Turnils North America AMP25BDC DC Tubular Motor for Narrow Shades Instruction Manual

North America AMP25BDC DC
Tubular Motor for Narrow Shades
Instruction Manual

Fields of Application

Specifications

Working temperature: -10º C ~ +50º C
Input Voltage: USB 5V 1A / USB 5V 2A
Radio Frequency: 433.925 MHz
Maximum Running Time: 6 minutes
The motor is suitable for the motorization of roller shades, sheer shades, roman shades, and revolve shades.

Model| Rated Torque (N.m)| Rated Speed (RPM)| Rated Power (W)
---|---|---|---
25BDC – 1.1/28| 1.1| 28| 12

Attention

Never drop, knock, drill or submerge the motor. Keep the power cable in the proper position as shown below.
Read all safety instructions before installation.
Incorrect installation can lead to serious injury and will void the manufacturer’s liability and warranty.

Safety Instructions

1. Do not expose the motor to humid, damp, or extreme temperature conditions.
2. Do not drill into the motor.
3. Do not cut the antenna. Keep it clear from metal objects.
4. Do not allow children to play with this device.
5. If the power cable or connector is damaged, do not use it.
6. Ensure the correct crown and drive adaptor are used.
7. Ensure the power cable and aerial is clear and protected from moving parts.
8. Cable routed through walls should be properly isolated.
9. The motor is to be mounted in a horizontal position only.
10. Before installation, remove unnecessary cords and disable equipment not needed for powered operation.
11. Installation and programming should be performed by a qualified professional. Use or modification outside the scope of these instructions may void the warranty.

Charging Instructions

This motor connects with an external Li-ion battery pack with integrated charge management.
Max power input for recharging: 5V 2A.
Before first use please charge the motor for 6 hours using a 5V charger.
During operation, if the voltage is detected to be too low, the battery stops running and needs to be recharged.

Rechargeable Battery

P1 Button Instructions

Test Motor Activate Pairing Mode Sleep Mode Reverse Direction Reset To Factory Settings

Button Instructions

Essential Settings
The steps in factory mode must be completed to ensure proper operation.
1. Pair / Unpair Remote Control

a. Press the “P1” button (about 2 sec) on the motorhead until the motor jog x1 and beeps x1.
b. In the next 10 secs, press and hold the “Stop” button on the remote control until the motor jog x2 and beeps x3.

• Repeat the same procedure to unpair the remote control.
  2. Change Motor Direction (if necessary) Press the “Up” or “Down” button to check if the shade moves in the desired direction. If you need to reverse the direction, press and hold (about 2 sec) the “Up” and “Down” buttons simultaneously until the motor jog x1 and beeps x1.
  *The operation is only valid when there are no limits. If the motor has already set the upper and lower limit, then you can only switch directions by pressing the P1 button (See P1 button instructions).
  3. Setting the Upper and Lower Limits

a. Press the “Up” button to raise the shade, then press the “Stop” button when it is in the desired upper limit.
b. Press and hold (about 5 sec) the “Up” and “Stop” buttons simultaneously until the motor jog x2 and beeps x3.
3.2 Set Lower Limit
a. Press the “Down” button to lower the shade, then press the “Stop” button when it is in the desired lower limit.
b. Press and hold (about 5 sec) “Down” and “Stop” buttons simultaneously until motor jog x2 and beep x3.
*If you exit the limit setting status before you finish the limit settings, the motor will take the previous existing limits.

Adjust Limits

4.1 Adjust the Upper Limit

a. Press and hold (about 5 sec) the “Up” and “Stop” buttons simultaneously until the motor jog x1 and beeps x1.
b. Use the “Up” button to raise the shade to the desired highest position, and use the “Up” or “Down” button to do the final adjustment if necessary.
c. Press and hold (about 5 sec) the “Up” and “Stop” buttons simultaneously until the motor jog x2 and beeps x3.

4.2 Adjust the Lower Limit

a. Press and hold (about 5 sec) “Down” and “Stop” buttons simultaneously until motor jog x1 and beep x1.
b. Use the “Down” button to lower the shade to the desired lowest position, and use the “Up” or “Down” button to do the final adjustment if necessary.
c. Press and hold (about 5 sec) the “Down” and “Stop” buttons simultaneously until the motor jog x2 and beeps x3.

Favorite Position

5.1 Set Favorite Position

Use the “Up” or “Down” button to move the shade to desired Favorite position. Press one “P2” button on the back of the remote control until the motor jog x1 and beeps x1.
Press and hold (about 2 sec) the “Stop” button until the motor jog x1 and beeps x1. Once more, press and hold (about 2 sec) the “Stop” button until the motor jog x2 and beeps x3.
5.2 Send Shade to Favorite Position

Press and hold (about 2 sec) the “Stop” button, the motor will move to the Favorite position.
5.3 Delete Favorite Position

Press one “P2” button until the motor jog and beeps x1.
Press and hold (about 2 sec) the “Stop” button until the motor jog and beeps x1.
Once more, press and hold (about 2 sec) the “Stop” button until the motor jog x1 and long beep x1.

Roller Mode and Sheer Mode

6.1 Roller Shade Mode – continue movement after a short press – Default Mode

a. Press and hold (about 5 sec) “Up” and  “Down” buttons simultaneously until motor jog x1.
b. Press and hold (about 2 sec) the “Stop” button until the motor jog x2 and beeps x3.
6.2 Sheer Shade Mode – jog movement after a short press (continue movement after a long press)

a. Press and hold (about 5 sec) the “Up” and “Down” buttons simultaneously until the motor jog x1.
b. Press and hold (about 2 sec) the “Stop” button until the motor jog x1 and beeps x1.

Add or Remove Additional Remote

7.1 Using Current Remote Control

a. On the current remote control, press and hold (about 2 sec) one “P2” button until the motor jog x1 and beeps x1.
b. Once more, on the current remote control, press and hold (about 2 sec) one “P2” button until the motor jog x1 and beeps x1.
c. On the New remote control, press and hold (about 2 sec) one “P2” button until the motor jog x2 and beeps x3.
*Repeat the same procedure to remove the additional remote control.
7.2 New Remote Control
Follow instructions under section 1. Pair / Unpair Remote Control

Adjust Motor Speed

8.1 Acceleration Speed

a. Press one “P2” button until the motor jog x1 and beeps x1.
b. Press the “Up” button until the motor jog x1 and beeps x1.
c. Once more, press the “Up” button until the motor jog x2 and beeps x1.
8.2 Deceleration Speed

a. Press one “P2” button until the motor jog x1 and beeps x1.
b. Press the “Down” button until the motor jog x1 and beeps x1.
c. Once more, press the “Down” button until the motor jog x2 and beeps x1.
*If the motor has no response, it already has a Maximum or Minimum speed.

Declarations

U.S. Radio Frequency FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
ISED RSS Warning:
This device complies with Innovation, Science, and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Quick Index

(hold down for 2s)
Lower Limit: Down (hold down for 2s) > Down + Stop (hold down for 2s)
Add / Remove Favorite Position| P2 > Stop > Stop
Roller Mode & Sheer Mode Switch| Up + Down (hold down for 5s) > Stop
Adjust Limits| Upper Limit: Up + Stop (hold down for 5s) > Up or Down > Up + Stop (hold down for 2s)
Lower Limit: Down + Stop (hold down for 5s) > Up or Down > Down + Stop (hold down for 2s)
Pair / Unpair Additional Emitter| P2 (existing) > P2 (existing) > P2 (new)
Speed Regulation| Acceleration: P2 > Up > Up
Deceleration: P2 > Down > Down

Troubleshooting

Issues

| Possible Causes|

Solution

---|---|---
The motor is not responding| External battery pack is depleted| Recharge with compatible AC adaptor and check connection and positioning of solar PV panel
Insufficient charging from Solar PV Panel| Check connection and orientation of solar PV panel
The remote control battery is discharged| Replace battery
The battery is inserted incorrectly into the remote control| Check battery polarity
Radio interference/shielding| Ensure the remote control and the antenna on the motor are positioned away from metal objects
The receiver is far away from Remote Control| Move remote control to a closer position
Power failure| Check the power supply to the motor is connected and active
Incorrect wiring| Check that wiring is connected correctly (refer to motor installation instructions)
Motor beeps 10 times when in use| Battery voltage is low / PV (solar
panel issue)| Recharge with AC adapter or check connection and positioning of solar PV panel
Cannot program a single motor
(multiple motors respond)|

Multiple motors are paired to the
same channel.

| Always reserve an individual channel for programming functions
SYSTEM BEST PRACTICE – Provide an extra 15 channel remote in your multi-motor projects that provide individual control for each motor for programming purposes
Place all other motors into sleep mode (ref to P1 button instructions)

Please scan the QR code to see more AMP™ product information
Do not dispose of the general waste.
Please recycle batteries and damaged electrical products appropriately

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>