Shelly WAVEPRO2 Z-Wave Smart Switch Instruction Manual
- June 4, 2024
- Shelly
Table of Contents
Shelly WAVEPRO2 Z-Wave Smart Switch
Device terminals
- N: Neutral terminal
- L: Live terminal (110–240 V AC)
- SW (SW1): Switch/push-button input terminal (controlling O (O1))
- SW2: Switch/push-button input terminal (controlling O2)
- I1: Load circuit 1 input terminal
- I2: Load circuit 2 input terminal
- O (O1): Load circuit 1 output terminal
- O2: Load circuit 2 output terminal
Wires
- N: Neutral wire
- L1(A): Load circuit 1 live wire (110-240 V AC)
- L2(B): Load circuit 2 live wire (110-240 V AC)
- L3(C): Device power supply live wire (110-240 V AC)
Button: S: S button
USER AND SAFETY GUIDE 2-circuit DIN-mountable Z-Wave® smart switch with
potential-free contacts
READ BEFORE USE
This document contains important technical and safety information about the
Device, its safe use and installation.
CAUTION! Before beginning the installation, please read carefully and entirely this guide and any other documents accompanying the Device. Failure to follow the installation procedures could lead to malfunction, danger to your health and life, violation of law or refusal of legal and/or commercial guarantee (if any). Shelly Europe Ltd. is not responsible for any loss or damage in case of incorrect installation or improper operation of this device due to failure of following the user and safety instructions in this guide.
TERMINOLOGY
Gateway – A Z-Wave® gateway, also referred to as a Z-Wave® controller, Z-Wave® main controller, Z-Wave® primary controller, or Z-Wave® hub, etc., is a device that serves as a central hub for a Z-Wave® smart home network. The term “gateway” is used in this document.
S button – The Z-Wave® Service button, which is located on Z-Wave® devices and
is used for various functions such as inclusion (adding), exclusion
(removing), and resetting the device to its factory default settings. The term
“S button” is used in this document.
Device – In this document, the term “Device” is used to refer to the Shelly
Qubino device that is a subject of this guide.
ABOUT SHELLY QUBINO
Shelly Qubino is a line of innovative microprocessor-managed devices, which
allow remote control of electric circuits with a smartphone, tablet, PC, or
home automation system. They work on Z-Wave® wireless communication protocol,
using a gateway, which is required for the configuration of devices. When the
gateway is connected to the internet, you can control Shelly Qubino devices
remotely from anywhere. Shelly Qubino devic-es can be operated in any Z-Wave®
network with other Z-Wave® certified devices from other manufacturers. All
mains operated nodes within the network will act as repeaters regardless of
vendor to increase reliability of the network. Devices are de-signed to work
with older generations of Z-Wave® devices and gateways.
WAVE PRO SERIES
Wave Pro series is a line of devices suitable for homes, offices, retail
stores, manufacturing facilities, and other buildings. Pro devices are DIN-
mountable inside the breaker box, and highly suitable for new building
construction. All Wave Pro devices can be controlled and monitored through the
Z-Wave® network.
ABOUT THE DEVICE
The Device is a DIN rail mountable 2-channel smart switch with potential-free
contacts. It controls the on/off function for two independent electrical
devices with a load up to 16 A per chan-nel (25 A in total). It is compatible
with switches (default) and push-buttons.
INSTALLATION INSTRUCTIONS
The Device can be DIN-mounted inside the breaker box.
For the installation instructions, refer to the wiring scheme (Fig. 1) in this
user guide.
⚠ CAUTION!
- Danger of electrocution. Mounting/installation of the Device to the power grid has to be performed with caution, by a qualified electrician.
- Danger of electrocution. Every change in the connections has to be done after ensuring there is no voltage present at the Device terminals.
- Use the Device only with a power grid and appli-ances that comply with all applicable regulations. A short circuit in the power grid or any appliance connected to the Device may damage it.
- Do not connect the Device to appliances exceed-ing the given max. load!
- Allow at least 10 mm of space around each Pro device if you expect currents higher than 5 A per channel.
- Connect the Device only in the way shown in these instructions. Any other method could cause damage and/or injury.
- Do not install the Device where it can get wet.
- Do not use the Device if it has been damaged!
- Do not attempt to service or repair the Device yourself!
- Before starting the mounting/installation of the Device, check that the breakers are turned off and there is no voltage on their terminals. This can be done with a mains volt-age tester or multimeter. When you are sure that there is no volt-age, you can proceed to connecting the wires.
- Do not shorten the antenna.
- Place the antenna as far away as possible from metal elements as they can cause signal inter-ference.
- Connect the Device using solid single-core cables or stranded cables with ferrules. The cables should have insulation with increased heat resistance, not less than PVC T105°C (221°F).
- RECOMMENDATION: For inductive appliances that cause voltage spikes during switching on/off, such as electrical mo-tors, fans, vacuum cleaners and similar ones, RC snubber (0.1 µF / 100 Ω / 1/2 W / 600 V AC) should be connected parallel to the appliance.
- CAUTION! Do not allow children to play with the push-but-tons/switches connected to the Device. Keep the devices for remote control of Shelly Qubino (mobile phones, tablets, PCs) away from children.
Connect the load circuit to the Device I1, I2, O1 and O2 termi-nals.Connect the Live wire to the Device L terminal, and the Neutral wire to the N terminal as shown on Fig. 1. Connect the two switches or a push-buttons to the Device SW1 and SW2 ter-minal and the Live wire.
EXTENDED USER GUIDE
For more detailed installation instructions, use cases, and comprehensive
guidance on adding/removing the Device to/from a Z-Wave® network, factory
reset, LED signalization, Z-Wave® command classes, parameters, and much more,
refer to the extended user guide at: https://shelly.link/WavePro2-KB-US
SPECIFICATIONS
| Power supply | 110-240 V AC, 50/60 Hz |
|---|---|
| Power consumption | < 0.3 W |
| Max. switching voltage AC | 240 V |
| Max. switching current AC | 16 A per channel, 25 A total |
| Max. switching voltage DC | N/A |
| Max. switching current DC | N/A |
| Overheating protection | Yes |
| Power measurement (W) | No |
| Distance | Up to 40 m indoors (131 ft.) (depends on local condition) |
| Z-Wave® repeater | Yes |
| CPU | Z-Wave® S800 |
| Z-Wave® frequency bands | 908.4 MHz |
| Maximum radio frequency power transmitted in frequency band(s) | < 25 mW |
| Size (H x W x D) | 94x19x69 ±0.5 mm / 3.70×0.75×2.71 ±0.02 in |
| Weight | 73 g / 2.58 oz. |
| Mounting | DIN rail |
| Screw terminals max. torque | 0.4 Nm / 3.54 lbin |
| Conductor cross section | 0.5 to 2.5 mm² / 20 to 14 AWG (green connector) |
0.5 to 1.5 mm² / 20 to 16 AWG (white connectors)
Conductor stripped length| 6 to 7 mm / 0.24 to 0.28 in (green connector)
5 to 6 mm / 0.20 to 0.24 in (white connectors)
Shell material| Plastic
Color| Grey
Ambient temperature| -20°C to 40°C / -5°F to 105°F
Humidity| 30% to 70% RH
Max. altitude| 2000 m / 6562 ft.
OPERATIONAL INSTRUCTIONS
If the SW (SW1) is configured as a switch (default), each toggle of the switch will change the output O (O1) state to the opposite state – on, off, on, etc. If the SW (SW1) is configured as a push-button in the Device settings, each press of the push-button will change the output O (O1) state to the opposite state – on, off, on, etc.
If the SW2 is configured as a switch (default), each toggle of the switch will change the output O2 state to the opposite state – on, off, on, etc. If the SW2 is configured as a push-button in the Device settings, each press of the push-button will change the output O2 state to the opposite state – on, off, on, etc.
SUPPORTED LOAD TYPES
Resistive (incandescent bulbs, heating devices)
Inductive with RC Snubber (LED light drivers, transformers, fans,
refrigerators, air-conditioners)
Capacitive (capacitor banks, electronic equipment, motor start capacitors)
IMPORTANT DISCLAMER
Z-Wave® wireless communication may not always be 100%reliable. This Device
should not be used in situations in which life and/or valuables are solely
dependent on its functioning. If the Device is not recognized by your gateway
or appears incorrectly, you may need to change the Device type manually and
ensure that your gateway supports Z-Wave Plus® multi-channel devices.
DISPOSAL & RECYCLING
This refers to the waste of electrical and electronic equipment. It is
applicable in the US and other countries to collect waste separately.
This symbol on the product or in the accompanying literature indicates that the product should not be disposed of in the daily waste. Wave Pro 2 must be recycled to avoid possible damage to the environment or human health from uncontrolled waste disposal and to promote the reuse of materials and resources. It is your responsibility to dispose of the device separately from general household waste when it is already unusable.
FCC NOTES
- This device complies with Part 15 of the FCC Rules.
- Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification or change to this equipment. Such modifications or change could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal-lation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be de-termined by turning the equipment off and on, the user is en-couraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF exposure statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. The device has been evaluated to meet general RF
exposure requirement. The device can be used in portable exposure condition
without restriction.
ORDERING CODE: QPSW-0A2X16US
MANUFACTURER
Shelly Europe Ltd.
Address: 103 Cherni vrah Blvd., 1407 Sofia, Bulgaria
Tel.: +359 2 988 7435
E-mail: zwave-shelly@shelly.cloud
Support: https://support.shelly.cloud/
Web: https://www.shelly.com
Changes in the contact data are published by the Manufacturer at the official
website.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>