RUBI 05973 Universal Ceramic Hard And Duro Multi Purpose Instruction Manual
- June 4, 2024
- RUBI
Table of Contents
RUBI 05973 Universal Ceramic Hard And Duro Multi Purpose
Product Information
- Specifications:
- Product Name: UNIVERSAL CERAMIC HARD & DURO MULTI-PURPOSE PORCELANIC ABRASIVE MARBLE RESCUE
- Manufacturer: GERMANS BOADA SA / RUBI UK LTD
- Address: Units 16 & 17, Easter Park Ferry Lane, Rainham, Essex PM13 9BP – UNITED KINGDOM
- Contact P. 44 (0) 1708559609,
- F. 44 (0) 1708553813,
- E-mail: rubiuk@rubi.com
- Website: www.rubi.com.
- Precautions
- Before using the product, ensure to read and understand all safety precautions mentioned on the label.
- Mounting
- During mounting, make sure the direction indicated on the disk is followed for proper alignment.
- Secure Attachment
- Ensure the disk is securely attached before operation, avoiding any sudden movements or increasing the diameter of the cut.
- Proper Alignment
- Check that the alignment of the disk is correct before starting the cutting operation. Assemble the components correctly.
- Working Conditions
- Use appropriate safety gear while working with the disk to prevent accidents. Ensure there are no vibrations, deformations, or slippages.
- Symbols on Disk
- Refer to the symbols on the disk for guidance on its usage and safety precautions.
- Test Run
- Before actual cutting, perform a test run to ensure the cutting ability is sufficient and uninterrupted.
- Cutting Technique
- To reduce speed and achieve precision, avoid pressing too hard on the disk or making sudden movements. Verify that the cutting depth is adequate.
- Disk Maintenance
- If you notice a decrease in cutting performance, consider using a RUBI ceramic blade for replacement to maintain optimal cutting efficiency.
FAQs
- Q: How do I know when to replace the disk?
- A: If you experience reduced cutting ability despite no visible damage, consider replacing the disk with a RUBI ceramic blade for continued efficiency.
- Q: Can the disk be used on wet surfaces?
- A: For optimal performance, ensure the disk is used on dry surfaces to maintain cutting effectiveness and safety.
- Q: What should I do if the disk overheats during operation?
- A: Stop operation immediately and allow the disk to cool down before resuming work to prevent overheating-related issues.
PRODUCT USING INSTRUCTION
- Carefully read the instructions.
- Use the appropriate blade according to the material that needs to be cut. Check the reference on the blade’s sticker. (1-A)
- Follow the maximum rpm limits stated in the blade. Do not exceed them. (1-B)
- Do not use damaged or bent blades or units that might have been damaged after a fall. (1-C)
- Make sure that the blade is set up to rotate in the direction indicated in the machine. (2)
- When setting up, make sure that the blade sits correctly on the wet saw’s arbour. There should not be any play if it is properly installed. Do not force the diamond blade or enlarge the inner diameter. (3)
- Verify that the decks are in a perfect state and install them according to instructions. (4)
- Please use all protections included with your machine. (5)
- Please use personal protective equipment. Check the diagrams on the diamond blade. (6)
- Start up your machine and test it. When using wet diamond blades, make sure that there is enough water flow. Make sure that there is no play, vibrations or friction. (7)
- Start cutting gently and continue at a moderate speed. Do not force the blade through, try lateral movements or curved cuts. Make sure that the depth of cut is the appropriate. (8)
- When using a dry blade with a grinder, stop every 10-20 seconds to allow the blade to cool down.
- When a blade starts losing its cutting capabilities but does not seem to be worn, reactivate it by running it through a RUBI dressing stone. (9)
- Once the job is finished, be careful when touching the blade. It might still be too hot.
MORE INFO
CONTACT
- GERMANS BOADA S.A.
- Avda. Olimpíades 89-91
- 08191 RUBI – SPAIN
- Tel. +34 936 80 65 00
- E-mail: info@rubi.com.
- MADE IN CHINA
- FEITA NA CHINA
- FABRIQUÉ EN CHINE
- RUBI UK LTD
- Units 16 & 17, Easter Park
- Ferry Lane, Rainham, Essex
- PM13 9BP – UNITED KINGDOM
- P. 44 (0) 1708559609
- F. 44 (0) 1708553813
- E-mail: rubiuk@rubi.com.
- www.rubi.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>