unfold the Drone
- Unfold the front arms, then the rear arms.
Propeller Guard Installation
- Remove the small plastic chip from the rotor shell.
- Insert the propeller guard into the rotor shell
Propeller Replace Guide
- Loosen the screw to remove the propeller.
- Fit the spare propeller into the drone.
- Tighten the screws.
IMPORTANT NOTE: Every propeller has indicated alphabet A and B.
Please install the propellers in correspondence with propeller A and propeller
B as shown above. Otherwise the drone will fail to take off.
Tip: If the drone flying not stable after crashed or dropped. Please
replace all damaged propellers.
Flight Instruction
Important note: For beginners, we would recommend the tail of the drone
to face towards the pilot, so can better recognize the flight orientation and
make operation easier.
Ascend: Push up the left joystick Forward: Push up the right joystick
Descend: Pull down the left joystick Backward: Pull down the right
joystick
- Turn Right: Push the left joystick to the right
- Turn Left: Push the left joystick to the left
- Sideways Fly to the Right: Push the right joystick to the right
- Fly to the Left: Push the right joystick to the left
Battery Installation – Drone
Install the battery into the drone after it’s fully charged. Please push the
battery to the end. Long press the ON /OFF button to start.
Note: You may refer to our tutorial video for reference. Linking
Controller with the Drone
- Turn on the drone first, then place it on a flat surface with the head forward. (the LEDs on the drone flash).
- Turning on the controller. The controller will emit “DI DI” sound when turning on. The LED of the drone will go from flashing to solid, indicating that the controller and the drone is now paird.
Important Note:
- Please make sure that the drone is placed on leveled surface otherwise it will fail to pair with the controller.
- Please ensure the power of the drone has been turned on before turning on the controller. Otherwise it cannot be paired successfully.
- If the drone keep blinking and fail to take off after powering on the controller, it means it’s under low battery. Please charge it.
- If fails to pair, please turn off the drone and the controller, and repeat steps.
Calibrating the Drone
Press the calibration button and the indicator on the drone will start
flashing.
Wait until the indicator stops flashing. It is now completed.
Note: If the drone flying not stable, Please land the drone on level
surface and calibrate it.
Calibration
One Key Auto Take-off/ Land
TAKE OFF: After the linking and calibration,
Press this button and the drone will start taking off and hovering in the air.
LAND: While in the air, press the same button and the drone will land
automatically.
Note: Press the One Key Take-off button, the drone /landing will fly up
and hover at about 1.5 meters height.
Please place the drone on the flat surface with enough climbing space before
taking off.
Emergency Stop
In an event of an emergency where the drone needs to be stopped immediately,
LONG PRESS the button and the drone will stop immediately.
Note: When using Emergency Stop function, it will cause the drone in the
air to fall from the sky.
Mode of High/Medium/Low Speed
By default, the drone is set at low speed level. To speed up, dial the wheel
right and it will emit “beep beep” sound, indicating it is at medium speed
level. Dial the wheel right again and it will emit “beep beep beep” – High
Speed Level. Altitude Hold Function
The drone is designed with altitude-hold function so the drone can maintain
its altitude after you release the left joystick. (The left joystick will
automatically spring back to the middle)
Circle Fly
Circle Fly: During the flight, press the circle fly button, the controller
will make a “DI” sound which indicates that the drone enters the circle
fly. This drone will exit the circle fly function automatically 10 seconds
after, and you can also push the direction joystick to any direction to exit
the circle fly.
Note: When the LED on the drone keep flashing, it means the drone is
under low battery mode. Circle Fly will NOT be performed by the drone.
Headless Mode
Prerequisite: Before entering the Headless Mode, the drone is required to be
calibrated.
- Place the drone on a flat level surface, let the head of the drone face forwards, and the tail of the drone face towards the pilot, then calibrate the drone.
- Press the Headless Mode button, the light of the drone will start flashing, meaning the drone is entering into Headless Mode.
- Now you should be able to operate your drone under Headless Mode.
To exit, press the Headless Mode button again, it will emit a beep sound, showing it has been exited.
Important Note: When calibrating the drone, ensure the head of the
drone is facing forward, and tail is facing towards the pilot. This can help
you better understand the headless mode. Because Headless Mode is set
according to the direction of the drone while calibrating. Under Headless
Mode, if the direction of the drone is inaccurate, please land it and repeat
step 1 and 2 to start again.
Download APP and Connect
to WIFI
- Please search “S1 drone” or scan the QR code to download the APP. Sl_DRONE-WIFI-*”
- Go to the WIFI setting of your smart phone and connect to the WIFI “Sl_DRONE-WIFI-****”
- Launch the “S1 drone” APP and tap “start”.
Important Note:
-
Please make sure that “Sl_DRONE-WIFI-****” WIFI is only connected to one smart phone.
-
If you fails to see the First Person View(FPV) after clicking “start” in the APP, it may because the app has been shielded by the smart phone.
Please find the solutions as below: -
Check “S1 drone” APP setting, make sure “WLAN &. Cellular Data” has been selected.
-
Go to phone setting – turn off WI-FI – Turn on “Cellular Data” – Open the APP – A window will pop up – select “YES”
-
Re-install the APP.
-
Use another smart phone (ios/android).
APP Operation Panel
- Take Photo
- Calibration
- Voice Control
- Record Video
- Special Effects
- Mode
- Media Gallery
- Flip image
- Take Off
- ON/OFF
- More
- Landing
- Unlock/Lock
- Gravity Sensor
- STOP Emergency
- Speed Switch
- Gesture Control
- Stop
- Headless Mode
- Trajectory Flight
How to control the drone with the APP Instead of remote controller?
Tum on the drone – Connect WIFI S 1DRONE-WIFI-****” – Open the APP and click
start click icon (icon TU light up) – Click icon to start the flight..
-
Click icon (Trajectory Flight) to direct your drone’s flight path by simply draw a flight route on the screen.
-
Click icon (Voice Control): fly, land, left ,right, forward ,backwards.(only support English)
-
Click icon (Gravity Sensor) to control your drone’s flight path by shifting your phone.
For example: shift your phone leftwards, the drone will fly towards the left side immediately. -
Click e icon (Gesture Control) and make specific gesture within the sight range of camera, the drone will execute commands of taking photo /video. take photo record video (repeat the same action to stop noting).
TROUBLESHOOTING
Problems Reasons Solutions
The light on the drone are flashing and the drone is not responding.|
Insufficient battery power.
Controller is NOT connected to the drone.|
- Fully charge the battery
- Turn off the drone and controller. Reconnect them by turning on the drone first then the controller.
---|---|---
| Unbalanced position.| Place the drone on a horizontal flat surface and
reconnect them.
| Insufficient battery power.| Fully charge the battery.
The propellers spin but doesn’t take off.| Propellers NOT installed
correctly.| Check the propellers installation (A to A,B to BJ
| | Replace new propellers.
| Damage propellers.|
| Something being caught in the propellers or gears.| Clear gears and
propellers.
| Propellers NOT installed correctly;| Check the propellers installation (A to
A,B to BJ
The drone doesn’t fly properly after a crash| Damaged propellers;
The balance of gyro is confused;|
- Replace new propellers.
- Calibrate the drone or press trim button to fine tune the direction.
| Propellers have hit the Blade Guard.| Make sure blades work well.
| | Replace motors.
Contact Us
TOPRCBOXS Is committed to leave all our customers best products and services.
we value each or our customers and appreciate your
suggestions and opinions, Please feel free to contact us:
support_us@toprcboxs.com (US region)
support_eu@toprcbaxs.com (UK region)
For online support, plea5e 5c:an this code with Live Chat.
FCC Compliance
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by ne or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CAUTION Risk of explosion if battery is replaced by all incorrect type. Dispose of used batteries according to the instructions.
The symbol indicates DC voltage
Recycling
This product bears the selective sorting symbol for waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY CE
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>