Turnils AMP28B DC Tubular Motor User Manual

Turnils AMP28B DC Tubular Motor User Manual

1 . Pair / Unpair Remote Control

a. Press “P1” button (about 2 sec) on the motor head until motor jog x1 and beep x1.
b. In the next 1 O secs, press and hold “Stop” button on the remote control until motor jog x2 and beep x3.
• Repeat the same procedure to unpair remote control.

2. Change Motor Direction (1f necessary)

Press “Up” or “Down” button to check if the shade moves in the desired direction.

If you need to reverse the direction, press and hold (about 2 sec) “Up” and “Down” buttons simultaneously until motor jog x1 and beep x1 .

• The operation is only valid when there are no limits. If the motor has already set the upper and lower limit, then you can only
  switch direction by pressing P1 button (See P1 button instructions).

3. Setting the Upper and Lower Limits

3.1  Set Upper Limit

a. Press “Up” button to raise the shade, then press “Stop” button when it is in the desired upper limit.
b. Press and hold (about 2 sec) “Up” and “Stop” buttons simultaneously until motor jog x2 and beep x3.

3.2 Set Lower Limit

a. Press “Down” button to lower the shade, then press “Stop” button when it is in the desired lower limit.
b. Press and hold (about 2 sec)”Down” and “Stop” buttons simultaneously until motor jog x2 and beep x3.

If you exit the limit setting status before you finish the limit settings, the motor will take the previous existing limits.

Factory Mode Complete User Mode Begins

4. Adjust Limits

4.1 Adjust the Upper Limit

a. Press and hold (about 5 sec) “Up” and “Stop” buttons simultaneously until motor jog x1 and beep x1 .
b. Use “Up” button to raise the shade to the desired highest passion, and use “Up” or “Down” button to do the final adjustment if necessal’f.
c. Press and hold (about 2 sec) “Up” and “Stop” buttons simultaneously until motor jog x2 and beep x3.

4.2 Adjust the Lower Limit

a. Press and hold (about 5 sec) “Down” and “Stop” buttons simultaneously until motor jog x1 and beep x1 .
b. Use “Down” button to lower the shade to the desired lowest passion, and use “Up” or “Down” button to do the final adjustment if necessal’f.
c. Press and hold (about 2 sec) “Down” and “Stop” buttons simultaneously until motor jog x2 and beep x3.

5. Favorite Position

5.1 Set Favorite Position

a. Use 11Up” or “Down” button to move the shade to desired Favorite position.
b. Press one “P2” button on the back of remote control until motor jog x1 and beep x1.
c. Press and hold (about 2 sec) “Stop” button until motor jog x7 and beep x7 .
d. Once more, press and hold (about 2 sec) “Stop” button until motor jog x2 and beep x3.

5.2 Send Shade to Favorite Position

Press and hold (about 2 sec) “Stop” button, motor will move to Favorite position.

5.3 Delete Favorite Position

a. Press one “P2” button until motor jog and beep x1.
b. Press and hold (about 2 sec) “Stop” button until motor jog and beep x1 .
c. Once more, press and hold (about 2 sec) “Stop” button until motor jog x1 and long beep x1 .

6. Roller Mode and Sheer Mode

6.1 Roller Shade Mode – continue movement after a short press -Default

Mode

a. Press and hold (about 5 sec) “Up” and “Down” buttons simultaneously until motor jog x1 .
b. Press and hold (about 2 sec) “Stop” button until motor jog x2 and beep x3.

6.2 Sheer Shade Mode – jog movement after a short press (continue

movement after a long press)

a. Press and hold (about 5 sec) “Up” and “Down” buttons simultaneously until motor jog x1 .
b. Press and hold (about 2 sec) “Stop” button until motor jog x1 and beep x1 .

7. Add or Remove Additional Remote

7.1 Using Current Remote Control

a. On the current remote control, press one “P2” button until motor jog x1 and beep x1.
b. Once more, on the current remote control, press one “P2” button until motor jog x1 and beep x1 .
c. On the New remote control, press one “P2” button until motor jog x2 and beep x3.

• Repeat the same procedure to remove additional remote control.

7.2 New Remote Control

Follow instructions under the section 1.
Pair / Unpair Remote Control

8. Adjust Motor Speed

8.1 Acceleration Speed

a. Press one “P2” button until motor jog x1 and beep x1 .
b. Press “Up” button until motor jog x1 and beep x1.
c. Once more, press “Up” button until motor jog x2 and beep x1 .

8.2 Deceleration Speed

a. Press one “P2” button until motor jog x1 and beep x1 .
b. Press “Down” button until motor jog x1 and beep x1.
c. Once more, press “Down” button until motor jog x2 and beep x1 .

• If the motor has no response, it already has a Maximum or Minimum speed.

Fields of Application

Specif1cat1ons

Working temperature: -10° C – +50″ C
Input Voltage: USB 5V 1 A / USB 5V 2A
Radio Frequency: 433.925 MHz
Maximum Running Time: 6 minutes

The motor is suitable for motorization of roller shades, sheer shades, roman shades, and revolve shades.

Attention

Never drop, knock, drill or submerge the motor. Keep the power cable in the proper position as shown below.
Read all safety instructions before installation.
incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.

Safety Instructions

1. Do not expose motor to humid, damp, or extreme temperature conditions.
2. Do not drill into motor.
3. Do not cut the antenna. Keep it clear from metal objects.
4. Do not allow children to play with this device.
5. If the power cable or connector is damaged, do not use.
6. Ensure the correct crown and drive adaptor are used.
7. Ensure the power cable and aerial is clear and protected from moving parts.
8. Gable routed through walls should be property isolated.
9. Motor is to be mounted in horizontal position only.
10. Before installation, remove unnecessary cards and disable equipment not needed for powered operation.
11. Installation and programming should be performed by a qualified professional. Use or modification outside the scope of these instructions may void warranty.

Charging Instructions

This motor has a built in Li-ion battery pack with integrated charge management.
Max pcwer input for recharging: 5V 2A.
Before first use please charge motor for 6 hours using a 5V charger.
During operation, when the motor starts, the buyer will beep 10 times, indicating a low-voltage alarm and needs to be charged.
During operation, if the voltage is detected to be too low, the battery stops running and needs to be recharged.

Rechargeable Battery

P1 Button Instructions

Button Instructions

Declarations

U.S. Radio Frequency FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to 1he following 1Wo condi1ions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Any Changes or modifications expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC RF Radlatlon Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be Installed and operated with minimum distance 20cm be1Ween the radiator & your body.

ISEO RSS Warning:
This device complies with Innovation, Science and Economic Development Ganada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

IC Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

This Class B digital apparatus complies with Canadian ICES-003.
CAN ICES-003 (B)/NMB-003(8)

Quick Index

Troubleshooting

Do not dispose of In general waste.
Please recycle batteries and damaged electr1cal products appropriately.

Please scan QR code to see more AMPTM product information

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>